Commit graph

10 commits

Author SHA1 Message Date
Wolfgang Grandegger
33846df28f Add wait flags to support board/chip specific delays
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:40 -05:00
Wolfgang Grandegger
e93c1c169d Add multi chip support to the FSL-UPM driver
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:38 -05:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Wolfgang Denk
c8a3b109f0 Cleanup out-or-tree building for some boards (.depend)
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-02 23:49:18 +02:00
Wolfgang Grandegger
b4fe1a7109 MPC8360ERDK: adapt NAND interface for the re-written FSL NAND UPM driver
This patch is based on the following patch sent a few minutes ago:
"NAND FSL UPM: driver re-write using the hwcontrol callback"
It is untested, of course. Anton, could you please give it a try.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-06-19 22:54:45 +02:00
Becky Bruce
9973e3c614 Change initdram() return type to phys_size_t
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory.  phys_size_t is defined as an unsigned long on almost
all current platforms.

This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram).  It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.

Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-12 08:50:18 +02:00
Anton Vorontsov
d47d49cc37 mpc83xx: MPC8360E-RDK: configure pario pins for AD7843 and FHCI
This patch adds qe pario pins configuration for AD7843 ADC/Touchscreen
controller and FHCI (QE USB).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-03-25 19:16:47 -05:00
Anton Vorontsov
7ad9594909 mpc83xx: MPC8360E-RDK: add support for NAND
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-03-25 19:16:46 -05:00
Jon Loeliger
a30a549a35 Remove erroneous or extra spd.h #includers.
Many of the spd.h #includers don't need it,
and wanted to have spd_sdram() declared instead.
Since they didn't get that, some also had open
coded extern declarations of it instead or as well.
Fix it all up by using spd_sdram.h where needed.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
2008-03-05 00:17:43 +01:00
Anton Vorontsov
fab6f556bb mpc83xx: add support for the MPC8360E-RDK
This is MPC8360E based board with:
- 256MB fixed SDRAM;
- 8MB Intel Strata NOR flash;
- StMICRO 64MiB NAND flash;
- two 10/100/1000 ethernet ports connected via Broadcom
  BCM5481 PHYs;
- two 10/100 ethernet ports connected via National
  DP83848 PHYs;
- one PCI and one miniPCI slots;
- four serial ports (two NS16550-compatible, two UCCs);
- four USB ports working through MPC8360E "FHCI" USB controller;
- Fujitsu MB86277 graphics controller;
- Analog to Digital Converter/Touchscreen controller, AD7843
  connected to SPI.

Features not supported in this patch are:
- StMICRO 64MiB NAND flash (patch sent);
- MINT framebuffer initialization (patch is pending);
- Fetching production information from the EEPROM via I2C;
- FHCI USB;
- Two slow UCCs used as RS-485 UARTs.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-10 20:52:58 -06:00