Commit graph

1465 commits

Author SHA1 Message Date
Masahiro Yamada
4ab3fc5eba kirkwood: kwbimage: refactor CONFIG_SYS_KWD_CONFIG
Pull out "$(SRCTREE)/" from CONFIG_SYS_KWD_CONFIG
and push it into the top Makefile.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Dave Purdy <david.c.purdy@gmail.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Cc: Luka Perkov <luka@openwrt.org>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Cc: Jason Cooper <u-boot@lakedaemon.net>
Cc: Siddarth Gore <gores@marvell.com>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Eric Cooper <ecc@cmu.edu>
Cc: Suriyan Ramasami <suriyan.r@gmail.com>
2014-03-12 17:04:52 -04:00
Tom Rini
5495dae7aa Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-03-10 14:22:54 -04:00
Bo Shen
27019e4a94 arm: atmel: sama5d3: add nand spl boot support
Add NAND SPL boot support with hardware PMECC.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 19:19:13 +01:00
Bo Shen
8a45b0ba87 arm: atmel: sama5d3: add spi spl boot support
Add SPI SPL boot support for sama5d3xek board.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 19:18:33 +01:00
Andreas Henriksson
3ed7c4875d at91 gpio: fix typo in compatibility macro
It's called _pio_ in the version that was added to git.
Apparently it got renamed without updating the macros before it was
applied, c.f.
http://u-boot.10912.n7.nabble.com/U-Boot-PATCH-3-9-V3-add-a-new-AT91-GPIO-driver-td75922.html

Signed-off-by: Andreas Henriksson <andreas.henriksson@endian.se>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-03-09 18:24:54 +01:00
Stephen Warren
87fb553b90 ARM: tegra: fix NV_PA_CSITE_BASE for Tegra124
Tegra124 moved the CSITE block's base address. Fix U-Boot to use
the correct address.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:08 -07:00
Stephen Warren
f3026c1683 ARM: tegra: fix pmc_pwrgate_timer_mult register definition
Register pmc_pwrgate_timer_mult has a different layout on Tegra114 and
Tegra124. Reflect this in pmc.h.

Also, simply write the whole of the register in start_cpu() rather than
doing a read-modify-write; the register is simple enough that the code
can easily construct the entire desired value.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:08 -07:00
Stephen Warren
cd7efc2a94 ARM: tegra: move CONFIG_TEGRAnn
<asm/arch-tegra/tegra.h> needs to use CONFIG_TEGRA* to conditionalize
some definitions, since some modules moved between generations. Move
the definition of CONFIG_TEGRAnn to a header that's included earlier,
so that it's set by the time tegra.h needs to use it.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2014-03-05 16:59:07 -07:00
Tom Rini
e4b87e5b1d Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2014-03-04 21:23:42 -05:00
pekon gupta
2eda892f00 mtd: nand: omap: move omap_elm.h from arch/arm/include/asm to drivers/mtd/nand
omap_elm.h is a generic header used by OMAP ELM driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
pekon gupta
6aff050988 mtd: nand: omap: move omap_gpmc.h from arch/arm/include/asm to drivers/mtd/nand
omap_gpmc.h is a generic header used by OMAP NAND driver for all TI platfoms.
Hence this file should be present in generic folder instead of architecture
specific include folder.
Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
pekon gupta
51d192c40d mtd: nand: omap: merge duplicate GPMC data from different arch-xx headers into common omap_gpmc.h
Each SoC platform (AM33xx, OMAP3, OMAP4, OMAP5) has its own copy of GPMC related
defines and declarations scattered in SoC platform specific header files
like include/asm/arch-xx/cpu.h
However, GPMC hardware remains same across all platforms thus this patch merges
GPMC data scattered across different arch-xx specific header files into single
header file include/asm/arch/omap_gpmc.h

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
pekon gupta
a7e36fc95f mtd: nand: omap: remove unused #defines from common omap_gpmc.h
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
	- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
	- GPMC_NAND_ECC_LP_x8_LAYOUT  (for large page x8 NAND)
	- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
	- GPMC_NAND_ECC_SP_x8_LAYOUT  (for small page x8 NAND)

2) removes unused #defines in common omap_gpmc.h depending on above configs

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
pekon gupta
50899183c9 mtd: nand: omap: remove redundant platform specific header: arch-xx/omap_gpmc.h
Currently there are two sets of omap_gpmc.h header files
(a) arch/arm/include/asm/omap_gpmc.h
 common header file for all platforms, containing defines and declarations used
 by GPMC NAND driver.

(b) arch/arm/include/asm/arch-xx/omap_gpmc.h
 SoC platform specific header file containing defines like ECC layout.

This patch removes platform specific arch-xx/omap_gpmc.c because:
 - GPMC hardware engine is common for all SoC platforms hence only (a) is enough
 - ECC layout is now defined in omap_nand.c driver itself based on ecc-scheme
   selected. Hence all ECC layout declarations in (b) are redundant.

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:04 -06:00
Alexey Brodkin
1ace402239 sizes.h - consolidate for all architectures
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 12:15:01 -05:00
Michal Simek
345d3c0f01 mmc: zynq: Add OF initialization support
Enable initialize sdhci from DTB.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-03-04 09:27:35 -05:00
pekon gupta
f5f1f614bd mtd: nand: omap: optimize chip->ecc.hwctl() for H/W ECC schemes
chip->ecc.hwctl() is used for preparing the H/W controller before read/write
NAND accesses (like assigning data-buf, enabling ECC scheme configs, etc.)

Though all ECC schemes in OMAP NAND driver use GPMC controller for generating
ECC syndrome (for both Read/Write accesses). But but in current code
HAM1_ECC and BCHx_ECC schemes implement individual function to achieve this.
This patch
(1) removes omap_hwecc_init() and omap_hwecc_init_bch()
as chip->ecc.hwctl will re-initializeGPMC before every read/write call.
omap_hwecc_init_bch() -> omap_enable_ecc_bch()

(2) merges the GPMC configuration code for all ECC schemes into
single omap_enable_hwecc(), thus adding scalability for future ECC schemes.
omap_enable_hwecc() + omap_enable_ecc_bch() -> omap_enable_hwecc()

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-03 20:09:03 -06:00
Tom Rini
eeb72e6761 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	arch/arm/cpu/armv7/config.mk
	board/ti/am43xx/mux.c
	include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 16:49:58 -05:00
Albert ARIBAUD
fae56934a0 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-02-24 10:29:59 +01:00
Darwin Rambo
989ce04999 arch: bcm281xx: Initial commit of bcm281xx architecture code
Add bcm281xx architecture support code including a clock framework and
chip reset.  Define register block base addresses for the bcm281xx
architecture and create an empty gpio header file required when
CONFIG_CMD_GPIO is set.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22 19:30:24 +01:00
Darwin Rambo
b3134fce89 arch: kona: Initial commit of kona-common architecture code
The Kona architecture is present on a number of Broadcom mobile SoCs
including the bcm281xx family of chips.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22 19:30:18 +01:00
Dave Gerlach
cd8341b7eb ARM: AM43xx: GP-EVM: Correct GPIO used for VTT regulator control
Schematic indicates GPIO5_7 is to be used for VTT regulator control
rather than GPIO0_21 so modify enable_vtt_regulator to reflect this.
Without this some boards will experience DDR3 corruption and fail to
boot.

Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[trini: Rework patch against mainline]
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 13:55:40 -05:00
Hannes Petermaier
072cefe07d Add support for B&R KWB Motherboard
Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB
Motherboard, using TI's AM3352 SoC.

Most of code is derived from TI's AM335x_EVM

Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: trini@ti.com
2014-02-21 13:55:40 -05:00
Lothar Felten
da4105dfcd am335x: Initial support for Silica Pengwyn board
This patch add support for the Silica Pengwyn board [1]
The board is based on a TI AM3354 CPU [2]
All jumpers removed it will boot from the SDcard, the console is on
UART1 accessible via the FDTI -> USB. The on board NAND flash is
supported and can act as boot medium, depending on jumper settings.
USB Host, USB Device and Ethernet are also provided but untested.

[1]
http://www.silica.com/product/silica-pengwyn-board.html
[2]
http://www.ti.com/product/am3354

Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
[trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused
spi0_pin_mux from Pengwyn support]
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-21 13:54:57 -05:00
Tom Rini
4c89a369c7 Merge branch 'master' of git://git.denx.de/u-boot-spi 2014-02-21 08:00:22 -05:00
Tom Rini
6853e6aa77 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-20 12:18:59 -05:00
Albert ARIBAUD
3e11350255 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	Makefile
	drivers/net/npe/Makefile

These two conflicts arise from commit 0b2d3f20
("ARM: NET: Remove the IXP NPE ethernet driver") and are
resolved by deleting the drivers/net/npe/Makefile file
and removing the CONFIG_IXP4XX_NPE line from Makefile.
2014-02-20 13:16:05 +01:00
Alexey Brodkin
f93f589ca2 spear: move CONFIG_SYS_I2C_BASE from arch-spear/hardware to board configs
Having CONFIG_SYS_I2C_BASE requires DW I2C driver to explicitly include
<arch/hardware.h> which other platforms may not have at all.

It's always good to have a driver platform-independent.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>
2014-02-20 06:49:02 +01:00
Masahiro Yamada
365475e6d1 Move #ifdef(CONFIG_DISPLAY_CPUINFO) from caller to callee
- When CONFIG_DISPLAY_CPUINFO is not enabled,
   print_cpuinfo() should be defined as an empty function
   in a header, include/common.h

 - Remove #ifdef CONFIG_DISPLAY_CPUINFO .. #endif
   from caller, common/board_f.c and arch/arm/lib/board.c

 - Remove redundant prototypes in arch/arm/lib/board.c,
   arch/arm/include/asm/arch-am33x/sys_proto.h and
   board/nokia/rx51/rx51.h, keeping the one in include/common.h

 - Add #ifdef CONFIG_DISPLAY_CPUINFO to the func definition
   where it is missing

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-02-19 11:10:05 -05:00
Dan Murphy
e9024ef27d ARM: O5/dra7xx: Add SATA boot support
Add the SATA boot support for OMAP5 and dra7xx.

Renamed the omap_sata_init to the common init_sata(int dev)
for commonality in with sata stack.

Added the ROM boot device ID for SATA.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2014-02-19 10:47:45 -05:00
Albert ARIBAUD
e7538fee99 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-02-19 12:04:45 +01:00
Andy Ng
da781c60e5 imx6 SION bit has to be on for the pins that are used as ENET_REF_CLK
Signed-off-by: Andy Ng <andreas2025@gmail.com>
2014-02-19 10:57:25 +01:00
Michal Simek
d7e269cfbd zynq: Add support for U-BOOT SPL
SPL is using ps7_init.c/h files which are generated
from design tools which have to be copied to
boards/xilinx/zynq folder before compilation.

BSS section is moved to SDRAM because fat support
requires more space than SRAM size.

Added:
- MMC and QSPI support
- Boot OS directly from SPL
- Enable SPL command

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-02-19 09:41:22 +01:00
Soren Brinkmann
97598fcf10 net: zynq_gem: Calculate clock dividers dynamically
Remove hard coded clock divider setting and use the Zynq clock framework
to dynamically calculate appropriate dividers at run time.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Soren Brinkmann
1cd46ed2d3 net: zynq_gem: Move RCLK details out of driver
The GEM driver should not need to know about Zynq specific details of
RCLK related registers and bitfields in the SLCR. Move those details to
the slcr driver.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Soren Brinkmann
6c3e61de3c zynq: Provide a framework to read clock frequencies
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Michal Simek
bf83495040 zynq: serial: Simplify serial driver initialization
Define both serial uarts in the driver and return
default uart based on board configuration.

- Move baseaddresses to hardware.h
- Define default baudrate and clock values

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Michal Simek
627981213a zynq: Move bootmode to headers
These numbers will be reused by SPL.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-19 09:41:21 +01:00
Albert ARIBAUD
a87a0ce702 Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2014-02-19 07:15:01 +01:00
Sourav Poddar
b56e71e2d4 am43xx: Add qspi support
Add QSPI definitions and clock configuration support.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:41:08 +05:30
Markus Niebel
060aaada06 spi: mxc_spi: i.MX6 DL/S have only 4 eCSPI controller
The dual lite and solo variant have only 4 SPI controller.
respect this in the MXC_SPI_BASE_ADRESSES macro

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:29:26 +05:30
Markus Niebel
d7cbcc762e spi: spi-mxc: add defines for clk inactive state for ECSPI
Provide define for the SCLK_CTL field of the config reg of ECSPI.
While at it, oder the defines to improve readability and make
adding more defines easier.

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-02-18 22:29:26 +05:30
Tom Rini
c4d376fd1c Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-17 14:22:02 -05:00
Stephen Warren
5e77a745b2 ARM: bcm2835: fix mbox POWER_STATE_RESP_ON value
Typo: The correct value is 1 not 2.

Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
2014-02-14 07:57:14 +01:00
Albert ARIBAUD
d53ccdb341 Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master' 2014-02-13 13:30:54 +01:00
Stefano Babic
17998eff90 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-11 12:55:32 +01:00
Fabio Estevam
6d73c23410 mx6: Enable L2 cache support
Add L2 cache support and enable it by default.

Configure the L2 cache in the same way as done by FSL kernel:
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/tree/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_4.1.0

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-02-11 11:24:12 +01:00
Fabio Estevam
94db665579 mx6: Distinguish mx6dual from mx6quad
Currently when we boot a mx6dual U-boot reports that it is a mx6quad.

Report it as MX6D instead:

CPU:   Freescale i.MX6D rev1.2 at 792 MHz

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
2014-02-11 11:24:12 +01:00
Fabio Estevam
6a99f03d69 imx: Introduce a header for the imx cpu versions
Instead of duplicating the CPU definitions at mx5 and mx6 sys_proto.h header
files, introduce a common header to centralize such definitions.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2014-02-11 11:24:11 +01:00
Rajeshwari S Shinde
d3e016cc28 MMC: DWMMC: Correct the CLKDIV register value
This patch corrects the divider value written to CLKDIV register.
Since SDCLKIN is divided inside controller by the DIVRATIO value set
in the CLKSEL register, we need to use the same output clock value to
calculate the CLKDIV value.
as per user manual: cclk_in = SDCLKIN / (DIVRATIO + 1)

Input parameter to mmc_clk is changed to dwmci_host, since
we need the same to read DWMCI_CLKSEL register.

This improves the read timing values for channel 0 on SMDK5250
from 0.288sec to 0.144sec

Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-02-07 17:42:26 +02:00