Add support for TPM ST33ZP24 spi.
The ST33ZP24 does have a spi interface.
The transport protocol is proprietary.
For spi we are relying only on DM_SPI.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Add support for TPM ST33ZP24 family with i2c.
For i2c we are relying only on DM_I2C.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
I2C protocol is not standardize for TPM 1.2.
TIS prococol is define by the Trusted Computing Group and potentially
available on several TPMs.
tpm_tis_infineon.h header is not generic enough.
Rename tpm_tis_infineon.h to tpm_tis.h and move infineon specific
defines/variables to tpm_tis_infineon.c
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
TPM_TIS_LPC is connected to the LPC bus, not I2C.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
In case CONFIG_DM_TPM was set without any TPM chipset configured a fault
was generated (NULL pointer access).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Add the bootfile name in the DHCP Request packet, in addition
to it already being sent in the DHCP Discover.
This is needed by some DHCP servers so that the bootfile name is
properly returned by the server to the client in the DHCP Ack, as
expected by U-Boot.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Cortina phy cannot support soft reset, this commit implements probe
for Cortina PHY to tell phylib to skip phy soft reset by setting
PHY_FLAG_BROKEN_RESET in flags.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current driver always performs a phy soft reset when connecting the phy
device, but soft reset is not always supported by a phy device, so
introduce a quirk PHY_FLAG_BROKEN_RESET to let such a phy device to skip
soft reset. This commit uses 'flags' of phy device structure to store the
quirk.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The picoseconds to register value divisor(ps_to_regval) should be 60 and not
200. Linux has KSZ9031_PS_TO_REG defined to be 60 as well. 60 is the correct
divisor because the 4-bit skew values are defined from 0x0000(-420ps) to
0xffff(480ps), increments of 60.
For example, a DTS skew value of 420, represents 0ps delay, which should be 0x7.
With the previous divisor of 200, it would result in 0x2, which represents a
-300ps delay.
With this patch, ethernet on the SoCFPGA DE0 Atlas is now able to work with
1Gb ethernet.
References:
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf -> page 26
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the DTS documentation for the Micrel KSZ90x1 binding.
The original document was from:
[commit 4b405efbe12de28b26289282b431323d73992381 from the Linux kernel]
This takes the original document and adds a clarification on how the skew
values are represented in the code.
References:
Micrel ksz9021rl/rn Data Sheet, Revision 1.2. Dated 2/13/2014.
http://www.micrel.com/_PDF/Ethernet/datasheets/ksz9021rl-rn_ds.pdf
Micrel ksz9031rnx Data Sheet, Revision 2.1. Dated 11/20/2014.
http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use the 'autoneg' flag available in phydev when checking if
autoneg is in use.
The previous implementation was checking directly in the PHY
if autoneg was supported. Some PHYs will report that autoneg
is supported, even when it is disabled. Thus it is not possible
to use that bit to determine if autoneg is currently in use or
not.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When configuring a PHY in fixed (forced) link mode, in order for
the changes to be applied, either one of these conditions must
be triggered:
1- PHY is reset
2- Autoneg is restarted
3- PHY transitions from power-down to power-up
Neither of these is currently done, so effectively the fixed link
configuration is not applied in the PHY.
Fix this by setting the Autoneg restart bit.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Micrel PHYs KSZ8021/31 and KSZ8081 have a feature where MDIO address 0
is considered as a broadcast address; the PHY will respond even if it
is not its configured (pinstrapped) address. This feature is enabled
by default.
The Linux kernel disables that feature at initialisation, but not
before it probes the MDIO bus. This causes an issue, because a PHY
at address 3 will be discovered at addresses 0 and 3, but will then
only respond at address 3. Because Linux attaches the first PHY it
discovers on 'eth0', it will attach the PHY from address 0, which
will never answer again.
Fix the issue by disabling the broadcast feature in U-Boot, before
Linux is started.
Signed-off-by: Alexandre Messier <amessier@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Rename this file to make it clear it is for the old networking drivers
and not for use with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Every other uclass is in its own file. Create a new eth-uclass.c file and
move the driver-model code into it, so that networking is consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move eth_current_changed(), eth_set_current(), eth_mac_skip() and
eth_get_name() into the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move the functions which set ethernet environment variables to the common
file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Only half of the init is actually common. Move that part into a new common
file and call it from driver-model and legacy code. More common functions
will be added in future patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We should avoid weak functions with driver model. Existing boards that use
driver model don't need them, so let's kill them off.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This function can fail, so be sure to report any errors that occur.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This property allows to specify fastest connection mode supported by
the MAC (as opposed to features of the phy).
There are situations when phy may handle faster modes than the
MAC (or even it's particular implementation or even due to CPU being too
slow).
This property is a standard one in Linux kernel these days and some
boards do already use it in their device tree descriptions.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
cc: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current implementation only sets "port select" bit for non-1Gb mode.
That works fine if GMAC has just exited reset state but we may as well
change connection mode in runtime. Then we'll need to reprogram GMAC for
that new mode of operation and if previous mode was 10 or 100 Mb and new
one is 1 Gb we'll need to reset port mode bit.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
cc: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This will be used for getting max speed mode of Ethernet interface that
a particular MAC supports from Device Tree blob and later being used for
phy configuration.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This new function will allow MAC drivers to override supported
capabilities of the phy. It is required when MAC cannot handle all
speeds supported by phy.
For example phy supports up-to 1Gb connections while MAC may only work
in modes up to 100 or even 10 Mbit/sec.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Breakdown the PHY_*_FEATURES into per speed defines such that we can
easily re-use them individually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
of_set_phy_supported allows overwiting hardware capabilities of
a phy with values from the devicetree. This does not work with
the genphy driver though because the genphys config_init function
will overwrite all values adjusted by of_set_phy_supported. Fix
this by initialising the genphy features in the phy_driver struct
and in config_init just limit the features to the ones the hardware
can actually support. The resulting features are a subset of the
devicetree specified features and the hardware features.
This is a copy of the patch from Linux kernel, see
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=c242a47238fa2a6a54af8a16e62b54e6e031d4bc
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When a Gigabit PHY device is connected to a 10/100Mbits capable Ethernet
MAC, the driver will restrict the phydev->supported modes to mask off
Gigabit. If the Gigabit PHY comes out of reset with the Gigabit features
set by default in MII_CTRL1000, it will keep advertising these feature,
so by the time we call genphy_config_advert(), the condition on
phydev->supported having the Gigabit features on is false, and we do not
update MII_CTRL1000 with updated values, and we keep advertising Gigabit
features, eventually configuring the PHY for Gigabit whilst the Ethernet
MAC does not support that.
This patches fixes the problem by ensuring that the Gigabit feature bits
are always cleared in MII_CTRL1000, if the PHY happens to be a Gigabit
PHY, and then, if Gigabit features are supported, setting those and
updating MII_CTRL1000 accordingly.
This is a copy of patch from Linux kernel, see
http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=5273e3a5ca94fbeb8e07d31203069220d5e682aa
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
eth_get_dev_by_index() is an API which is not available in driver
model. Use eth_get_dev_by_name() instead, which can also simplifly
the code logic a little bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new member 'tbiaddr' to tsec_private struct. For non-DM driver,
it is initialized as CONFIG_SYS_TBIPA_VALUE, but for DM driver, we
can get this from device tree. Update the bindings doc as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This adds driver model support to Freescale TSEC ethernet driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adapted from the same file name in the kernel device tree bindings
documentation, to use with U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For internal routines like redundant_init(), startup_tsec() and
init_phy(), change to use tsec_private pointer as the parameter.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adjust static functions in a proper order so that forward declaration
of tsec_send() can be avoided.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
rxbd and txbd are declared static with 8 byte alignment requirement,
but they can be put into struct tsec_private as well and are natually
aligned to 8 byte.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present rx_idx and tx_idx are declared as static variables
in the driver codes. To support multiple interfaces, move it to
struct tsec_private.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Clean up the tsec and fsl_mdio driver codes a little bit, by:
- Fix misuse of tab and space here and there
- Use correct multi-line comment format
- Replace license identifier to GPL-2.0+
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The call to pci_eth_init() should not be wrapped with CONFIG_TSEC_ENET.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When doing `dhcp`, there is a bad dhcp server in my network
which always reply dhcp request with yiaddr 0, which cause
uboot can not successfully get ipaddr from the good dhcp server.
But the Linux PC can get the ip address even if there is a bad
dhcp server. This patch is to fix that even if there is a bad
dhcp server, uboot can still get ipaddr and tftp work ok.
The way is to ignore the packets from the bad dhcp server by filtering
out the yiaddr whose value is 0.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
You can now configure LAG on VSC9953's ports using the command:
ethsw [port <port_no>] aggr {[help] | show | <lag_group_no>}
A port must belong to a single LAG. By default, a port
belongs to a LAG equal to the port's number.
For each frame, a hash will be calculated based on
Source/Destination MAC addresses, Source/Destination IP(v4/v6)
addresses, Source/Destination ports. This hash will be used to
select a single egress port from LAG. This also assures
that frames from the same flow will always have the
same egress port.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver for VSC9953 L2 switch IP supports many features and
the documentation needs to be updated.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
By default, the aging period is set to 0, so the dynamic
FDB entries are never removed. This patch sets the aging
time to 300 seconds.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There are only 21 registers reserved between ana_ana and
ana_pgid register groups.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
