ls2085a_common.h contains hard-coded information for NOR/NAND flash,
I2C, DDR, etc. These are platform specific. Move them out of common
header file and placed into respective board header files.
Move TEXTBASE to 1MB offset to fit NOR flash with up to 1MB sector
size.
Enable command auto complete. Update prompt symbol. Set fdt_high to
0xa0000000 because Linux requires that the fdt be 8-byte aligned
and below 512 MiB. Besides ensuring compliance with the 512 MiB
limit, this avoids problems with the dtb being misaligned within
the FIT image.
Change the MC FW, MC DPL and Debug server NOR addresses in compliance
with the NOR flash layouts for 128MB flash.
Add PCIe macros. Enable "loadb" command. Disable debug server.
Enable workaround for erratum A008511.
Stop reset on panic for postmortem debugging.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Generic Timer may contain an erroneous value. The workaround is to
read it twice until getting the same value.
Signed-off-by: York Sun <yorksun@freescale.com>
The patch removes unnecessary whitespace to fix checkpatch's
warning: unnecessary whitespace before a quoted newline
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Otherwise the high 32 bits get truncated on 64-bit U-boot.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <yorksun@freescale.com>
This erratum only applies to general purpose DDR controllers in LS2.
It shouldn't be applied to DP-DDR controller. Check DDRC versoin number
before applying workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
Add built-in memory test to catch errors after DDR is initialized, before
any other transactions. To enable this test, define CONFIG_FSL_DDR_BIST.
An environmental variable "ddr_bist" is checked before starting test.
It takes a while (several seconds) depending on system memory size.
Signed-off-by: York Sun <yorksun@freescale.com>
CS0 was not allowed to be empty by u-boot driver in the past to simplify
the driver. This may be inconvenient for some debugging. This patch lifts
the restrictions. Controller interleaving still requires CS0 populated.
Signed-off-by: York Sun <yorksun@freescale.com>
Add/update registers for DDR4, including DQ mappings. Allow raw timing
method used for all controllers. Update mode_9 register to 0x500 for
improved stability. Check DDR controller version number individually
in case a SoC has multiple DDR controllers of different versions.
Increase read-write turnaround for DDR4 high speeds.
Signed-off-by: York Sun <yorksun@freescale.com>
Some SoCs have more than two I2C busses. Instead of adding ifdef
to the driver, macros are put into board header file where
CONFIG_SYS_I2C_MXC is defined.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Heiko Schocher <hs@denx.de>
IFC 2.0 doubled the SRAM size, which means double the number of
ECCSTAT registers. Fix the resulting array overflow.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For fsl-lsch3, IFC is binded with address within 32-bit at fist.
After u-boot relocates to DDR, CS1, CS3 can be binded to higher
address to support large space.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
LDPAA Ethernet driver is a freescale's new ethernet driver based on
Layerscape architecture.
Every ethernet driver controls on DPNI object. Where all DPNIs share
one common DPBP and DPIO object to support Rx and Tx flows.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Cristian Sovaiala <cristian.sovaiala@freescale.com>
CC: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
CC: J. German Rivera <German.Rivera@freescale.com>
[York Sun: s/NetReceive/net_process_received_packet]
Reviewed-by: York Sun <yorksun@freescale.com>
Some boards cannot support device tree due to lack of memory. Add an option
to allow these boards to continue to work (and even use driver model).
This is a 'negative' option since most boards are expected to support device
tree in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is little reason to split these two functions. Bring them together
which simplifies the init sequence.
Signed-off-by: Simon Glass <sjg@chromium.org>
When CONFIG_DM_DEVICE_REMOVE is not enabled, such as in SPL, we cannot
remove or unbind devices and do not expect to get errors when binding
and probing devices. So drop the error path to reduce code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
The printf() in panic() adds about 1.5KB of code size to SPL when compiled
with Thumb-2. Provide a smaller version that does not support printf()-style
arguments and use it in two commonly compiled places.
Signed-off-by: Simon Glass <sjg@chromium.org>
The CONFIG_DM_DEVICE_REMOVE option takes out code related to removing
devices. It should also remove the 'unbind' code since if we cannot
remove we probably don't need to unbind.
Signed-off-by: Simon Glass <sjg@chromium.org>
In many cases SPL only uses a single serial port and there is no need for
alias sequence support. We will just use the serial port pointed to by
stdout-path in the /chosen node.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reverts commit 562f8df18d.
Note: Even un-reverting this patch couldn't works as expected, based
on the latest testing from Heiko Schocher.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
This patch extends the U-Boot "led" command to support automatic blinking
by setting a blink frequency in milliseconds. Additionally the number of
supported LEDs is increased to 6 (0...5).
This will be used by the PCA9551 LED driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This assignment conflicts with code that add flags with
gd->flags |= FOO prior to the execution of this function.
Seems like a historical artifact and creates bugs with
early alloc().
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Switch to CONFIG_ARCH_INTEGRATOR defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Select integrator boards by the combination of platform select (AP/CP)
and core module select (CM720T, CM920T, ...).
This allows us to remove CONFIG_SYS_EXTRA_OPTIONS and make Kconfig
much cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
The board/SoC select menu in arch/arm/Kconfig is still cluttered.
Add ARCH_INTEGRATOR into arch/arm/Kconfig and move the board select
under arch/arm/mach-integrator.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
arch/arm/cpu/arm720t/start.S includes <asm/arch/hardware.h>,
but the hardware.h headers of ARM720T boards are all empty.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
These is a growing trend to license DT files dual GPL and X11
especially in the Linux community. It allows easier reuse of
device trees for other software projects.
This commit prepares for doing so in U-Boot too, since DT files are
often copied from the kernel to U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit d8bafe1310
"ARMv8: enable DM in vexpress64 board" only enabled DM
for the simulated vexpress64 board (FVP) with the
hardcoded clock value for the simulated board, causing
a console regression on the Juno board which was using
a different clock setting.
Fix this by enabling DM for all vexpress64 boards,
defining the clock frequency per-board, deleting the
static array of PL01x ports from the config file and
relying solely on the port defined in the boardfile
using platform data.
Cc: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
some pins on the board have been rerouted to other peripherals, so we
change the pinmux to apply with hardware-design.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
The NAND-version has been become a bit orphan.
Now we need to reactivate it, so bring necessary things:
- loading devicetree
- switch control signal to correct pins
- setup pinmux
- default-environment
up to date.
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
instead of polling everytime the environment, we take usage of the global
gd->fdt_blob variable and check it only against NULL.
Variable "dtbaddr" from environment is needed only one time on loading the
devicetree within "load_devicetree()"
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
These methods should be passed a slave device, not a bus. This matches the
old SPI interface. It is important to know which device is claiming the bus
so passing a bus is not that useful.
Reported-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
It is not necessary to write a zero baud rate to the device, and for some
chips this will cause problems. Drop this code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow this driver to support boards where the register shift is not 0.
This fixes some compiler warnings which appear in that case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This UART permits different register spacing. To support the debug UART on
devices which have a spacing other than 1 byte, allow the shift value to
be specified.
Signed-off-by: Simon Glass <sjg@chromium.org>
For some files I neglected to add a license. Rectify this:
arch/arm/dts/exynos4210-pinctrl-uboot.dtsi
arch/arm/dts/exynos4x12-pinctrl-uboot.dtsi
arch/arm/dts/exynos5250-pinctrl-uboot.dtsi
arch/arm/dts/exynos54xx-pinctrl-uboot.dtsi
arch/arm/dts/s5pc100-pinctrl.dtsi
arch/arm/dts/s5pc110-pinctrl.dtsi
This file came from Linux and has no license information there, so add a
comment to that effect:
arch/sandbox/include/asm/bitops.h
This file also came from Linux - presumably someone from TI could add the
license:
include/dt-bindings/pinctrl/omap.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Ingrid Viitanen <ingrid.viitanen@nokia.com>
We must not clear global_data even in tests, since the ram_buffer (which
is used by malloc()) will also be lost, and subsequent tests will fail.
Zero only the global_data fields that are required for the test to function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Joe Hershberger <joe.hershberger@ni.com>
There are a lot more tests now. To avoid confusion add the updated test
output to the driver model README.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The terminator is missing. Add it for completeness.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Joe Hershberger <joe.hershberger@ni.com>
Since a device can have children in the same uclass as itself, we need
to handle unbinding carefully: we must allow that unbinding a device in a
uclass may cause another device in the same uclass to be unbound.
Adjust the code to cope.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Joe Hershberger <joe.hershberger@ni.com>
The functions:
- uclass_find_device_by_name()
- uclass_get_device_by_name()
searches the required device for the exactly given name.
This patch, presice this fact for both function's comments.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This commit introduces simple tests for functions:
- uclass_find_device_by_name()
- uclass_get_device_by_name()
Tests added by this commit:
- Test: dm_test_uclass_devices_find_by_name: for uclass id: UCLASS_TEST_FDT
* get uclass's devices by uclass_find_first/next_device() each as 'testdev',
* for each returned device, call: uclass_find_device_by_name(),
with previously returned device's name as an argument ('testdev->name').
* for the found device ('founddev') check if:
* founddev != NULL
* testdev == founddev
* testdev->name == founddev->name (by strcmp)
- Test: dm_test_uclass_devices_get_by_name: for uclass id: UCLASS_TEST_FDT
* get uclass's devices by uclass_get_first/next_device() each as 'testdev',
* for each returned device, call: uclass_get_device_by_name(),
with previously returned device's name as an argument ('testdev->name').
* for the found device ('founddev') check if:
* founddev != NULL
* founddev is active
* testdev == founddev
* testdev->name == founddev->name (by strcmp)
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
