This patch added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED
and set it to default value 100000.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE
and set it default to 0.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_FPGA_ZYNQPL and migrates the
values over to the defconfigs.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
This patch added Kconfig support for FPGA_SPARTAN3 and migrates the
values over to the defconfigs.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The u-boot-spl.srec is needed for the minimon update on Gen2 SoCs,
conveniently generate this file if SPL is enabled.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
The u-boot-elf.srec is needed for the minimon update on Gen3 SoCs,
conveniently generate this file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.
Signed-off-by: Marek Vasut <marex@denx.de>
Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig. We can
provide a default for BOOTCOUNT_AM33XX as that's a specific part of the
RTC in use. We can also provide a default for ARCH_LS1043A and
ARCH_LS1021A as they had been previously calculated and their symbols
are in Kconfig. In the case of other QE-enabled platforms, they are not
so we must update the relevant defconfig files. The previous default
only applied in some cases, even on a specific SoC family.
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_I2C
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_RAM
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_ENV
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_AM33XX
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
With the contents of config_distro_defaults.h migrated to Kconfig,
we can remove this header file completely
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of platforms include config_distro_defaults.h but do not enable
CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and
re-sync config files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Do the following to make the symbol names less confusing.
sed -i "s/\([TU][^_]\+\)_FUNCTION_DFU/DFU_OVER_\1/g" \
`git grep _FUNCTION_DFU | cut -d ":" -f 1 | sort -u`
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Get rid of the SH I2C driver on Porter and enable the IIC driver
instead . The old SH I2C is completely broken on Porter anyway
and the DM/DT capable IIC driver allows access to the PMIC too.
Use the DM/DT capable driver instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Set those limits to inform U-Boot about FDT and initramfs placement.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This makes the shell so much more pleasant to use, so enable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
then use the Minimon to flash u-boot-spl.srec using ls,2,e6304000.
To generate u-boot-spl.srec, use objcopy:
arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec
This makes the shell so much more pleasant to use, so enable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All Socfpga boards from ./include/configs/socfpga_* define
CONFIG_HW_WATCHDOG.
To ease CONFIG_HW_WATCHDOG conversion to Kconfig select it in
config ARCH_SOCFPGA (arch/arm/Kconfig) section.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
This converts the following to Kconfig:
CONFIG_SYS_BOOTCOUNT_SINGLEWORD
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Ian Ray <ian.ray@ge.com>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_LIMIT
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
>From DFU_ALT_INFO_EMMC (include/environment/ti/dfu.h) we can see that
rootfs will be flashed to second partition on eMMC. But at the moment we
have only one partition in $partitions environment variable. Let's add
"bootloader" partition prior to "rootfs", so that DFU works correctly.
This also fixes eMMC boot, which looks for rootfs on second partition.
"bootloader" partition start corresponds to "u-boot.img.raw" in DFU
eMMC info, which is 0x300 sector (384 KiB offset from eMMC start).
rootfs start address can be also found from DFU eMMC info.
bootloader-related area is finished at 0x1500 sector (2688 KiB offset
from eMMC start). This should be the start address for rootfs in
$partitions environment variable.
While at it, fix U-Boot environment address to be the same as for
AM57x EVM, so that it doesn't clash with other partitions.
So now eMMC layout looks like this:
===============================================================
0 +------------------------+
| MBR/GPT header | 128 -
128 +------------------------+
| MLO | 256 -
384 +------------------------+
| u-boot.img | 1792 bootloader
2176 +------------------------+
| //////// hole //////// | 256 -
2432 +------------------------+
| U-Boot environment | 128 -
2560 +------------------------+
| U-Boot environment | 128 -
| (redundant) |
2688 +------------------------+
| rootfs | remaining rootfs
end +------------------------+
===============================================================
"hole" area can be used further for storing U-Boot environment (like
it's done in AM57x EVM config file) or for increasing u-boot.img area
(in case u-boot.img size increased, e.g. if new dtbs were added).
This commit conforms with Linux partition table from f6d245b8c5
("arm: am57xx: Fix Linux boot from eMMC") commit, making things in
uniform way.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove CONFIG_BOOT_RETRY_TIME as it doesn't do much good and enable
CONFIG_HUSH_PARSER in xtfpga_defconfig.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Enable fall back option to
qspi boot in case of secure boot.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
config_fallbacks.h has some logic that sets HAVE_BLOCK_DEVICE
based on a list of enabled options. Moving HAVE_BLOCK_DEVICE to
Kconfig allows us to drastically shrink the logic in
config_fallbacks.h
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rename HAVE_BLOCK_DEVICE to CONFIG_BLOCK_DEVICE]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the base and sub-options to Kconfig. Note that we only enable
this in the base sandbox config now.
Cc: Alexey Brodkin <alexey.brodkin@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Is this driver still used anywhere? It's fishy that it's only enabled
in sandbox anymore.
config_fallbacks.h had some logic to automatically select
LIB_RAND if RANDOM_UUID or CMD_UUID were set if LIB_HW_RAND wasn't
already selected. By migrating LIB_HW_RAND to Kconfig, we can
remove this check from config_fallbacks.h and put it into Kconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
[trini: Turn into a choice, add NET_RANDOM_ETHADDR]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_APBH_DMA
CONFIG_APBH_DMA_BURST
CONFIG_APBH_DMA_BURST8
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
[trini: Add in MMC as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_ENV_VARS_UBOOT_CONFIG for all STM32 boards
It allows to retrieve the SoC name into the "soc" environment
variable.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
The motivation for moving MX28 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The motivation for moving MX23 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Since CONFIG_MXC_UART is already in Kconfig, move this from
the header to imx6q_logic_defconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This commit removes an attempt to workaround a previous compilation
warning that is is now fixed in "include/configs/ti_omap3_common.h".
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit fixes the following compiler warnings when DM_SERIAL is
enabled.
---8<-------------------------------------------------------------------
...
CC spl/board/ti/evm/evm.o
In file included from /solution/scm/u-boot-master/board/ti/evm/evm.c:16:0:
/solution/scm/u-boot-master/include/ns16550.h:31:0: warning: "CONFIG_SYS_NS16550_REG_SIZE" redefined
#define CONFIG_SYS_NS16550_REG_SIZE (-1)
In file included from /solution/scm/u-boot-master/include/configs/omap3_evm.h:22:0,
from include/config.h:5,
from /solution/scm/u-boot-master/include/common.h:21,
from /solution/scm/u-boot-master/board/ti/evm/evm.c:14:
/solution/scm/u-boot-master/include/configs/ti_omap3_common.h:33:0: note: this is the location of the previous definition
# define CONFIG_SYS_NS16550_REG_SIZE (-4)
LD spl/board/ti/evm/built-in.o
...
CC spl/drivers/serial/ns16550.o
In file included from /solution/scm/u-boot-master/drivers/serial/ns16550.c:11:0:
/solution/scm/u-boot-master/include/ns16550.h:31:0: warning: "CONFIG_SYS_NS16550_REG_SIZE" redefined
#define CONFIG_SYS_NS16550_REG_SIZE (-1)
In file included from /solution/scm/u-boot-master/include/configs/omap3_evm.h:22:0,
from include/config.h:5,
from /solution/scm/u-boot-master/include/common.h:21,
from /solution/scm/u-boot-master/drivers/serial/ns16550.c:7:
/solution/scm/u-boot-master/include/configs/ti_omap3_common.h:33:0: note: this is the location of the previous definition
# define CONFIG_SYS_NS16550_REG_SIZE (-4)
LD spl/drivers/serial/built-in.o
...
---8<-------------------------------------------------------------------
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These are declared in Kconfig, but some #defines have crept in.
CONFIG_FPGA
CONFIG_FPGA_ALTERA
CONFIG_FPGA_CYCLON2
CONFIG_FPGA_SOCFPGA
CONFIG_FPGA_XILINX
CONFIG_FPGA_ZYNQMPPL
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Selecting CONFIG_USB_FUNCTION_MASS_STORAGE=y in the defconfig leads to
the following error:
cmd/built-in.o: In function `do_usb_mass_storage':
cmd/usb_mass_storage.c:217: undefined reference to `fsg_main_thread'
cmd/usb_mass_storage.c:170: undefined reference to `fsg_init'
CONFIG_USB_FUNCTION_MASS_STORAGE option is built only for
the non-SPL case as per the logic in drivers/usb/gadget/Makefile,
so remove the incorrect CONFIG_SPL ifdefery to fix the build
failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
The board header file included a reference to the starting point
from nitrogen6x.h, but since so much changed, the file bears
little resemblance to that file.
Signed-off-by: Eric Nelson <eric@nelint.com>
The initial implementation of mx6memcal reset the CPU after
running the memory calibration procedure because the generic
board has no information about which boot devices are available.
Now that we have SDP support in SPL, use it to allow a full
U-Boot to be uploaded (i.e. to use "mtest").
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Validate the time at startup:
- in case rtc error add to kernel command line RTC_ERROR
- clamp date to 1-Jan-2036
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The exact definition of a successful boot is defined by user-space.
Determine the boot partition automatically. A partition is selected if
file `/boot/bootcause/firstboot' exists (meaning that the partition has
freshly installed software) OR if file `/boot/fitImage' exists.
When userspace determines that new software was successfully installed,
it must (1) delete `/boot/fitImage' on the _inactive_ partition and (2)
remove `/boot/bootcause/firstboot'.
Enable video, but do not display logos or other version information.
Silence kernel console logging by default.
Print a message to VGA screen in case of boot failure and reset bootcount
to allow the user to attempt boot again.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Change the kernel command line to mount the root filesystem read-only in
order to be able to run filesystem check on it on boot.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Enable bootcount using an EXT file.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Read boot script from shared partition, if available.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Modify configuration to support FIT. Set variable `confidx' from VPD,
in order to load the correct device tree. Modify/simplify U-Boot
environment to support loading FIT image.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Enable the hardware watchdog on bx50v3 to cause it to reset in the event
the board hangs.
Configure GPIO_9 pin as WDOG1_B so that a watchdog timeout results in a
full system reset.
The watchdog is used and reconfigured by systemd approximately 1.7 seconds
into boot. Adding a few seconds for U-Boot and a few more seconds as a
safety margin.
Note that the PCIe controller is _not_ put back into a safe state prior
to board reset. This is a problem if board reset is implemented as CPU
reset.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Instead of programming the hardware directly in the board
implementation, follow the flow documented in doc/README.enetaddr: set
the enet[0-9]*addr environment variable and let the driver program the
hardware.
This avoids duplicating the implementation as it already exists in the
driver (drivers/net/fec_mxc.c: fec_set_hwaddr).
The mapping from the driver's index to the environment variable's name
is documented in README: Note for Redundant Ethernet Interfaces. It is
assumed that eth_devices for the controllers on the board are always
indexed in the same order, i.e. FEC always has the index 2.
The FEC driver does *not* set the flag Set MAC Address on Transmit (bit
set_eth0_mac_address used to do but this is unnecessary as the Linux
networking stack fills in the MAC address.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Modify b450v3, b650v3 and b850v3 defconfigs to enable the network devices
found in these products.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The change in i2c configuration added to support access to the VPD has
inadvertantly caused access to i2c buses 1 & 2 to be lost. This has
resulted in the configuration for the PMIC to be attempted on the wrong
bus and thus isn't taking effect.
Add the required configuration to return access to buses 1 & 2. In order
to ensure that any users of the bus numbering prior to addition in VPD
patches work, add buses before configuration related to mux on bus 0 and
tweak VPD bus usage to fit new numbering scheme.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
nand device needed for mmc config to access nand
for write and update so enabling SPL_SUPPORT to mmc
or nand is wrt to env device rather nand driver check.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Use PSCI 1.0 instead of 0.1 to support more power
management feature like system reset, power off etc..
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
This converts the following to Kconfig:
CONFIG_SYS_OMAP24_I2C_SLAVE
CONFIG_SYS_OMAP24_I2C_SPEED
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
This converts the following to Kconfig:
CONFIG_SYS_DV_CLKMODE
CONFIG_SYS_DA850_PLL0_POSTDIV
CONFIG_SYS_DA850_PLL0_PLLDIV1
CONFIG_SYS_DA850_PLL0_PLLDIV2
CONFIG_SYS_DA850_PLL0_PLLDIV3
CONFIG_SYS_DA850_PLL0_PLLDIV4
CONFIG_SYS_DA850_PLL0_PLLDIV5
CONFIG_SYS_DA850_PLL0_PLLDIV6
CONFIG_SYS_DA850_PLL0_PLLDIV7
CONFIG_SYS_DA850_PLL1_POSTDIV
CONFIG_SYS_DA850_PLL1_PLLDIV1
CONFIG_SYS_DA850_PLL1_PLLDIV2
CONFIG_SYS_DA850_PLL1_PLLDIV3
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch moved ethernet PHY configs of ZynqMP boards
to respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moved ethernet PHY configs of Microblaze board to
respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moved ethernet PHY configs of Zynq boards
to respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove SPL_BUILD dependency from zynqmp.c and move it to header file.
Use only one symbol for including psu_init.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Arasan NFC driver requires the self-init mode,
so it should select it.
Instead of having the config header define the macro,
it's cleaner to select the option at the Kconfig level.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new target which is called as mini configuration
with only emmc functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
emmc support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new target which is called as mini configuration
with only nand functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
nand support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Since 'commit af2f44267 ("fdc spl: use different BOARD_INIT MACRO for spl and tpl")'
board stm32f746-disco can't boot.
The macro CONFIG_IS_ENABLED() can't evaluate the value of
CONFIG_SPL_BOARD_INIT as it was defined in include/configs/stm32f746-disco.h
without attributed value.
Moving CONFIG_SPL_BOARD_INIT from stm32f746-disco.h to mach-stm32/Kconfig
fixes this issue.
Fixes: af2f44267 ("fdc spl: use different BOARD_INIT MACRO for spl and tpl")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Setting config options using headers is deprecated. This patch converts
the BCM2835 Mini-UART to Kconfig.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl01x.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl011.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl010.
Signed-off-by: Alexander Graf <agraf@suse.de>
Firmware on the Raspberry Pi family of devices can dynamically configure either
the PL011, Mini-UART or no device at all to be routed to the user accessible
UART pins.
That means we need to always include both drivers, because we can never be sure
which of the two serial devices firmware actually chooses to use.
Signed-off-by: Alexander Graf <agraf@suse.de>
Since 7e0ed13 ("Convert ARCH_OMAP2PLUS boards' CONFIG_SYS_TEXT_BASE to
Kconfig"), a default SYS_TEXT_BASE was set for all ARCH_OMAP2PLUS devices.
CONFIG_ISW_ENTRY_ADDR is used to set SYS_TEXT_BASE in qspi boot.
Simplify this by directly assigning SYS_TEXT_BASE in the defconfig.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
As clk_stm32f driver is able to retrieve HSE frequency from DT,
CONFIG_STM32_HSE_HZ becomes useless.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The MMC environment offset is getting very close to the end of the U-Boot
binary now. Since we want to make sure this will not overflow, add a size
limit in the board for arm64. arm32 has already that limit enforced in our
custom image generation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Currently, socfpga_common.h does not allow configurations without
network support. This is because CONFIG_CMD_PXE is defined in this
file and distro mode has DHCP hard-coded as available.
Fix this by moving CONFIG_CMD_PXE and CONFIG_MENU to the defconfigs
and by making DHCP optional in BOOT_TARGET_DEVICES(func).
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Convert these configuration options to Kconfig, update board defconfigs
and drop them from whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This reverts commit 57897c13de.
Using bounce_buf.c to handle non-DMA alignment problems is bad as
bounce_buf.c does cache manipulations which is not required. Therefore
revert this patch in favour of local bounce buffer solution in the next
patch.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Jason Rush <jarush@gmail.com>
Acked-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Cleanup unused #define values that are read from the DT.
Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>
Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>
Add macro QIXIS_LBMAP_EMMC, QIXIS_LBMAP_IFC, QIXIS_RCW_SRC_IFC,
QIXIS_RCW_SRC_EMMC to enable IFC and eMMC as boot sources for
qixis commands.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[YS: Modify subject and add commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting
the voltage via LTC3882 regulator.
This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by
disabling the SERDES, changing the SVDD and then re-enabling SERDES.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Restructures common driver to support LTC3882 voltage regulator
chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This converts the following to Kconfig:
CONFIG_SOC_DA8XX
CONFIG_SOC_DA850
CONFIG_DA850_LOWLEVEL
CONFIG_MACH_DAVINCI_DA850_EVM
CONFIG_SYS_DA850_PLL_INIT
CONFIG_SYS_DA850_DDR_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: David Lechner <david@lechnology.com>
[trini: Rework CONFIG_SYS_DA850_PLL_INIT so it's selected on SOC_DA8XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
fat.h unconditionally defines CONFIG_SUPPORT_VFAT (and has done since
2003), so as a result VFAT support is always enabled regardless of
whether a board config defines it or not. Drop this unnecessary option.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Migrate the following symbols to Kconfig:
CONFIG_FS_EXT4
CONFIG_EXT4_WRITE
The definitions in config_fallbacks.h can now be expressed in Kconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
This converts the following to Kconfig:
CONFIG_USB_MUSB_HCD
CONFIG_USB_MUSB_UDC
CONFIG_USB_DAVINCI
CONFIG_USB_OMAP3
CONFIG_USB_DA8XX
CONFIG_USB_AM35X
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_USB_MUSB_OMAP2PLUS
CONFIG_USB_MUSB_AM35X
CONFIG_USB_MUSB_DSPS
CONFIG_USB_MUSB_PIO_ONLY
Signed-off-by: Adam Ford <aford173@gmail.com>
Now the u-boot spi image is greater than 0x90000, increase the same in
env during spi erase.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_CYRUS
CONFIG_IDS8313
CONFIG_MPC8308_P1M
CONFIG_MPC8308RDB
CONFIG_MPC8349EMDS
CONFIG_MPC8349ITXGP
CONFIG_SBC8349
CONFIG_SBC8548
CONFIG_SBC8641D
CONFIG_TQM834X
CONFIG_VE8313
CONFIG_XPEDITE5140
CONFIG_XPEDITE5200
CONFIG_XPEDITE550X
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Mario Six <mario.six@gdsys.cc>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AMCORE
CONFIG_ASTRO5373L
CONFIG_M52277EVB
CONFIG_M5253DEMO
CONFIG_M5253EVBE
CONFIG_M5275EVB
CONFIG_M54418TWR
CONFIG_STMARK2
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
This commit adds UBIFS_NAND to BOOT_TARGET_DEVICES. This will
allow the kernel zImage to be loaded from '/boot/zImage' in UBIFS
(ubi0:rootfs).
Additionally update the *_MMC devices to also load kernel image from
the MMC 0:2 EXT4 file system.
DISTRO_DEFAULTS Setup
=====================
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:2 /boot/zImage and run mmcbootz
[fallback 2] Check MMC 0:2 /boot/uImage and run mmcboot
[fallback 3] Check NAND UBIFS /boot/zImage and run nandbootubifs
[fallback 4] Check NAND partitions and run nandboot
The following "extlinux.conf" can be used to load images in the
top-level of the MMC 0:1 FAT partition.
[MMC(0:1)/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-evm
label omap3-evm
kernel /zImage
fdt /omap3-evm.dtb
append console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.
The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.
Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.
Modified findfdt script in u-boot environment variable to include new k2g board type.
Signed-off-by: Rex Chang <rchang@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Even though in production uImage usually is quite small as
it contains just Linux kernel image during development it might
be pretty convenient to have root-FS built into the same image.
That makes uImage much larger but given on our dev platforms we have
quite a lot of DDR (> 512 MiB) we may afford loading huge uImages.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Sata is equipped on ls1012a and can be a boot source. Add sata boot
support as an option if available.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sata is equipped on ls1046a and can be a boot source. Add sata boot
support as an option if available.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This commit adds support for 96Boards Dragonboard820C.
The board is based on APQ8086 Qualcomm Soc, complying with the
96Boards specification.
Features
- 4x Kyro CPU (64 bit) up to 2.15GHz
- USB2.0
- USB3.0
- ISP
- Qualcomm Hexagon DSP
- SD 3.0 (UHS-I)
- UFS 2.0
- Qualcomm Adreno 530 GPU
- GPS
- BT 4.2
- Wi-Fi 2.4GHz, 5GHz (802.11ac)
- PCIe 2.0
- MIPI-CSI, MIPI-DSI
- I2S
U-Boot boots chained from LK (LK implements the fastboot protocol) in
64-bit mode.
For detailed build instructions see readme.txt in the board directory.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This adds SH_ETHER to drivers/net/Kconfig and convert to Kconfig.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Request that all environment variables containing hard-coded address be
calculated at boot time instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On this platform, there may be up to 1024 unusable chunks of memory.
Increase CONFIG_NR_DRAM_BANKS so that U-Boot can remember all the banks
required to represent such fragmented memory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable CONFIG_SYS_INIT_SP_BSS_OFFSET for all 64-bit Tegra boards. Place
the stack/... 512KiB from the end of the U-Boot binary. This should be
plenty to accommodate the current DTBs (max 64 KiB), early malloc region
(6KiB), stack usage, and plenty of slack, while still not placing it too
far away from the U-Boot binary.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
No 64-bit Tegra uses SPL. Remove various unused definitions from config
headers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some distributions like Fedora expect U-Boot to select a proper
devicetree. Since there are several variants of the cm-fx6 module
featuring different SoC variants and the module can be paired with
several baseboards, it is not viable to hardcode a filename.
Instead, follow the lead of other i.MX6 based devices and try to
determine the devicetree to use with the help of the board name
and the SoC variant exported by the board code, before calling the
distro bootcommand.
For now, only for the Utilite Pro a proper devicetree filename is
known but further variants of the Utilite Computer or other devices
based on the cm-fx6 module may be added in the future.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Like many other i.MX6 based boards, there are multiple variants of
the cm-fx6 module featuring different SoC variants. Furthermore, the
module can be paired with multiple baseboards.
At the same time modern distribution like Fedora require U-Boot to
select a proper devicetree which depends on the SoC variant and the
baseboard.
Thus, export the SoC variant and the actual board to the environment
following the conventions of other i.MX6 devices (e.g. the NXP boards)
such that the environment can select a devicetree file to load.
For now, we only know for sure that the cm-fx6 module and the SB-fx6m
baseboard amount to a Utilite Computer variant (depending on the SoC).
Further combinations may be added in the future; e.g. CompuLab's
evaluation board once someone can verify the identification string
stored in its eeprom.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
To support QSPI DM driver
- Add spi0 alias for qspi node. Which is used for bus number 0.
- Modify the n25q256a@0 compatible property to "spi-flash".
- Modify spi4 (gpio_spi) node to spi5
- Define DM SPI/QSPI related config to enable QSPI
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot-dtb.imx size is about 519KB, so 8 * 64KB conflicts
with u-boot-dtb.imx. Enlarge the offset to 14 * 64KB to fix it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Enable I2C/MMC/GPIO/REGUALTOR/PMIC/USB DM drivers.
There are some dependency, such as when DM MMC enabled, USB compile error.
Also the i.MX I2C MMC DM driver does not support legacy GPIO interface.
So enable them all together.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Add nx25-ae250 board configuartion options for RISC-V
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Using changes in this patch we were able to reduce approx 8k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1088a/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1088a/ls1088a.c to keep
board_early_init_f funcations in case of SPL build.
3. Changes in ls1088a_common.h & ls1088ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove duplicate macro CONFIG_FSL_PCIE_RESET and update its comment.
It enables PCIe reset to fix link width 2x - 4x.
Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The CONFIG_SYS_DPAA_QBMAN define is used by DPAA1 freescale SOCs to
add device tree fixups that allow deep sleep in Linux. The define was
placed in header files included by a number of boards, but was not
explicitly documented in any of the Kconfigs. A description was added
to the drivers/networking menuconfig and default selection for
current SOCs that have this part
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AP325RXA
CONFIG_AP_SH4A_4A
CONFIG_CPU_SH_TYPE_R
CONFIG_ECOVEC
CONFIG_ESPT
CONFIG_MIGO_R
CONFIG_MPR2
CONFIG_MS7720SE
CONFIG_MS7722SE
CONFIG_MS7750SE
CONFIG_R0P7734
CONFIG_R2DPLUS
CONFIG_RSK7203
CONFIG_RSK7264
CONFIG_RSK7269
CONFIG_SH7752EVB
CONFIG_SH7753EVB
CONFIG_SH7757LCR
CONFIG_SH7763RDP
CONFIG_SH7785LCR
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
These macros are all defined once and never checked or used anywhere:
CONFIG_MACH_ASPENITE
CONFIG_MACH_DAVINCI_CALIMAIN
CONFIG_MACH_DOCKSTAR
CONFIG_MACH_EDMINIV2
CONFIG_MACH_GOFLEXHOME
CONFIG_MACH_GONI
CONFIG_MACH_GURUPLUG
CONFIG_MACH_KM_KIRKWOOD
CONFIG_MACH_OPENRD_BASE
CONFIG_MACH_SHEEVAPLUG
Almost all of them were only used for the mach_is_foo() logic in
arch/arm/asm/mach-types.h that were dropped in
commit f9dadaef8b ("arm: Re-sync asm/mach-types.h with
Linux Kernel v4.9")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
This board offers :
_ STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory
and 324 Kbytes of RAM in BGA216 package
_ On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability:
_ Mbed-enabled (mbed.org)
_ USB functions: USB virtual COM port, mass storage, debug port
_ 4 inches 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive
touch screen
_ SAI Audio DAC, with a stereo headphone output jack
_ 3 MEMS microphones
_ MicroSD card connector
_ I2C extension connector
_ 4Mx32bit SDRAM
_ 128-Mbit Quad-SPI NOR Flash
_ Reset and wake-up buttons
_ 4 color user LEDs
_ USB OTG FS with Micro-AB connector
_ Three power supply options:
_ Expansion connectors and Arduino™ UNO V3 connectors
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers
instead of board GPIO initialization.
Remove stm32_gpio.c which is no more used and migrate
structs stm32_gpio_regs and stm32_gpio_priv into
arch-stm32f4/gpio.h to not break compilation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove serial_stm32.c driver and uart init from board file,
use available DM serial_stm32x7.c driver compatible for
STM32F4/F7 and H7 SoCs.
The serial_stm32x7.c driver will be renamed later with a more
generic name as it's shared with all STM32 Socs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_sdram.c driver instead of board
SDRAM initialization.
For that, enable OF_CONTROL, OF_EMBED and STM32_SDRAM flags.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
the values of dt_addr_r/kernel_addr_r/ramdisk_addr_r are taken from
the downstream 'u-boot-2017.03-armada-17.10' release.
the chosen values of scriptaddr and pxefile_addr_r are below fdt_addr_r,
in 1MB steps.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
I do not see a good reason to do this by a CONFIG option that affects
all SoCs. The ram_size can be adjusted by dram_init() at run-time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The i.MX 6UL/ULL feature a Cortex-A7 CPU which suppor the ARM
generic timer. This change makes use of the ARM generic timer in
U-Boot.
This is crucial to make the ARM generic timers usable in Linux since
timer_init() initalizes the system counter module, which is necessary
to use the generic timers CP15 registers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Since commit 051ba9e082 ("Kconfig: mx6ull: Deselect MX6UL from
CONFIG_MX6ULL") CONFIG_MX6ULL does not select CONFIG_MX6UL anymore, so
take this into consideration in all the checks for CONFIG_MX6UL.
This fixes a boot regression.
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Boot scripts located in the root directory of the first partition of
USB, mmc, and SATA drives are executed twice: first by the distro boot
command and then by the legacy boot command. This may have weird side
effects if those scripts only change or extend the environment
(including parts of the boot command itself).
Removing the script execution from the legacy boot command has its own
caveats. For instance, the distro boot command may execute the boot.scr
on the mmc drive, then the boot.scr on the SATA drive, before the
legacy boot command actually boots from the mmc drive. However, the
current behavior would only execute the boot.scr once more before the
actual boot, but it does not prevent the script located on the SATA
drive from being executed, and thus, both scripts from being mixed up.
Considering that the legacy boot command is only in place to boot old
(standard) installations, let's go with the resolution having less
custom code and remove the script execution from the legacy boot
command.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The current default environment of the cm_fx6 is not suitable for
booting modern distributions.
Instead of extending the custom environment, let's use the distro
boot command, which has been developed for precisely this use case.
If the distro boot command fails, fall back to the old behavior
(except for USB drives where the old behaviour is completely covered
by the distro boot command). That way it is still possible to create
"rescue SD cards" for old installations (e.g. if one messes up the
on-flash environment).
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In preparation for supporting the distro boot command, introduce the
standard variables for specifying load addresses, which are documented
in README and doc/README.distro, and replace the custom variables
used so far with them.
Since the current address layout disregards an address for an initramfs,
also switch to the load addresses used and proven by other imx6 boards
(e.g. the wandboard and nitrogen6x), instead of going on with our own
way.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.
It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.
When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.
In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.
https://community.nxp.com/docs/DOC-105652
File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 EVM baseboard.
Additionally:
- CONFIG_SYS_THUMB_BUILD is enabled
- CONFIG_SPL_ENV_SUPPORT is enabled
Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb].
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the
correct dtb is imx6sx-sdb-reva.dtb, so make this possible.
While at it, remove an extra 'mmc dev'.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
There is an #ifdef and #endif with nothing in between. This patch simply
removes this dead/useless code.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Linux device tree contains "ethernet" node for all possible
interface supported by SoC i.e. LS1046A.
It is not necessary for a SerDes protocol to support all possible
interface. So disable unavailable "ethernet" node in device tree.
Also, enable FDT_SEQ_MACADDR_FROM_ENV to fetch MAC address
sequentially from environment variables
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error
when uncompressing Image.gz out of FIT image.
Uncompressing Kernel Image ... Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
and loading Image out of FIT image.
Loading Kernel Image ... Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use dfu_alt_info_emmc variable from include/environment/ti/dfu.h file.
It was probably overlooked when extracting DFU variables to mentioned
file.
This patch fixes DFU on BeagleBone Black, so that we can use commands
like ones below to upgrade various images on eMMC:
=> setenv dfu_alt_info $dfu_alt_info_emmc
=> dfu 0 mmc 1
$ dfu-util -D MLO -a MLO.raw
$ dfu-util -D u-boot.img -a u-boot.img.raw
Without this patch, the user is forced to assign the value to
dfu_alt_info_emmc manually, which contradicts with instructions [1].
[1] http://processors.wiki.ti.com/index.php/Linux_Core_U-Boot_User%27s_Guide
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlo3tMgACgkQykllyylKDCFQvQCfeFgaC/95gx9orLrHxpDx7s46
wwYAmwSoXn6hc9bEzgKIppQHblzfqGU6
=mscK
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.01-rc2-v2' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.01-rc2-v2
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
Increase setup, assertion and hold time related to chip-select signal.
Additional delay is needed for the signal to propogate through FPGA.
This adjustment slightly increase the read and write cycle but has no
impact on burst read or write.
Signed-off-by: York Sun <york.sun@nxp.com>
This commit adds ENV_SIZE and ENV_OFFSET configuration items for
ARCH_ROCKCHIP, but keeps these non-visible (i.e. not prompt is given).
With these new items present, the configuration from the header files
is moved to Kconfig.
Keeping these non-visible is necessary to have the possibility to
select new default values if CONFIG_IS_IN_* is changed (interactively
or with oldconfig). Otherwise it will always be set to a previous
value if used with a prompt. As an example if we do a defconfig with
CONFIG_IS_IN_MMC and change it to CONFIG_IS_IN_SPI_FLASH via
menuconfig, ENV_SIZE and ENV_OFFSET will not be changed to the correct
values as defconfig will already have set them to the default values
of CONFIG_IS_IN_MMC in .config.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
User do not need to access the reserved part in system, remove them
from partition table.
Rename atf to trust as generic name for armv7 do not use ATF.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add LS1012ARDB RevC/RevC1/RevC2/RevD/RevE information and
detect it when u-boot starts up.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to clean up definitions for I2C IO expanders.
The value 0x10 of __SW_BOOT_EMU is wrong. It should be 0x2.
Fixed it in this patch.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is enabling support for SPL QSPI boot.
First of all it is necessary to generate atf-spi.ub which is different
format than atf-uboot.ub (this can be made as legacy image too)
ADDR=`arm-xilinx-linux-gnueabi-readelf -a bl31.elf | grep "Entry point
address" | cut -d ':' -f 2 | sed -e 's/^[ \t]*//'`
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
./tools/mkimage -f auto -A arm64 -T firmware -C none -O u-boot -a $ADDR
-e $ADDR -n "atf1" -E -b arch/arm/dts/zynqmp-zcu102.dtb -d bl31.bin
atf-uboot.ub
./tools/mkimage -A arm64 -T firmware -C none -O u-boot -a $ADDR -e $ADDR
-n "atf-for-qspi" -E -d bl31.bin atf-spi.ub
This patch is using this QSPI layout with offsets:
0 boot.bin
512k atf-ub
640k u-boot.bin
1280k u-boot.img
Which corresponding by writing these images(read from MMC)
mmcinfo
sf probe
load mmc 0 10000000 boot.bin
sf erase 0 +$filesize
sf write 10000000 0 $filesize
load mmc 0 10000000 atf-spi.ub
sf erase 0x80000 +$filesize
sf write 10000000 0x80000 $filesize
load mmc 0 10000000 u-boot.bin
sf erase 0xa0000 +$filesize
sf write 10000000 0xa0000 $filesize
load mmc 0 10000000 u-boot.img
sf erase 0x140000 +$filesize
sf write 10000000 0x140000 $filesize
For testing u-boot running in EL3 you can break atf-spi.ub like this:
sf probe
sf erase 0x80000 +4
Then u-boot.img is executed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This was caused by: "fs/fat: Reduce stack usage"
(sha1:2460098cffacd18729262e3ed36656e6943783ed) which converted
fat code to use malloc. But simple malloc is not freeing space
that's why full malloc implementation is needed.
Malloc space is added to RAM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not perform reset when panic happens because in the next reset
panic happens again and logs are overflood by the same errors.
This can be enabled by default and reset can be performed via watchdog.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is fixing two issues:
1. Insufficient stack size for fat fs buffers
2. Insufficient space in malloc area
Tested on zc702 and zc706.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support automatical distro boot which
scan boot.scr from external storage devices(e.g. SD and USB)
and execute autoboot script.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support automatical distro boot which
scan boot.scr from external storage devices(e.g. SD and USB)
and execute autoboot script.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The BRDCFG5[SPISDHC] register field of Qixis device is used
to control SPI and SDHC signal routing.
10 = Force SDHC Mode
- SPI_CS[0] is routed to CPLD for SDHC_VS use.
- SPI_CS[1] is unused.
- SPI_CS[2:3] are routed to the TDMRiser slot.
11 = Force eMMC Mode
- SPI_CS[0:3] are routed to the eMMC card.
0X = Auto Mode
- If SDHC_CS_B=0 (SDHC card installed): Use SDHC mode
described above.
- Else SDHC_CS_B=1 (no SDHC card installed): Use eMMC
mode described above.
In default the hardware uses auto mode, but sometimes we need
to use force SDHC mode to support SD card hotplug, or SD sleep
waking up in kernel. This patch is to support force SDHC mode
by hwconfig.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The Micron Flash is locked by default. This will automaticlly
unlock so manually unlocking is unnecessary in U-Boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Use 'imply' here liberally to avoid the combinatorial explosion of
defconfig changes in the PowerPC boards.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Use 'imply' here liberally to avoid the combinatorial explosion of
defconfig changes in the PowerPC boards.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Add bits to support yet another board, the R8A77995 D3 Draak.
The DT file is from Linux 4.15-rc1 , commit
b35334447513c14a4dd55a67c269a743d4a4824b .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another board, the R8A77970 V3M Eagle.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another SoC, the R8A77970 V3M .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The partitions variable is especially useful to create a partition table
from U-Boot, either directly from the U-Boot shell, or through flashing
tools like fastboot and its oem format command.
This is especially useful on devices with an eMMC you can't take out to
flash from another system, and booting a Linux system first to flash our
system then is not really practical.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add fall back option, to boot from NOR/QSPI/SD for LS1043, LS1046,
LS1021 in case of distro boot failure.
For LS1046, add kernel validation in case of secure boot in sd_bootcmd
and qspi_bootcmd. For LS1043 and LS1021, add kernel validation in case
of secure boot in sd_bootcmd, qspi_bootcmdand nor_bootcmd.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC
phase using esbc_validate command.
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment
Add header address for PPA to be validated during ESBC phase for
LS1088A platform based on LAyerscape Chasis 3.
Moves sec_init prior to ppa_init as for validation of PPA sec must
be initialised before the PPA is initialised.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Kernel is now located at 0x1000000 instead of 0xa00000
and envirorment variables are located at 3MB offset instead of
2MB in Flash.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This issue is exposed after commit 9000eddbae ("drivers/usb/ehci:
Use platform-specific accessors"), the wrong endianness of EHCI
controller programing will cause USB function down.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This issue is exposed after commit 9000eddbae ("drivers/usb/ehci:
Use platform-specific accessors"), the wrong endianness of EHCI
controller programing will cause USB function down.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:1 zImage and run mmcbootz
[fallback 2] Check MMC 0:1 uImage and run mmcboot
[fallback 3] Check NAND partitions and run nandboot
If 'extlinux.conf' is not found on MMC 0, the previous boot behavior is
followed.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.
But mainline U-Boot and Linux has the old address and size fixed.
These SoCs have a register interface to get the two firmware reserved
memory start and sizes.
This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.
Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html
Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()
Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception
Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds platform code for the Khadas VIM board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds platform code for the Libre Computer CC "Le Potato" board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
evb-rk3128 is an evb from Rockchip based on rk3128 SoC:
- 2 USB2.0 Host port;
- 1 HDMI port;
- 2 10/100M eth port;
- 2GB ddr;
- 16GB eMMC;
- UART to USB debug port;
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
RK3128 is a SoC from Rockchip with quad-core Cortex-A7 CPU
and mali400 GPU. Support Nand flash, eMMC, SD card, USB 2.0 host
and device, HDMI/LVDS/MIPI display.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rework the ULCB CPLD driver and make it into a sysreset driver,
since that is what the ULCB CPLD driver is mostly for.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CONFIG_ENV_IS_IN_NAND has been removed in commit 2be296538e (Convert
CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig).
CONFIG_ENV_IS_IN_SPI_FLASH has been removed in commit 91c868fe7c
(Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig). The environment #ifdef
is now empty. Remove it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This board is based on the Atmel sama5d3 eval boards.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
This board is based on the Atmel 9x5 eval board.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board
which was a prototype.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Stop using the old ad-hoc SH I2C driver and use the new RCar IIC
driver instead. The SH I2C driver should be deprecated and removed
eventually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since we use DM and DT, these SCIF configuration options are useless.
Remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As we have a proper clock framework driver, these macros are not
needed, so drop them and clean up the whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These macros are no longer needed since the DRAM configuration is parsed
from the DT. Drop them all.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since checkboard() is gone, rmobile_sysinfo is also pointless on Gen3.
Furthermore, nuke ad-hoc CONFIG_RCAR_BOARD_STRING which is also dead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since the Gen3 clock driver now has a .remove callback, it is no
longer necessary to shut the clock down before booting Linux in the
arch_preboot_os hook. Stop using it and while doing so, remove all
the ad-hoc config options which this hook used.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull out the GIC macros from the board configuration files
into the common Gen3 configuration file since these macros
are the same for all Gen3 systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The USB support has been switched to DM, so this macro is no
longer meaningful, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable the Micrel KSZ90x1 driver on ULCB, since the board is populated
with KSZ9031 and without this driver, the PHY cannot be operated.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAloeqWoACgkQykllyylKDCHO1wCggsSgQqOPdCo207FqI3yj2p0E
MYkAoI1wKvQcjGJJY19YEC1r70Op8RNo
=BqNN
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.01' of git://www.denx.de/git/u-boot-microblaze
Xilinx changes for v2018.1
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
Generally we load Linux kernels on Boston boards in the form of FIT
images containing a compressed kernel binary. Linux is linked at
0x80100000 and so we need to decompress the kernel binary to that
address, however this is our default load address which means that
unless explicitly avoided we hit a decompression error as the
uncompressed kernel binary overwrites its compressed version from the
FIT image.
Avoid this by adjusting CONFIG_SYS_LOAD_ADDR to 0x88000000 (or
0xffffffff88000000 for MIPS64 builds) which avoids the address overlap
between compressed & uncompressed kernel binaries.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.
ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE 0x40000
was hardcoded.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All these configs were moved to Kconfig that's why this empty ifdef
structure is not needed anymore.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board
contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports
booting from SD.
Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Michal Simek <monstr@monstr.eu>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
mx6sxsabresd can run different kernel versions, such as NXP 4.1 or mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the SD
card changes depending on the kernel version.
In order to avoid such issue, use the UUID method to specify the
rootfs location.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
A few header files still have a definition of CONFIG_ENV_SIZE, causing
warnings during buildman runs. This removes the duplicate definitions
from evb_px5.h, geekbox.h and rv1108_common.h.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There still are a few CONFIG_SPL_* options selected using defines from
rk3188_common.h instead of via Kconfig. This migrates those over to
Kconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
For the RK3188, the BROM will attempt to load up the first stage
image (SPL for the RK3188) in two steps: first 1KB to offset 0x800
in the SRAM and then the remainder to offset 0xc00 in the SRAM.
It always enters at 0x804, though.
With this changeset, the RK3188 boot removes the TPL (stub) stage and
builds a single SPL binary that utilizes the early back-to-bootrom via
the boot0-hook.
Consequently, the passing of the saved boot params via pmu->os_reg[2]
is also removed.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With the boot0-hook inserting the additional padding to receive our
SPL magic, the SPL_TEXT_BASE can be aligned again.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
After we use boot0 hook, we can use offset '000' instead of '004' as
SPL_TEXT_BASE.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated tag in commit summary:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
As per current android recommendation
https://source.android.com/devices/architecture/kernel/modular-kernels
1. Android recovery mode should contain both SOC and ODM
kernel modules in the recovery partition.
2. If a kernel module is required both in recovery and normal boot
mode, the module has to be located in recovery and vendor
partition seperately.
3. Kernel modules used in recovery mode should be independent
of vendor and odm partition
4. Recovery image should contain atleast
storage, display, keypad, battery and pmic modules.
Due to these requirements, recovery image size has increased
to >10MB.
This patch is to increase recovery partition size for TI devices
so that we dont see such flashing error
log:
sending 'recovery' (12560 KB)...
OKAY [ 0.436s]
writing 'recovery'...
FAILED (remote: too large for partition)
finished. total time: 0.458s
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Create board support for GE PPD, based on mx53loco.
Use mx53ppd_defconfig make target to configure for this board.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Command run setup_emmc will create gpt partitions for mmc 0 device
based on patitions variable.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Create layout with a boot 16MiB partition and rootfs with remain
space.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Change dfu_alt_info variable to use the following altsetting:
uboot: To flash raw U-Boot
/zImage: boot: To copy kernel image
/imx6ul-pico-hobbit.dtb: To copy dtb file
rootfs: To copy rootfs
List the currently attached DFU capable USB devices running:
sudo dfu-util -l
Flash U-Boot:
sudo dfu-util -D u-boot.imx -a uboot
Copy boot files:
sudo dfu-util -D zImage -a /zImage
sudo dfu-util -D imx6ul-pico-hobbit.dtb -a /imx6ul-pico-hobbit.dtb
Flash rootfs:
sudo dfu-util -D rootfs.ext4 -a rootfs
To copy boot files you need to have a formated mmc 0:1 partition. To
format with ext4 filesystem you can use ums.
Run on target:
ums 0 mmc 0
and on host:
sudo mkfs.ext4 /dev/sdx1
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the rootfs location is passed via mmcblk number and using
the UUID method to specify the rootfs location is a better approach
working even if mmcblk number for the eMMC changes depending on the
kernel versions.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Create CONFIG_DFU_ENV_SETTINGS to set dfu environment settings to
improve human readable code.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
We first introduce CONFIG_USE_BOOTCOMMAND, similar to
CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most
CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex
scheme around this usage, and these have been defered for the moment so
that platform maintainers can work on a migration plan.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Since CONFIG_DEFAULT_CONSOLE is already started with "console=",
the console argument in CONFIG_EXTRA_ENV_SETTINGS is expanded to
"console=console=ttySAC1,115200n8" and this causes the wrong
console device.
#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0"
...
#define CONFIG_EXTRA_ENV_SETTINGS \
"console=" CONFIG_DEFAULT_CONSOLE
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
