As part of various code clean-ups we have on occasion missed removing
unused header files. None of these files are referenced anywhere else
at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove some CONFIG symbols and related comments, etc, that are unused
within the code itself at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add SAMA7G5 series chip id definitions to align with linux SoC driver.
Add support for SAMA7G5 System-In-Package (SIP):
SAMA7G54D1G, SAMA7G54D2G, SAMA7G54D4G.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
sama5d2 contains in its ROM memory BCH code tables for NAND Flash ECC
correction. Enable the use of the GF tables defined in ROM. This should
speed up the boot process, as the tables are no longer constructed at
runtime. Tested with sama5d2-ptc-ek.
Reported-by: David Mosberger-Tang <davidm@egauge.net>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
This reverts commit 786f888b74.
Looks like the datasheet at
https://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D3-Series-Data-sheet-DS60001609b.pdf
is wrong, and the testing was poorly done, because the PMECC did not raise
any error, but also didn't correct any bitflips. Restoring the offsets
as they were before, makes the PMECC on sama5d3x capable of correcting
bitflips.
Fixes: 786f888b74 ("sama5d3: Fix Galois Field Table offsets")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
SAMA7G5 supports slew rate configuration. Adapt the driver for this.
For switching frequencies lower than 50MHz the slew rate needs to
be enabled. Since most of the pins on SAMA7G5 fall into this category
enabled the slew rate by default.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Because ATMEL_BASE_ROM is defined to 0x100000, it already points
to the begin of the index table for 512 byte sectors correction.
Thus its offset must be zero and the index of the table for 1024
byte sectors must start at offset 0x8000.
Signed-off-by: Kai Stuhlemmer (ebee Engineering) <kai.stuhlemmer@ebee.de>
[ta: update commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Offsets are described in the datasheet at section:
"11.4.4.2 NAND Flash Boot: PMECC Error Detection and Correction".
For testing I "injected" bit flips into u-boot NAND memory area,
and then read back. PMECC could not correct the errors. With the
offsets updated everything is fine.
Fixes: 3225f34e5c ("ARM: atmel: add sama5d3xek support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
We already have a function to retrieve the mac address from one EEPROM.
For boards with a second Ethernet interface, however, we would
require another EEPROM with a second unique MAC address.
Introduce at91_set_eth1addr which will look for a second EEPROM
and set the 'eth1addr' variable with the obtained MAC address.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeFDfVAAoJEB6zHgIOrC/IKfsH/2cUfXuc9IgA7L90L3g7htlS
zLAQSC8Xk0WbgbmBJh/lq6zFWj2Mu2yfkZqRzwN8bHkmOPq40F+pEAszVtjH77HM
FpSjMSDVWfNXuhmoiS571dehA0TGi1b2kknrAXqpOwVuMRncMCwaPi8yZYZSGlSV
VzMtguQxD0sZg4oMZVde3tCd41smPTPNDjzLZnXdLa0b09+EtW6enGuk3vzXlS/8
QUT68wUzkeoptJhf3pQ3BXNvkFwdNdYJ74uevDmkAYtvxyl10WNykcwYmH50Q9qq
9plF11EizmTHlj16rWpZLx66RP0s4pziKaeGMr6S8uln33Cr9N496wPqtuDBnvA=
=FYPj
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2020.04 cycle
This feature set is a patch series from Tudor Ambarus which includes
parsing of the spi flash SFDP parser for SST flashes, and using those
tables to retrieve unique saved per device MAC address. This is then
used as base mac address on the SAMA5D2 Wireless SOM EK board.
The SST26VF064BEUI spi-nor flash is programmed at the factory with a
globally unique address stored in the SFDP vendor parameter table and
it is permanently writeprotected. Retrieve the EUI-48 address and set it
as ethaddr env.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
sama5's SFR has at offset 0x04 the DDR Configuration Register,
while sam9x60's SFR contains the EBI Chip Select Register. Add
a union to reconcile both boards.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The Special Function Registers (SFR) are present in sam9x5 and
sam9x60 too, rename sama5_sfr to at91_sfr.h.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add a function in SFR implementation that will open the DDR input
buffers.
This can be called at DRAM initialization time.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
With the new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
The watchdog servicing is enabled via CONFIG_WATCHDOG.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
This patch enables and starts the watchdog on the AT91 platform if
configured. The WD timeout value is read in the AT91 WD device driver
from the DT, using the "timeout-sec" DT property. If not provided in
the DT, the default value of 2 seconds is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
When introducing the SAMA5D27 SoCs, the SAMA5D2 series got an additional
chip id. The check if the cpu is sama5d2 was changed from a preprocessor
definition (inlining a call to 'get_chip_id()') to a C function,
probably to not call get_chip_id twice?
That however broke a check in the macb ethernet driver. That driver is
more generic and also used for other platforms. I suppose this solution
was implemented to use it in 'gem_is_gigabit_capable()', without having
to stricly depend on the at91 platform:
#ifndef cpu_is_sama5d2
#define cpu_is_sama5d2() 0
#endif
That only works as long as cpu_is_sama5d2 is a preprocessor definition.
(The same is still true for sama5d4 by the way.) So this is a straight
forward fix for the workaround.
The not working check on the SAMA5D2 CPU lead to an issue on a custom
board with a LAN8720A ethernet phy connected to the SoC:
=> dhcp
ethernet@f8008000: PHY present at 1
ethernet@f8008000: Starting autonegotiation...
ethernet@f8008000: Autonegotiation complete
ethernet@f8008000: link up, 1000Mbps full-duplex (lpa: 0xffff)
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16
BOOTP broadcast 17
Retry time exceeded; starting again
Notice the wrong reported link speed, although both SoC and phy only
support 100 MBit/s!
The real issue on reliably detecting the features of that cadence
ethernet mac IP block, is probably more complicated, though.
Fixes: 245cbc583d ("ARM: at91: Get the Chip ID of SAMA5D2 SiP")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
When a pin is muxed to a peripheral or as a GPIO, the only
configuration that can be set is the pullup. It is too restrictive
so this patch allows to give a full configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add USB clock driver to configure the input clock and the divider
in the PMC_USB register to generate a 48MHz and a 12MHz signal to
the USB Host OHCI.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
This board is based on the Atmel 9x5 eval board.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Add a header for SAMA5D2 SMC since it's not compatible with
SAMA5D3 one.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[wenyou: fix the wrong base address of the SMC register]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The SAMA5D2 SiP(System in Package) has different Chip IDs in the
CHIPID and CHIP_EXID registers.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refer to the commit 70f8c8316ad(PMC: add new mck function to lower
rate while switching) from AT91Bootstrap.
While switching to a lower clock source, we must switch the clock
source first instead of last. Otherwise, we could end up with
too high frequency on internal bus and peripherals.
This happens on SAMA5D2 as exitting from the ROM code.
Add a function pmc_mck_init_down() to allow this sequence.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As said in 29.5.7 section of SAMA5D2 datasheet, before switching to
the crystal oscillator, a check must be carried out to ensure that
the oscillator is present and that its freqency is valid.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a function to display the company's logo and board information
via the API from DM_VIDEO. This function can be shared by other
atmel boards, so locate it in board/atmel/common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default, it is assumed that the UTMI clock is generated from
a 12 MHz reference clock (MAINCK). If it's not the case, the FREQ
field of the SFR_UTMICKTRIM has to be updated to generate the UTMI
clock in the proper way.
The UTMI clock has a fixed rate of 480 MHz. In fact, there is no
multiplier we can configure. The multiplier is managed internally,
depending on the reference clock frequency, to achieve the target
of 480 MHz.
The patch is cloned from the patch of mailing-list:
[PATCH v2] clk: at91: utmi: set the mainck rate
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
[trini: Depend on SPL_DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Create board/$(VENDOR)/common folder to accommodate the common code
shared by other atmel boards, now put the code to set ethernet mac
address from eeprom, which uses the i2c eeprom driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
