Add Device Model based I2C driver for ast2500/ast2400 SoCs.
The driver is very limited, it only supports master mode and
synchronous byte-by-byte reads/writes, no DMA or Pool Buffers.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
This commit adds support for DM I2C on sunxi platform. It can coexist
with old style sunxi I2C driver, because it is still used in SPL and
by some SoCs.
Because sunxi platform doesn't yet support DM clk, reset and pinctrl
driver, workaround is needed to enable clocks and set resets and
pinctrls. This is done by calling i2c_init_board() in board_init().
This means that CONFIG_I2Cx_ENABLE options needs to be correctly set
in order to use needed I2C controller.
Commit is based on the previous patch made by Philipp Tomsich
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
To enable mipi display, we need to enable pmic
rk808 first for lcd3v3 power,which use i2c0 to
communicate with soc. So enable i2c0.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Cortex-A9 socs rk3066 and rk3188 share the IP but have their own
compatible values, so add them to make the i2c on these platforms accessible.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
This patch allows using i2c commands (e.g. "i2c probe", "i2c md", etc)
without the need to first select the bus number with e.g. "i2c dev 0".
This is the "i2c" command behavior similar to the one from pre DM, where
by default bus 0 was immediately accessible.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch updates the way in which psc, sscl and ssch I2C parameters are
calculated to be in sync with v4.9 Linux kernel
SHA1: 69973b830859bc6529a7a0468ba0d80ee5117826
in the ./drivers/i2c/busses/i2c-omap.c
The previous method was causing several issues:
- The internal I2C frequency (after prescaler) was far above recommended
one (7 - 12 MHz [*]) - the current approach brings better noise suppression
(as stated in Linux commit: SHA1: 84bf2c868f3ca996e5bb)
- The values calculated (psc, sscl and ssch) were far from optimal, which
caused on the test platform (AM57xx) the I2C0 SCL signal low time (Fast
Mode) of ~1.0us (the standard requires > 1.3 us).
[*] for AM57xx TRM SPRUHZ6G, Table 24,7
"HS I2C Register Values for Maximum I2C Bit Rates in I2C F/S, I2C HS Modes"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
v4.9 Linux release:
SHA1: 69973b830859bc6529a7a0468ba0d80ee5117826
in the ./drivers/i2c/busses/i2c-omap.c
recommends to use SCLH=5 and SCLL=7 values.
This patch sets them to default.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Normally, this would probably be done by adding devicetree aliases
to the main dtsi file for the lpc32xx and using bus->req_seq instead.
Since we want to have consistent i2c numbering, we cannot force the
bus->req_seq because. If for instance we have 3 buses numbered
from 0 to 2 with i2c0 enabled, i2c1 disabled and i2c2 enabled;
i2c2 can be selected using 'i2c dev 1' and 'i2c dev 2' commands
because a bus can be probed using req_seq or seq interchangeably.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Since the lpc32xx i2c driver does not yet support the devicetree bindings,
this structure is also needed by the board file as the hardware description
is done there.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
It will enable the driver to support DM and non-DM configurations
using the same functions.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
This is part of the prep work for the migration to the driver model.
What used to be the probe function is now called probe_chip.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Add lpi2c driver for i.MX7ULP.
Need to enable the two options to use this driver:
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_IMX_LPI2C=y
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
With gcc-6.x we see:
drivers/i2c/fsl_i2c.c:86:3: warning: ‘fsl_i2c_speed_map’ defined but not
used [-Wunused-const-variable=]
The easy way to fix this is that since we only use fsl_i2c_speed_map at
all on __M68K__ move the existing guards around slightly.
Reported-by: Thomas Schaefer <Thomas.Schaefer@kontron.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
With the Kconfig re-sync with Linux 4.10, characters such as
'}', ';' in Kconfig help message cause warnings:
$ make defconfig
*** Default configuration is based on 'sandbox_defconfig'
drivers/i2c/Kconfig:132:warning: ignoring unsupported character '}'
drivers/i2c/Kconfig:132:warning: ignoring unsupported character ';'
Drop the Device Tree fragment from the help.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
The readl_poll_timeout() is a useful helper to poll registers
and error out if the condition is not met.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The generic probe code in dm works, so get rid of the leftover cruft.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Revision 1.0 of this IP has a quirk where if during a long read transfer
the transfer_size register will go to 0, the master will send a NACK to
the slave prematurely.
The way to work around this is to reprogram the transfer_size register
mid-transfer when the only the receive fifo is known full, i.e. the I2C
bus is known non-active.
The workaround is based on the implementation in the linux-kernel.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Reorder the timeout loop such that we first check if the
condition is already true, and then call udelay() so if
the condition is already true, break early.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
Revision 1.0 of this IP has a couple of issues, such as not supporting
repeated start conditions for read transfers.
So scan through the list of i2c messages for these conditions
and report an error if they are attempted.
This has been fixed for revision 1.4 of the IP, so only report the error
when the IP can really not do it.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
For mux check if the parent is already a device of UCLASS_I2C and if yes
just use that. Otherwise see if someone specified an i2c-parent phandle.
This mimics the behavior found in the Kernel, as it removes the
requirement to explicitly specify a i2c-parent phandle.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: u-boot@lists.denx.de
If CONFIG_SYS_I2C_S3C24X0_SLAVE isn't defined, then complie error should
be occurred.
This patch is for preventing it.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding additional compatible string for version 1.4 of the IP block.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
0c0f719ad2 accidentally changed the
endianness of the i2c read and write addresses. This was noticable when
accessing EEPROMs that use 2 byte addressing as the LSB was being sent
first.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Some I2C bus devicetree nodes, doesn't require to have
gpio pinctrl so replace the dev_info to debug so the
print never comes on the console and for bus that uses
gpio pinctrl anyway have dev_err.
Before:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 0x21a4000, no gpio pinctrl state.
After:
------
U-Boot> i2c dev 1
Setting bus to 1
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>
Better to print the hex value for bus address instead of
decimal, for more readbility on bus addressing.
Before:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 35274752, no gpio pinctrl state.
After:
------
U-Boot> i2c dev 1
Setting bus to 1
i2c bus 1 at 0x21a4000, no gpio pinctrl state.
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>
Maintainers need to be notified more directly of the need to convert these
drivers. Add a note to the top each affected file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Now that driver model is used for I2C on all boards, we can split the
high-speed code into its own driver. There is virtually no common code,
and this significantly reduces confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Change the error return value -ENODEV from to -EINVAL for more
reasonable.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Due to the peripheral clock driver improvement, remove the
unnecessary clock calling.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Make sure the driver writes the cmd_data register only once per
read transfer instead of doing so potentially repeatedly.
In case the read transfer didn't finish quickly enough, the loop
in the driver code would spin fast enough to write the same value
into the cmd_data register again before re-checking whether the
transfer completed, which would cause another spurious read transfer
on the bus.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
These have now landed upstream. The naming is different and in one case the
function signature has changed. Update the code to match.
This applies the following upstream commits by
Thierry Reding <treding@nvidia.com> :
604e61e fdt: Add functions to retrieve strings
8702bd1 fdt: Add a function to get the index of a string
2218387 fdt: Add a function to count strings
Signed-off-by: Simon Glass <sjg@chromium.org>
This gives a build warning on 64-bit x86. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Boards where ECs that use a I2C port != 0 specify this in the
devicetree file via the google,remote-bus property.
Previously this was ignored and hardcoded to port 0.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
Now that the standard clock/reset APIs are available for all Tegra SoCs,
convert the I2C driver to use them exclusively, and remove any references
to the custom Tegra-specific APIs.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
By adding the "marvell,mv78230-i2c" compatible property, we can enable
this I2C driver to support these new ARM64 chips as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
The I2C bus will get stuck when reading 0 byte. So we add validation of
the read length in i2c_read(). This issue only occurs on read operation.
Signed-off-by: jinghua <jinghua@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
This patch adds runtime speed configuration to the mv_i2c driver.
Currently standard (max 100kHz) and fast mode (max 400kHz) are
supported.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
To prepare for the DM conversion, we add a layer of compatibility
functions to be used by both the legacy and the DM functions.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Heiko Schocher <hs@denx.de>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the 'clk_client.h' doesn't exist, it should be 'clk.h'.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The special handling of the chip address and register address must only
happen before we send the data buffer, otherwise we will end up
inserting both of these every 32 bytes.
Signed-off-by: John Keeping <john@metanate.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no point in writing intermediate values to the txdata
registers.
Also add padding to the debug logging to make it easier to read when
there are leading zeroes.
Signed-off-by: John Keeping <john@metanate.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make it clear that we are using the same value in two adjacent lines.
Signed-off-by: John Keeping <john@metanate.com>
Acked-by: Simon Glass <sjg@chromium.org>
Patch f8a10ed1 [i2c: mvtwsi: Make address length variable] accidentally
inverted the sequence of address bytes sent to the I2C device. This
patch corrects this by sending the highest byte first and the lowest
byte last again.
Tested on theadorable Armada-XP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Heiko Schocher <hs@denx.de>
The nvidia,bpmp property is left over from an old BPMP I2C binding, and
shouldn't be present. Remove it from the SoC DT file, and update the
I2C driver not to parse it; the value wasn't used for anything any more
anyway.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra I2C binding dictates that the clock name for the Tegra I2C clock
be "div-clk" not "i2c". Fix the Tegra186 DT and I2C driver to honor this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds support for the SMBus block read/write functionality.
Other protocols like the SMBus quick command need to get added
if this is needed.
This patch also removed the SMBus related defines from the Ivybridge
pch.h header. As they are integrated in this driver and should be
used from here. This change is added in this patch to avoid compile
breakage to keep the source git bisectable.
Tested on a congatec BayTrail board to configure the SMSC2513 USB
hub.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
clk/reset API was tested on T186 platform and previous chip like
T210/T124 will still use the old APIs.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
(swarren, simplified some ifdefs, removed indent level inside an ifdef)
(swarren, added comment about the ifdefs)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Tegra186, some I2C controllers are directly controlled by the main CPU,
whereas others are controlled by the BPMP, and can only be accessed by the
main CPU via IPC requests to the BPMP. This driver covers the latter case.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some code may want to read reg values from DT, but from nodes that aren't
associated with DM devices, so using dev_get_addr_index() isn't
appropriate. In this case, fdtdec_get_addr_size_*() are the functions to
use. However, "translation" (via the chain of ranges properties in parent
nodes) may still be desirable. Add a function parameter to request that,
and implement it. Update all call sites to default to the original
behaviour.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Squashed in build fix from Stephen:
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2c uclass has a default setting for per_child_platdata_auto_alloc_size
so drivers do not need to set it. Remove this from drivers to avoid
confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As I2C can be used before DRAM initialization for reading EEPROM,
avoid using static variables stored in BSS, since BSS is in DRAM, which
may not have been initialised yet. Explicitly mark "static global"
variables as belonging to the .data section.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Heiko Schocher<hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Due to a oversight in testing, the initialization of the recently
introduced Freescale I2C DM driver works only for 36 bit mode of e.g.
the MPC85XX SoCs (specifically, if the physical addresses are 64 bit
wide and the DT addresses 32 bit wide).
This patch corrects the initialization so that it will work in a more
general setting.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: York Sun <york.sun@nxp.com>
Some devices using the MVTWSI driver have the option to run at speeds
faster than Standard Mode (100kHZ). On the Armada 38x controllers, this
is actually necessary, since due to erratum FE-8471889, a timing
violation concerning repeated starts prevents the controller from
working correctly in Standard Mode. One of the workarounds recommended
in the erratum is to set the bus to Fast Mode (400kHZ) operation and
ensure all connected devices are set to Fast Mode.
In the current version of the driver, however, the delay times are
hard-coded to 10ms, corresponding to Standard Mode operation. To take
full advantage of the faster modes, we would need to either keep the
currently configured I2C speed in a globally accessible variable, or
pass it to the necessary functions as a parameter. For DM, the first
option is not a problem, and we can simply keep the speed in the private
data of the driver. For the legacy interface, however, we would need to
introduce a static variable, which would cause problems with boots from
NOR flashes; see commit d6b7757 "i2c: mvtwsi: Eliminate
twsi_control_flags."
As to not clutter the interface with yet another parameter, we therefore
keep the default 10ms delays for the legacy functions.
In DM mode, we make the delay time dependant on the frequency to allow
taking full advantage of faster modes of operation (tested with up to
1MHZ frequency on Armada MV88F6820).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Zero-length offsets are not properly handled by the driver. When a read
operation with a zero-length offset is started, a START condition is
asserted, and since no offset bytes are transferred, a repeated START is
issued immediately after, which confuses the controller.
To fix this, we send the first START only if any address bytes need to
be sent, and keep track of the expected start status accordingly.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds the necessary functions and Kconfig entry to make the
MVTWSI I2C driver compatible with the driver model.
A possible device tree entry might look like this:
i2c@11100 {
compatible = "marvell,mv64xxx-i2c";
reg = <0x11000 0x20>;
clock-frequency = <100000>;
u-boot,i2c-slave-addr = <0x0>;
};
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The length of the address parameter of the __twsi_i2c_read and
__twsi_i2c_write functions is fixed to four bytes.
As a final step in the preparation of the DM conversion, we make the
length of this parameter variable by turning it into an array of bytes,
and convert the 32 bit value that's passed to the legacy functions into
a four-byte-array on the fly.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
To be able to use the compatibility layer from the DM functions, we
factor the adap parameter out of all functions, and pass the actual
register base instead.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
To prepare for the DM conversion, we add a layer of compatibility
functions to be used by both the legacy and the DM functions.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Since some additional parameters will be added in the course of this
patch series (especially with the addition of DM support), we replace
the longer "unsigned int" declarations with "uint" declarations to keep
the parameter lists more readable.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
The twsi_stop function contains a parameter "status," which is used to
pass in the current exit status of the function calling twsi_stop, and
either return this status unchanged if it indicates an error, or return
twsi_stop's exit status if it does not indicate an error.
While not massively complicated, this adds another purpose to the
twsi_stop function, which should have the sole purpose of asserting a
STOP condition on the bus (and not manage the exit status of its
caller).
Therefore, we move the exit status management into the caller functions
by introducing a "stop_status" variable and returning either the status
before the twsi_stop call (kept in the "status" variable), or the status
from the twsi_stop call, depending on which indicates an error.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Due to breaking boots from NOR flashes, commit d6b7757 ("i2c: mvtwsi:
Eliminate twsi_control_flags") removed the static global
twsi_control_flags variable, which kept a set of default flags that were
always or'd to the control register when writing. It was replaced with a
flags parameter, which was passed around between the functions that
needed it.
Since the twsi_control_flags variable was used just for the purposes of
a) setting the MVTWSI_CONTROL_TWSIEN on every control register write,
and
b) setting the MVTWSI_CONTROL_ACK from twsi_i2c_read if needed,
anyway, the added overhead of another variable being passed around is no
longer justified, and we are better off implementing this flag setting
logic locally in the functions that actually write to the control
register.
Therefore, this patch sets MVTWSI_CONTROL_TWSIEN on every control
register write, replaces the twsi_i2c_read's flags parameter with a
ack_flag parameter, which tells the function whether to acknowledge the
read or not, and removes every other instance of the flags variable.
This has the added benefit that now every notion of "global default
flags" is gone, and it's much easier to see which control flags are
actually set at which point in time.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch fixes only comments/documentation: Streamline capitalization
and improve grammar/punctuation.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Convert groups of logically connected preprocessor defines into proper
enums, one macro into an inline function, and add documentation
to/extend existing documentation of these items.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch fixes seven style violations: Six superfluous spaces after
casts, and one logical continuation violation.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
parse dt parameter of i2c devices only when CONFIG_OF_CONTROL
is enabled.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This does not have much impact on behavior, but makes code look more
more like Linux. The use of devm_ioremap() often helps to delete
.remove callbacks entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add early i2c init function with conservative divider when the exact
clock rate is not available.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In a system where the initial u-boot location is genuinely NOR flash (as
opposed to RAM or a cache-line setup by a pre-bootloader) writes to the
data section are problematic. At best these writes have no effect, at
worst they put the flash memory into a status mode which changes the
executable code underneath us.
Pass around a stack variable from the top of the twsi i2c driver to
avoid writing to global data.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The DW I2C controller in the SPEAr SoCs doesn't support the enable
status register check. This patch selects
SYS_I2C_DW_ENABLE_STATUS_UNSUPPORTED for these boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch adds an entry for the Designware I2C driver in Kconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some platforms don't implement the enable status register at offset 0x9c.
The SPEAr600 platform is one of them. The recently added check to this
status register can't be performend on these platforms.
This patch introduces a new config option that can be enabled on such
platforms not supporting this register.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for common TI i2c mux which is available on ZynqMP zcu102
board.
DM i2c mux core code is selecting/deselecting bus before/after
every command is performed that's why only one channel is active at a
time. That's also the reason why deselect is just disable all available
channels.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
400kHz is maximum freq which can be used on Xilinx ZynqMP.
Support it with standard divider calculator.
Input freq is hardcoded to 100MHz input freq till we have clock driver
which can provide this information for exact configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
set_bus_speed is the right function where bus speed should be setup.
This move enable option to remove probe and remove functions which are
empty.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extract reading IP base address in function which is designed for it.
Also enable option to read more information from DT in this function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds support for the PCI(e) based I2C cores. Which can be
found for example on the Intel Bay Trail SoC. It has 7 I2C controllers
implemented as PCI devices.
This patch also adds the fixed values for the timing registers for
BayTrail which are taken from the Linux designware I2C driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds DM support to the designware I2C driver. It currently
supports DM and the legacy I2C support. The legacy support should be
removed, once all platforms using it have DM enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This patch prepares the designware I2C driver for the DM conversion.
This is mainly done by removing struct i2c_adapter from the functions
that shall be used by the DM driver version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Integrating set_speed() into dw_i2c_set_bus_speed() will make the
conversion to DM easier for this driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
dw_i2c_enable() is used to dis-/en-able the I2C controller. It makes
sense to add such a function, as the controller is dis-/en-abled
multiple times in the code. Additionally, this function now checks,
if the controller is really dis-/en-abled. This code is copied
from the Linux I2C driver version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add the ic_enable_status register to the i2c_regs struct. Additionally
the register offsets are added, to better check, if the offset matches
the register description in the datasheet.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This is a possible drop in replacement for drivers/i2c/zynq-i2c.c
Since this is cadence IP it has been renamed to cdns-i2c,
to make sense with the compatible string.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently, fdtdec_get_addr_size() does not support the address
translation, so it cannot handle device trees with non-straight
"ranges" properties. (This would be a problem with DTS for UniPhier
ARMv8 SoCs.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Implement i2c_idle_bus in driver, then setup_i2c can
be dropped for boards which enable DM_I2C/DM_GPIO/PINCTRL.
The i2c_idle_bus force bus idle flow follows setup_i2c in
arch/arm/imx-common/i2c-mxv7.c
This patch is an implementation following linux kernel patch:
"
commit 1c4b6c3bcf30d0804db0d0647d8ebeb862c6f7e5
Author: Gao Pan <b54642@freescale.com>
Date: Fri Oct 23 20:28:54 2015 +0800
i2c: imx: implement bus recovery
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
"
See Documentation/devicetree/bindings/i2c/i2c-imx.txt for detailed
description.
1. Introuduce scl_gpio/sda_gpio/bus in mxc_i2c_bus.
2. Discard the __weak attribute for i2c_idle_bus and implement it,
since we have pinctrl driver/driver model gpio driver. We can
use device tree, but not let board code to do this.
3. gpio state for mxc_i2c is not a must, but it is recommended. If
there is no gpio state, driver will give tips, but not fail.
4. The i2c controller was first probed, default pinctrl state will
be used, so when need to use gpio function, need to do
"pinctrl_select_state(dev, "gpio")" and after force bus idle,
need to switch back "pinctrl_select_state(dev, "default")".
This is example about how to use the gpio force bus
idle function:
"
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1>;
pinctrl-1 = <&pinctrl_i2c1_gpio>;
scl-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
sda-gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
status = "okay";
[....]
};
[.....]
pinctrl_i2c1_gpio: i2c1grp_gpio {
fsl,pins = <
MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x1b8b0
MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x1b8b0
>;
};
"
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
"Fix mvtwsi not working on sun6i and newer sunxi SoCs" includes the following:
@@ -189,7 +200,8 @@ static int twsi_start(struct i2c_adapter *adap, int expected_status)
/* globally set TWSIEN in case it was not */
twsi_control_flags |= MVTWSI_CONTROL_TWSIEN;
/* assert START */
- writel(twsi_control_flags | MVTWSI_CONTROL_START, &twsi->control);
+ twsi_control_flags |= MVTWSI_CONTROL_START | MVTWSI_CONTROL_CLEAR_IFLG;
+ writel(twsi_control_flags, &twsi->control);
/* wait for controller to process START */
return twsi_wait(adap, expected_status);
}
The modification of twsi_control_flags done here was introduced while
merging to fix a line > 80 chars, but twsi_control_flags is a global variable
and should not be modified like this here, this commit fixes this, restoring
mvtwsi functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Move the init code into the I2C driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is used on most Intel platforms. We don't have a driver for it yet, but
add a stub to handle the init. For now this targets ivybridge so we may want
to add a device tree binding and generalise it when other platforms are
supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since I2C muxes are seldom needed in SPL, and the code for this increases
the size somewhat, add a separate option to enable I2C muxes for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
On sun6i and newer IFLG is a write-clear bit which is cleared by writing 1,
rather then a normal r/w bit which is cleared by writing 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 3 checkpatch warnings
in drivers/i2c/mvtwsi.c:
WARNING: line over 80 characters
ERROR: code indent should use tabs where possible
WARNING: please, no spaces at the start of a line
Signed-off-by: Heiko Schocher <hs@denx.de>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
Until now, the SoC selection for the ARCH_MVEBU platforms has been done
in the config header. Using CONFIG_ARMADA_XP in a non-clear way. As
it needed to get selected for AXP and A38x based boards. This patch
now changes this to move the SoC selection to Kconfig. And also
uses CONFIG_ARCH_MVEBU as a common define for both AXP and A38x.
This makes things a bit clearer - especially for new board additions.
Additionally the defines CONFIG_SYS_MVEBU_DDR_AXP and
CONFIG_SYS_MVEBU_DDR_A38X are replaced with the already available
CONFIG_ARMADA_38X and CONFIG_ARMADA_XP.
And CONFIG_DDR3 is removed, as its not referenced anywhere.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This could avoid executing the code that only applies to i.MX platforms.
The bus_i2c_init() is called before relocation and will assgin value
to a static variable. If U-Boot is then still running in a flash
device, it's theoretically not allowed to write data to flash without
an erasing operation. For i.MX platforms, the U-Boot is always running
in DDR.
Actually it causes asynchronous error when the ARM64 system error
report is enabled and the flash write protect is set.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
compiling U-Boot for avr32 boards shows since
commit 3d1957f0ea "dm: i2c: Add support for multiplexed I2C buses"
this warning:
Building current source for 4 boards (4 threads, 8 jobs per thread)
avr32: + atstk1002
+(atstk1002) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + grasshopper
+(grasshopper) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + atngw100
+(atngw100) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + atngw100mkii
+(atngw100mkii) drivers/i2c/built-in.o: warning: input is not relaxable
0 4 0 /4 0:00:16 : atngw100mkii
Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since busses are sorted in alphabetical order, introducing more
than nine busses led to unexpected behaviour.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Bus has to be held for repeated start regardless of
read/write access.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
Reinhard Pfau complained that macros in ihs_i2c do not follow best practices.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Heiko Schocher <hs@denx.de>
