Commit graph

160 commits

Author SHA1 Message Date
Heiko Schocher
ff94bc40af mtd, ubi, ubifs: resync with Linux-3.14
resync ubi subsystem with linux:

commit 455c6fdbd219161bd09b1165f11699d6d73de11c
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Sun Mar 30 20:40:15 2014 -0700

    Linux 3.14

A nice side effect of this, is we introduce UBI Fastmap support
to U-Boot.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Joerg Krause <jkrause@posteo.de>
2014-08-25 19:25:55 -04:00
pekon gupta
46840f66ca mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
This patch add support for BCH16_ECC to omap_gpmc driver.

*need to BCH16 ECC scheme*
With newer SLC Flash technologies and MLC NAND, and large densities, pagesizes
Flash devices have become more suspectible to bit-flips. Thus stronger
ECC schemes are required for protecting the data.
But stronger ECC schemes have come with larger-sized ECC syndromes which require
more space in OOB/Spare. This puts constrains like;
(a) BCH16_ECC can correct 16 bit-flips per 512Bytes of data.
(b) BCH16_ECC generates 26-bytes of ECC syndrome / 512B.
Due to (b) this scheme can only be used with NAND devices which have enough
OOB to satisfy following equation:
OOBsize per page >= 26 * (page-size / 512)

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:10 -04:00
pekon gupta
8d13a730de mtd: nand: omap_gpmc: use macro for register definitions
GPMC can support simultaneous processing of 8 512Byte data chunks, in parallel

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:08 -04:00
David Mosberger
6e1899e633 mtd: nand: fix GET/SET_FEATURES address on 16-bit devices
As per following Sections in ONFI Spec, GET_FEATURES and SET_FEATURES also need
byte-addressing on 16-bit devices.

*Section: Target Initialization"
"The Read ID and Read Parameter Page commands only use the lower 8-bits of the
 data bus. The host shall not issue commands that use a word data width on x16
 devices until the host determines the device supports a 16-bit data bus width
 in the parameter page."

*Section: Bus Width Requirements*
"When the host supports a 16-bit bus width, only data is transferred at the
 16-bit width. All address and command line transfers shall use only the lower
 8-bits of the data bus. During command transfers, the host may place any value
 on the upper 8-bits of the data bus. During address transfers, the host shall
 set the upper 8-bits of the data bus to 00h."

So porting following commit from linux kernel
    commit e34fcb07a6d57411de6e15a47724fbe92c5caa42
    Author: David Mosberger <davidm@egauge.net>  (preserving authorship)
    mtd: nand: fix GET/SET_FEATURES address on 16-bit devices

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:05 -04:00
Brian Norris
27ce9e4290 mtd: nand: force NAND_CMD_READID onto 8-bit bus
As per following Sections in ONFI Spec, NAND_CMD_READID should use only
lower 8-bit for transfering command, address and data even on x16 NAND device.

*Section: Target Initialization"
"The Read ID and Read Parameter Page commands only use the lower 8-bits of the
 data bus. The host shall not issue commands that use a word data width on x16
 devices until the host determines the device supports a 16-bit data bus width
 in the parameter page."

*Section: Bus Width Requirements*
"When the host supports a 16-bit bus width, only data is transferred at the
 16-bit width. All address and command line transfers shall use only the lower
 8-bits of the data bus. During command transfers, the host may place any value
 on the upper 8-bits of the data bus. During address transfers, the host shall
 set the upper 8-bits of the data bus to 00h."

Thus porting  following commit from linux-kernel to ensure that column address
is not altered to align to x16 bus when issuing NAND_CMD_READID command.

    commit 3dad2344e92c6e1aeae42df1c4824f307c51bcc7
    mtd: nand: force NAND_CMD_READID onto 8-bit bus
    Author: Brian Norris <computersforpeace@gmail.com> (preserving authorship)

    The NAND command helpers tend to automatically shift the column address
    for x16 bus devices, since most commands expect a word address, not a
    byte address. The Read ID command, however, expects an 8-bit address
    (i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or
    0x20).

    This fixes the column address for a few drivers which imitate the
    nand_base defaults.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:03 -04:00
pekon gupta
0439d752c5 mtd: nand: omap_elm: use macros for register definitions
This patch adds macros for following parameters of ELM Hardware engine
 - ELM_MAX_CHANNELS: ELM can process 8 data streams simultaneously
 - ELM_MAX_ERRORS: ELM can detect upto 16 ECC error when using BCH16 scheme

Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2014-06-06 17:45:50 -04:00
pekon gupta
41bbe4dd49 mtd: nand: omap_elm: use bch_type instead of nibble count to differentiate between BCH4/BCH8/BCH16
ELM hardware engine support ECC error detection for multiple ECC strengths like
 +------+------------------------+
 |Type  | ECC syndrome length    |
 +------+------------------------+
 |BCH4  | 6.5 bytes = 13 nibbles |
 |BCH8  | 13 byte = 26 nibbles   |
 |BCH16 | 26 bytes = 52 nibbles  |
 +------+------------------------+

Current implementation of omap_elm driver uses ECC syndrom length (in 'nibbles')
to differentiate between BCH4/BCH8/BCH16. This patch replaces it with 'bch_type'

Signed-off-by: Pekon Gupta <pekon@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2014-06-06 17:45:48 -04:00
Masahiro Yamada
dd649f1d00 mtd: delete unused files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
2014-04-17 14:38:30 -04:00
pekon gupta
2eda892f00 mtd: nand: omap: move omap_elm.h from arch/arm/include/asm to drivers/mtd/nand
omap_elm.h is a generic header used by OMAP ELM driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
pekon gupta
6aff050988 mtd: nand: omap: move omap_gpmc.h from arch/arm/include/asm to drivers/mtd/nand
omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
Masahiro Yamada
3b98b57fa7 include: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-01-24 16:59:07 -05:00
Prabhakar Kushwaha
68ec9c85a9 mtd: move & update nand_ecclayout structure (plus board changes)
nand_ecclayout is present in mtd.h at Linux.
Move this structure to mtd.h to comply with Linux.

Also, increase the ecc placement locations to 640 to suport device having
writesize/oobsize of 8KB/640B. This means that the maximum oobsize has gone
up to 640 bytes and consequently the maximum ecc placement locations have
also gone up to 640.

Changes from Prabhabkar's version (squashed into one patch to preserve
bisectability):
 - Added _LARGE to MTD_MAX_*_ENTRIES

   This makes the names match current Linux source, and resolves
   a conflict between
   http://patchwork.ozlabs.org/patch/280488/
   and
   http://patchwork.ozlabs.org/patch/284513/

   The former was posted first and is closer to matching Linux, but
   unlike Linux it does not add _LARGE to the names.  The second adds
   _LARGE to one of the names, and depends on it in a subsequent patch
   (http://patchwork.ozlabs.org/patch/284512/).

 - Made max oobfree/eccpos configurable, and used this on tricorder,
   alpr, ASH405, T4160QDS, and T4240QDS (these boards failed to build
   for me without doing so, due to a size increase).

   On tricorder SPL, this saves 2576 bytes (and makes the SPL build
   again) versus the new default of 640 eccpos and 32 oobfree, and
   saves 336 bytes versus the old default of 128 eccpos and 8 oobfree.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Vipin Kumar <vipin.kumar@st.com>
[scottwood@freescale.com: changes as described above]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2013-11-21 13:32:43 -06:00
Paul Burton
40462e541d mtd: driver _read() returns max_bitflips; mtd_read() returns -EUCLEAN
Linux modified the MTD driver interface in commit edbc4540 (with the
same name as this commit). The effect is that calls to mtd_read will
not return -EUCLEAN if the number of ECC-corrected bit errors is below
a certain threshold, which defaults to the strength of the ECC. This
allows -EUCLEAN to stop indicating "some bits were corrected" and begin
indicating "a large number of bits were corrected, the data held in
this region of flash may be lost soon". UBI makes use of this and when
-EUCLEAN is returned from mtd_read it will move data to another block
of flash. Without adopting this interface change UBI on U-boot attempts
to move data between blocks every time a single bit is corrected using
the ECC, which is a very common occurance on some devices.

For some devices where bit errors are common enough, UBI can get stuck
constantly moving data around because each block it attempts to use has
a single bit error. This condition is hit when wear_leveling_worker
attempts to move data from one PEB to another in response to an
-EUCLEAN/UBI_IO_BITFLIPS error. When this happens ubi_eba_copy_leb is
called to perform the data copy, and after the data is written it is
read back to check its validity. If that read returns UBI_IO_BITFLIPS
(in response to an MTD -EUCLEAN) then ubi_eba_copy_leb returns 1 to
wear_leveling worker, which then proceeds to schedule the destination
PEB for erasure. This leads to erase_worker running on the PEB, and
following a successful erase wear_leveling_worker is called which
begins this whole cycle all over again. The end result is that (without
UBI debug output enabled) the boot appears to simply hang whilst in
reality U-boot busily works away at destroying a block of the NAND
flash. Debug output from this situation:

  UBI DBG: ensure_wear_leveling: schedule scrubbing
  UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
  UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 1027
  UBI DBG: ubi_io_read: read 4096 bytes from PEB 1027:4096
  UBI DBG: ubi_eba_copy_leb: copy LEB 0:0, PEB 1027 to PEB 4083
  UBI DBG: ubi_eba_copy_leb: read 1040384 bytes of data
  UBI DBG: ubi_io_read: read 1040384 bytes from PEB 1027:8192
  UBI: fixable bit-flip detected at PEB 1027
  UBI DBG: ubi_io_write_vid_hdr: write VID header to PEB 4083
  UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:4096
  UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 4083
  UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:4096
  UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:8192
  UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:8192
  UBI: fixable bit-flip detected at PEB 4083
  UBI DBG: schedule_erase: schedule erasure of PEB 4083, EC 55, torture 0
  UBI DBG: erase_worker: erase PEB 4083 EC 55
  UBI DBG: sync_erase: erase PEB 4083, old EC 55
  UBI DBG: do_sync_erase: erase PEB 4083
  UBI DBG: sync_erase: erased PEB 4083, new EC 56
  UBI DBG: ubi_io_write_ec_hdr: write EC header to PEB 4083
  UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:0
  UBI DBG: ensure_wear_leveling: schedule scrubbing
  UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
  ...

This patch adopts the interface change as in Linux commit edbc4540 in
order to avoid such situations. Given that none of the drivers under
drivers/mtd return -EUCLEAN, this should only affect those using
software ECC. I have tested that it works on a board which is
currently out of tree, but which I hope to be able to begin
upstreaming soon.

Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
2013-10-09 12:52:04 -05:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Tom Rini
d6639d10db Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2013-05-31 18:28:47 -04:00
Sergey Lapin
dfe64e2c89 mtd: resync with Linux-3.7.1
This patch is essentially an update of u-boot MTD subsystem to
the state of Linux-3.7.1 with exclusion of some bits:

- the update is concentrated on NAND, no onenand or CFI/NOR/SPI
flashes interfaces are updated EXCEPT for API changes.

- new large NAND chips support is there, though some updates
have got in Linux-3.8.-rc1, (which will follow on top of this patch).

To produce this update I used tag v3.7.1 of linux-stable repository.

The update was made using application of relevant patches,
with changes relevant to U-Boot-only stuff sticked together
to keep bisectability. Then all changes were grouped together
to this patch.

Signed-off-by: Sergey Lapin <slapin@ossfans.org>
[scottwood@freescale.com: some eccstrength and build fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2013-05-31 17:12:03 -05:00
Mike Dunn
956b03e180 mtd: nand: add driver for diskonchip g4 nand flash
This patch adds a driver for the diskonchip G4 nand flash device.  It is based
on the driver from the linux kernel.

This also includes a separate SPL driver.  A separate SPL driver is used because
the device operates in a different mode (reliable mode) when loading a boot
image, and also because the storage format of the boot image is different from
normal data (pages are stored redundantly).  The SPL driver basically mimics how
a typical IPL reads data from the device.  The special operating mode and
storage format are used to compensate for the fact that the IPL does not contain
the BCH ecc decoding algorithm (due to size constraints).  Although the u-boot
SPL *could* use ecc, it operates like an IPL for the sake of simplicity and
uniformity, since the IPL and SPL share the task of loading the u-boot image.
As a side benefit, the SPL driver is very small.

[port from linux kernel 3.4 commit 570469f3bde7f71cc1ece07a18d54a05b6a8775d]

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-05-05 23:47:05 +02:00
York Sun
472d546054 Consolidate bool type
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.

All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.

Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-04-01 16:33:52 -04:00
Joe Hershberger
c788ecfdc3 nand: Move the sub-page read support enable to a flag
Use a flag instead of a hard-coded macro so that sub-page reads can be
enabled in other cases (such as on-die ecc).

This is the same as a5ff4f102937a3492bca4a9ff0c341d78813414c in Linux

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2012-11-26 15:41:28 -06:00
Kim Phillips
0d4c1c91bb include/linux/compat.h: fix warning: preprocessor token {__iomem, __user} redefined
include/linux/compat.h:4:9: warning: preprocessor token __user redefined
include/linux/compiler.h:7:10: this was the original definition
include/linux/compat.h:5:9: warning: preprocessor token __iomem redefined
include/linux/compiler.h:12:10: this was the original definition

fixup __iomem, __user definitions in compat.h code appears to be placed
there as a cover up from a code import from linux when u-boot didn't yet
have a compiler.h, introduced by commit
932394ac43 "Rewrite of NAND code based on
what is in 2.6.12 Linux kernel".

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04 11:00:34 -07:00
Tom Rini
495dbd72dd Merge branch 'master' of git://git.denx.de/u-boot-arm 2012-09-21 14:53:13 -07:00
Marek Vasut
9c790a748f mtd: nand: allow NAND_NO_SUBPAGE_WRITE to be set from driver
This is based on Linux kernel -next:

commit 14f44abf1dafc20ba42ce8616a8fc8fbd1b3712b
Author: Brian Norris <computersforpeace@gmail.com>
Date:   Fri Jul 13 09:28:24 2012 -0700

    mtd: nand: allow NAND_NO_SUBPAGE_WRITE to be set from driver

    The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It
    silently masks off at least one flag that might be set by the driver
    (NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly
    others.

    Really, as long as driver writers exercise a small amount of care with
    NAND_* options, this mask is not necessary at all; it was only here to
    prevent certain options from accidentally being set by the driver. But the
    original thought turns out to be a bad idea occasionally. Thus, kill it.

    Note, this patch fixes some major gpmi-nand breakage.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-09-17 18:54:43 -05:00
Joe Hershberger
33b1d5cae3 nand: consolidate duplicated constants
NAND_CMD_ constants for lock/unlock should be in the header

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-09-17 17:33:42 -05:00
Simon Glass
b572595ee9 nand: Try to align the default buffers
The NAND layer needs to use cache-aligned buffers by default. Towards this
goal. align the default buffers and their members according to the minimum
DMA alignment defined for the architecture.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
2012-09-07 13:54:30 -07:00
Amit Virdi
0e88ff08fe st_smi: Change SMI timeout values
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2012-07-07 14:07:38 +02:00
Vipin KUMAR
f3fcf92d59 st_smi: Add support for SPEAr SMI driver
SMI is the serial memory interface controller provided by ST.

Earlier, a driver exists in the u-boot source code for the SMI IP. However, it
was specific to spear platforms. This commit converts the same driver to a more
generic driver. As a result, the driver files are renamed to st_smi.c and
st_smi.h and moved into drivers/mtd folder for reusability by other platforms
using smi controller peripheral.

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2012-07-07 14:07:38 +02:00
Vipin KUMAR
7f0730a02e mtd/NAND: Add FSMC driver support
Flexible static memory controller is a peripheral provided by ST,
which controls the access to NAND chips along with many other
memory device chips eg NOR, SRAM.

This patch adds the driver support for FSMC controller interfacing
with NAND memory.

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
2012-07-07 14:07:38 +02:00
Mike Frysinger
7b15e2bb9b linux/compat.h: rename from linux/mtd/compat.h
This lets us use it in more places than just mtd code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2012-04-30 16:54:51 +02:00
Lukasz Majewski
e26fd3d3bf onenand: Replace ONENAND_IS_MLC() with ONENAND_HAS_4KB()
This replacement causes 4KB page size devices to work properly with u-boot.

The old ONENAND_IS_MLC() behavior has been preserved by explicit
setting of ONENAND_HAS_4KB_PAGE for those devices.

This change makes the onenand_base.c file more resembling the respective
kernel sources.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>

---
Test HW:
       - Samsung S5PC110 GONI
       - Samsung S5PC210 Universal
2012-04-04 17:08:40 +02:00
Lukasz Majewski
6b3967bbbb onenand:samsung Target dependent OneNAND chip probe function
Separate callback for probing OneNAND memory chip.
If no special function is defined, default implementation will be used.

This approach gives more flexibility for OneNAND device probing.

Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2012-04-04 16:27:34 +02:00
Scott Wood
fb49454b1b nand: reinstate lazy bad block scanning
commit 2a8e0fc8b3 ("nand: Merge changes
from Linux nand driver") accidentally reverted commit
13f0fd94e3 ("NAND: Scan bad blocks
lazily.").

Reinstate the change, as amended by commit
ff49ea8977 ("NAND: Mark the BBT as scanned
prior to calling scan_bbt.").

Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-02-28 14:03:39 -06:00
Scott Wood
1f7b1743d3 Revert "nand: make 1-bit software ECC configurable"
This reverts commit 4fee6c2f29.

It breaks boards that currently rely on soft-ecc, as pointed out here:
http://patchwork.ozlabs.org/patch/140872/

The reverted patch should be resubmitted with documentation, and with the
CONFIG_MTD_ECC_SOFT selected from every board that needs it.  We could
start by looking at what NAND driver the board selects, and whether
that driver ever asks for soft ECC.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-02-28 14:03:39 -06:00
Christian Hitz
4fee6c2f29 nand: make 1-bit software ECC configurable
The software ECC algorithm is not necessary when hardware ECC
is available and can be left out for a smaller image size.
Enable with CONFIG_MTD_ECC_SOFT.

Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:09:02 -06:00
Christian Hitz
ff8a8a7183 nand: Merge changes to BBT from Linux nand driver
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe]

This patch synchronizes the nand driver with the Linux 3.0 state.

Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:09:02 -06:00
Christian Hitz
2a8e0fc8b3 nand: Merge changes from Linux nand driver
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe]

This patch synchronizes the nand driver with the Linux 3.0 state.

Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: minor fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:09:02 -06:00
Christian Hitz
4c6de8560c nand: Merge BCH code from Linux nand driver
[backport from linux commit 02f8c6aee8df3cdc935e9bdd4f2d020306035dbe]

This patch merges the BCH ECC algorithm from the 3.0 Linux kernel.
This enables U-Boot to support modern NAND flash chips that
require more than 1-bit of ECC in software.

Signed-off-by: Christian Hitz <christian.hitz@aizo.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:09:02 -06:00
Simon Schwarz
82645f816f nand: Add common functions to linux/mtd/nand.h
Functions often used in SPL are now part of linux/mtd/nand.h.
Static modifiers are removed from these functions in
drivers/mtd/nand/nand_base.c.

Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Cc: scottwood@freescale.com
Cc: s-paulraj@ti.com
Cc: albert.u.boot@aribaud.net
Acked-by: Scott Wood <scottwood@freescale.com>
2011-12-06 23:59:31 +01:00
Marek Vasut
6d41419f0b NAND: Really ignore bad blocks when scrubbing
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
[scottwood@freescale.com: use chip instead of redundant priv_nand]
Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-10-03 18:35:12 -05:00
Albert ARIBAUD
fa82f871c8 Convert ISO-8859 files to UTF-8
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-08-04 23:34:02 +02:00
Florian Fainelli
0272c718ba NAND: add support for reading ONFI page table
This patch adds support for reading an ONFI page parameter from a NAND
device supporting it. If this is the case, struct nand_chip onfi_version
member contains the supported ONFI version, 0 otherwise.

This allows NAND drivers past nand_scan_ident to set the best timings for the
NAND chip.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-04-01 14:49:08 -05:00
Lei Wen
245eb90091 mtd: nand: Allow caller to pass alternative ID table to nand_scan_ident()
This patch sync with David's patch on Linux for handling nand_scan_ident.

	commit 5e81e88a4c140586d9212999cea683bcd66a15c6
	Author: David Woodhouse <David.Woodhouse@intel.com>
	Date:   Fri Feb 26 18:32:56 2010 +0000

	mtd: nand: Allow caller to pass alternative ID table to nand_scan_ident()

	Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-01-12 17:13:10 -06:00
Florian Fainelli
1ce7084a15 NAND: add NAND_CMD_PARAM (0xec) definition
This command is used to read the device ONFI parameters page.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
2010-12-17 14:32:12 -06:00
Mike Frysinger
0bdecd82dd nand: constify id/manu tables
These id tables need not be writable.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-12-17 14:32:11 -06:00
Enric Balletbo i Serra
456be17dbe mtd: OneNAND: add support for OneNAND manufactured by Numonyx
This patch adds the Numonyx manufacturer code (0x20) to
onenand manufacturers.

Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
2010-10-11 15:15:45 -05:00
Ben Gardiner
4ba692fb1e mtd: add an mtd method for get_len_incl_bad()
The logic to 'spread' mtd partitions needs to calculate the length in
the mtd device, including bad blocks.

This patch introduces a new function, mtd_get_len_incl_bad that can
return both the length including bad blocks and whether that length
was truncated on the device. This new function will be used by the
mtdparts spread command later in this series. The definition of the
function is #ifdef'd out in configurations that do not use the new
'mtdparts spread' command.

Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca>
CC: Scott Wood <scottwood@freescale.com>
2010-10-11 15:11:00 -05:00
Scott Wood
5b8e6bb517 nand: remove dead code and suspend/resume
Get rid of the several "#if 0" sections that were keeping around Linux
code that isn't relevant to U-Boot.  Besides cluttering the code, these
sections make tracking upstream changes harder, rather than easier.
It's easy to discard obviously irrelevant diff hunks that patch rejects,
but it's not as easy to notice hunks that apply cleanly to the #if 0
section, but *are* relevant to U-Boot and require modification elsewhere.

Also remove suspend/resume, as this is not applicable to U-Boot.  Removal
saves 232 bytes on powerpc.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
2010-10-11 15:10:35 -05:00
Matthias Kaehlcke
b63815e313 move definition of macros likely and unlikely to compiler.h
the macros likely and unlikely were defined in include/linux/mtd/compat.h,
but used in code not related to MTD. moved the macro definitions to compiler.h

Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
2010-01-18 00:28:27 +01:00
Sandeep Paulraj
bb3e9828e7 NAND:Extending the nand_ecclayout structure
NANDs with page size of lesser than and equal to 2K are
reaching EOL. They are bing replaced with NANDs of
page size 4K and above.
To support this we have to extend the eccpos field

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2009-11-18 14:26:39 -06:00
Amul Kumar Saha
cacbe91958 Flex-OneNAND driver support
This patch adds support for Flex-OneNAND devices.

Signed-off-by: Rohit Hagargundgi <h.rohit@samsung.com>
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
2009-11-13 16:56:18 -06:00
Sandeep Paulraj
aaa8eec532 NAND: Update to support 64 bit device size
This patch adds support for NANDs greater than 2 GB.
Patch is based on the MTD NAND driver in the kernel.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-11-13 16:56:14 -06:00
Minkyu Kang
f380737478 s5pc1xx: SMDKC100: fix compile warnings
fix the following compile warnings
warning: dereferencing type-punned pointer will break strict-aliasing rules

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2009-10-24 09:55:25 -05:00
Minkyu Kang
4678d674f0 s5pc1xx: support onenand driver
This patch includes the onenand driver for s5pc100

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-10-13 21:13:55 -05:00
Sandeep Paulraj
f83b7f9e8a MTD:NAND: ADD new ECC mode NAND_ECC_HW_OOB_FIRST
This patch adds the new mode NAND_ECC_HW_OOB_FIRST in the nand code to
support 4-bit ECC on TI DaVinci devices with large page (up to 2K) NAND
chips.  This ECC mode is similar to NAND_ECC_HW, with the exception of
read_page API that first reads the OOB area, reads the data in chunks,
feeds the ECC from OOB area to the ECC hw engine and perform any
correction on the data as per the ECC status reported by the engine.

This patch has been accepted by Andrew Morton and can be found at

http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-new-ecc-mode-ecc_hw_oob_first.patch

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:03 -05:00
Sandeep Paulraj
a2c65b47ef NAND: ADD page Parameter to all read_page/read_page_raw API's
This patch adds a new "page" parameter to all NAND read_page/read_page_raw
APIs.  The read_page API for the new mode ECC_HW_OOB_FIRST requires the
page information to send the READOOB command and read the OOB area before
the data area.

This patch has been accepted by Andrew Morton and can be found at
http://userweb.kernel.org/~akpm/mmotm/broken-out/mtd-nand-add-page-parameter-to-all-read_page-read_page_raw-apis.patch

WE would like this to become part of the u-boot GIT as well

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:02 -05:00
Kyungmin Park
ecad289fc6 OneNAND: Remove unused read_spareram
Remove unused read_spareram and add unlock_all as kernel does

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-08-26 15:37:02 -05:00
Scott Wood
be33b046b5 Remove legacy NAND and disk on chip code.
Legacy NAND had been scheduled for removal.  Any boards that use this
were already not building in the previous release due to an #error.

The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed.  There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 19:07:47 -05:00
Stefan Roese
fbdaafaee7 nand: Change NAND_MAX_OOBSIZE to 218 as needed for some 4k page devices
This is needed for the MPC512x NAND driver (fsl_nfc_nand.c) which already
defines such a 4k plus 218 bytes ECC layout.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 17:52:03 -05:00
Wolfgang Denk
8e5e9b940c Coding style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-07 22:35:02 +02:00
Stefan Roese
8d2effea23 mtd: Update MTD infrastructure to support 64bit device size
This patch brings the U-Boot MTD infrastructure in sync with the current
Linux MTD version (2.6.30-rc3). Biggest change is the 64bit device size
support and a resync of the mtdpart.c file which has seen multiple fixes
meanwhile.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kyungmin Park <kmpark@infradead.org>
2009-06-12 20:45:47 +02:00
Stefan Roese
0a57265533 mtd: Add MTD concat support to concatenate multiple MTD NOR devices
This patch adds concatenation support to the U-Boot MTD infrastructure.
By enabling CONFIG_MTD_CONCAT this MTD CFI wrapper will concatenate
all found NOR devices into one single MTD device. This can be used by
e.g by UBI to access a partition that spans over multiple NOR chips.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:45:47 +02:00
Wolfgang Grandegger
33846df28f Add wait flags to support board/chip specific delays
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:40 -05:00
Wolfgang Grandegger
06e9f7df05 Add support for TQM-specific chip select logic to FSL-UPM
For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:39 -05:00
Wolfgang Grandegger
e93c1c169d Add multi chip support to the FSL-UPM driver
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:38 -05:00
Wolfgang Grandegger
6c869637fe NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define

 #define NAND_MAX_CHIPS          CONFIG_SYS_MAX_NAND_DEVICE

but that's bogus and did not work anyhow.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:51 -06:00
Stefan Roese
1ae3986204 OneNAND: Additional sync with 2.6.27
- Add subpage write support
- Add onenand_oob_64/32 ecclayout

This has been missing and without it UBI has some incompatibilies issues
with the current (>= 2.6.27) Linux kernel version. vid_hdr_offset is
placed differently (2048 instead of 512) without this fix.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:48 -06:00
Kyungmin Park
ef0921d6b0 Sync with 2.6.27
Sync with OneNAND kernel codes

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-01-23 10:32:44 -06:00
Wolfgang Denk
455ae7e87f Coding style cleanup, update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-16 01:02:17 +01:00
Kyungmin Park
58be3a1056 UBI: Add basic UBI support to U-Boot (Part 8/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Kyungmin Park
47ae6693f5 UBI: Add basic UBI support to U-Boot (Part 7/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Kyungmin Park
7e6ee7ad27 UBI: Add basic UBI support to U-Boot (Part 6/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Alessandro Rubini
a47f957ab5 NAND: Allow NAND and OneNAND to coexist
This removes in nand.h code that is verbatim duplicated from bbm.h,
including directly bbm.h in nand.h. The previous state of affairs
prevented compiling code for a board hosting both NAND and OneNAND chips.

Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-31 16:37:53 -05:00
Scott Wood
c45912d8ab NAND: sync with 2.6.27
This brings the core NAND code up to date with the Linux kernel.

Since there were several drivers in Linux as of the last update that are
not in u-boot, I'm not bringing over new drivers that have been added
since in the absence of an interested party.

I did not update OneNAND since it was recently synced by Kyungmin Park,
and I'm not sure exactly what the common ancestor is.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-29 10:42:16 -05:00
Kyungmin Park
bfd7f38614 Fix OneNAND read_oob/write_oob functions compatability
Also sync with kernel OneNAND codes

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-21 13:50:20 -05:00
Wolfgang Denk
4b0708093e Coding Style cleanup, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-08-14 14:41:06 +02:00
Wolfgang Denk
28ac671910 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2008-08-14 11:26:22 +02:00
Kyungmin Park
d438d50848 Fix OneNAND build break
Since page size field is changed from oobblock to writesize. But OneNAND is not updated.
- fix bufferram management at erase operation
This patch includes the NAND/OneNAND state filed too.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-13 11:00:19 -05:00
Jean-Christophe PLAGNIOL-VILLARD
cc4a0ceeac drivers/mtd/nand: Move conditional compilation to Makefile
rename CFG_NAND_LEGACY to CONFIG_NAND_LEGACY

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:43 +02:00
Ilya Yanok
13f0fd94e3 NAND: Scan bad blocks lazily.
Rather than scanning on boot, scan upon the first attempt to check the
badness of a block.  This speeds up boot when not using NAND, and reduces
the likelihood of needing to reflash via JTAG if NAND becomes
nonfunctional.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:28 -05:00
Anton Vorontsov
e1c3dbada3 nand: fsl_upm: convert to updated MTD NAND infrastructure
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:27 -05:00
William Juul
5e1dae5c3d Fixing coding style issues
- Fixing leading white spaces
 - Fixing indentation where 4 spaces are used instead of tab
 - Removing C++ comments (//), wherever I introduced them

Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:17 -05:00
William Juul
4cbb651b29 Remove white space at end.
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:16 -05:00
William Juul
cfa460adfd Update MTD to that of Linux 2.6.22.1
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.

This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.

MAKEALL ppc/arm has some issues:
 * DOC/OneNand/nand_spl is not building (I have not tried porting
   these parts, and since I do not have any HW and I am not familiar
   with this code/HW I think its best left to someone else.)

Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
 cpu/ppc4xx/ndfc.c
 cpu/arm926ejs/davinci/nand.c
 board/delta/nand.c
 board/zylonite/nand.c

Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:15 -05:00
Scott Wood
3167c5386e NAND: Rename DEBUG to MTDDEBUG to avoid namespace pollution.
This is particularly problematic now that non-NAND-specific code is
including <nand.h>, and thus all debugging code is being compiled
regardless of whether it was requested, as reported by Scott McNutt
<smcnutt@psyent.com>.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-07-09 17:24:47 -05:00
Sergei Poselenov
248ae5cfc8 NAND: Added support for 128-bit OOB, adapted
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
2008-06-11 00:30:22 -05:00
Wolfgang Grandegger
a75a57ef6e NAND FSL UPM: driver re-write using the hwcontrol callback
This is a re-write of the NAND FSL UPM driver using the more universal
hwcontrol callback (instead of the cmdfunc callback). Here is a brief
list of furher modifications:

- For the time being, the UPM setup writing the UPM array has been
  removed from the driver and must now be done by the board specific
  code.

- The bus width definition in "struct fsl_upm_nand" is now in bits to
  comply with the corresponding Linux driver and 8, 16 and 32 bit
  accesses are supported.

- chip->dev_read is only set if fun->dev_ready != NULL, which is
  required for boards not connecting the R/B pin.

- A few issue have been fixed with MxMR bit manipulation like in the
  corresponding Linux driver.

Note: I think the "io_addr" field of "struct fsl_upm" could be removed
      as well, because the address is already determined by
      "nand->IO_ADDR_[RW]", but I'm not 100% sure.

This patch has been tested on a TQM8548 modules with the NAND chip
Micron MT29F8G08FABWP.

This patch is based on the following patches posted to this list a few
minutes ago:

  PPC: add accessor macros to clear and set bits in one shot
  83xx/85xx/86xx: add more MxMR local bus definitions

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-06-10 18:22:26 -05:00
Scott Wood
135f0a7488 NAND: Provide a sane default for NAND_MAX_CHIPS.
This allows the header to be included regardless of whether a board's
config file provides NAND-related defininitions.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-05-28 11:06:24 -05:00
Wolfgang Denk
53677ef18e Big white-space cleanup.
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-21 00:14:08 +02:00
Anton Vorontsov
cd9d23053d nand: FSL UPM NAND driver
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-01-16 14:14:40 +01:00
Marcel Ziswiler
10c7382bc5 fix various comments
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2008-01-09 21:50:47 +01:00
Kyungmin Park
d7e8ce101a OneNAND support (take #2)
[PATCH 3/3] OneNAND support (take #2)

OneNAND support at U-Boot

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2007-09-17 08:19:08 +02:00
Ulf Samuelsson
7ebb4479b0 [PATCH][NAND] Define the Vendor Id for Micron NAND Flash
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-24 12:12:47 +02:00
Stefan Roese
887e2ec9ec Add support for AMCC Sequoia PPC440EPx eval board
- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
  in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
  please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
  in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006
2006-09-07 11:51:23 +02:00
Wolfgang Denk
b9365a26a1 Code cleanup 2006-07-21 11:56:05 +02:00
Marian Balakowicz
2fc000d756 Remove dependencies between DoC code and old legacy NAND driver.
Necessary defines and data structures were copied to DoC specific files
so that legacy NAND code could be entirely removed from u-boot tree
in the near future.
2006-04-05 20:46:41 +02:00
Wolfgang Denk
bfc81252c0 Minor code cleanup 2006-03-06 13:03:37 +01:00
Bartlomiej Sieka
addb2e1650 Re-factoring the legacy NAND code (legacy NAND now only in board-specific
code and in SoC code). Boards using the old way have CFG_NAND_LEGACY and
BOARDLIBS = drivers/nand_legacy/libnand_legacy.a added. Build breakage for
NETTA.ERR and NETTA_ISDN - will go away when the new NAND support is
implemented for these boards.
2006-03-05 18:57:33 +01:00
Bartlomiej Sieka
038ccac511 Merge with /home/wd/git/u-boot/testing-NAND/ to add new NAND handling. 2006-02-24 09:37:22 +01:00
Wolfgang Denk
ac7eb8a315 Update of new NAND code
Patch by Ladislav Michl, 13 Sep 2005
2005-09-14 23:53:32 +02:00
Wolfgang Denk
932394ac43 Rewrite of NAND code based on what is in 2.6.12 Linux kernel
Patch by Ladislav Michl, 29 Jun 2005
2005-08-17 12:55:25 +02:00
wdenk
384cc68744 Patches by Josef Wagner, 29 Oct 2004:
- Add support for MicroSys CPU87 board
- Add support for MicroSys PM854 board
2005-04-03 22:35:21 +00:00