Some SoCs in the mpc83xx family, e.g. mpc8309, have a dedicated spi
chip select, SPISEL_BOOT, that is used by the boot code to boot from
flash.
This chip select will typically be used to select a SPI boot
flash. The SPISEL_BOOT signal is controlled by a single bit in the
SPI_CS register.
Implement a gpio driver for the spi chip select register. This allows a
spi driver capable of using gpios as chip select, to bind a chip select
to SPISEL_BOOT.
It may be a little odd to do this as a GPIO driver, since the signal
is neither GP or I, but it is quite convenient to present it to the
spi driver that way. The alternative it to teach mpc8xxx_spi to handle
the SPISEL_BOOT signal itself (that is how it's done in the linux
kernel, see commit 69b921acae8a)
Signed-off-by: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This parameter "st,phy-cal" becomes optional and when it is
absent the built-in PHY calibration is done.
It is the case in the helper dtsi file "stm32mp15-ddr.dtsi"
except if DDR_PHY_CAL_SKIP is defined.
This patch also impact the ddr interactive mode
- the registers of the param 'phy.cal' are initialized to 0 when
"st,phy-cal" is not present in device tree (default behavior when
DDR_PHY_CAL_SKIP is not activated)
- the info 'cal' field can be use to change the calibration behavior
- cal=1 => use param phy.cal to initialize the PHY, built-in training
is skipped
- cal=0 => param phy.cal is absent, built-in training is used (default)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
The STM32MP1 series is available in 3 different lines which are pin-to-pin
compatible:
- STM32MP157: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz,
3D GPU, DSI display interface and CAN FD
- STM32MP153: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz
and CAN FD
- STM32MP151: Single Cortex-A7 core, Cortex-M4 core @ 209 MHz
Each line comes with a security option (cryptography & secure boot)
& a Cortex-A frequency option :
- A : Cortex-A7 @ 650 MHz
- C : Secure Boot + HW Crypto + Cortex-A7 @ 650 MHz
- D : Cortex-A7 @ 800 MHz
- F : Secure Boot + HW Crypto + Cortex-A7 @ 800 MHz
This patch adds the support of STM32MP15xD and STM32MP15xF in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add BSEC lock access (read / write) at 0xC0000000 offset of misc driver.
The write access only available for Trusted boot mode, based on new
SMC STM32_SMC_WRLOCK_OTP.
With the fuse command, the permanent lock status is accessed with
0x10000000 offset (0xC0000000 - 0x8000000 for OTP sense/program
divided by u32 size), for example:
Read lock status of fuse 57 (0x39)
STM32MP> fuse sense 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
Set permanent lock of fuse 57 (0x39)
STM32MP> fuse prog 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
WARNING: the OTP lock is updated only after reboot
WARING: Programming lock or fuses is an irreversible operation!
This may brick your system.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
add DM/DTS support for the memory based bootcounter
in drivers/bootcount/bootcount.c.
Let the old implementation in, so boards which have
not yet convert to DM/DTS do not break.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for clock stretching to the i2c-gpio driver. This is
accomplished by switching the GPIO used for the SCL line to an input
when it should be driven high, and polling on the SCL line value until
it goes high (indicating that the I2C slave is no longer pulling it
low).
This is enabled by default; for gpios which cannot be configured as
inputs, the i2c-gpio,scl-output-only property can be used to fall back
to the previous behavior.
Signed-off-by: Michael Auchter <michael.auchter@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
U-Boot is having DT which doesn't cover all options currently supported by
driver. DT binding is aligned with Linux kernel version available here.
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ti,dp83867.txt
Based on my talk with Grygorii Strashko better will be to remove it.
Also Linux kernel bindings are being converted to yaml that's another
reason to do it only at one place.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
doc/README.drivers.eth seems like a good source for understanding
U-Boot's network subsystem, but is only talking about legacy network
drivers. This is particularly sad as proper documentation would help in
porting drivers over to the driver model.
Rewrite the document to describe network drivers in the new driver model
world. Most driver callbacks/methods are almost identical in their
semantic, but recv() differs in some important details.
Also keep some parts of the original text at the end, to help
understanding old drivers. Add some hints on how to port drivers over.
This also uses the opportunity to reformat the document in reST, on the
way moving it into doc/driver-model and adding it into the structure
there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The value for "Top of CAR region" should be fefc0000, not
fefc000. This matches the Kconfig default values, as
SYS_CAR_ADDR and SYS_CAR_SIZE are 0xfef00000 and 0xc0000
respectively.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Drop the Apollo Lake prefix 'apl' from the functions, types and
variables in the P2SB driver.
The P2SB is not Apollo Lake specific, and as such it was moved in
commit 2999846c11 ("x86: Move P2SB from Apollo Lake to a more generic
location") from the Apollo Lake folder to the intel_common folder.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Convert README to reStructuredText format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: spell out U-Boot correctly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
- add initial index for toradex boards reST documentation
- add initial colibri_imx7.rst doc file which provides all needed
information for obtaining a workable image ready for flashing
for both eMMC/NAND versions of Colibri iMX7.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: make title underline the same length as the title itself]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add device-tree binding documentation for ti framebuffer and generic
panel output driver.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ESM (Error Signal Monitor) is used on certain PMIC versions to
handle error signals propagating from rest of the system. If these
reach the PMIC, it is typically a last resort fatal error which
requires a system reset. The ESM driver does the proper configuration
for the ESM module to reach this end goal. Initially, only TPS65941
PMIC is supported for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The ESM (Error Signaling Module) is used to route error signals within
the K3 SoCs somewhat similar to interrupts. The handling for these is
different though, and can be routed for hardware error handling, to
be handled by safety processor or just as error interrupts handled
by the main processor. The u-boot level ESM driver is just used to
configure the ESM signals so that they get routed to proper destination.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Change plain test README to rst format and move this file
in documentation directory.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The load file 2 protocol can be used by the Linux kernel to load the initial
RAM disk. U-Boot can be configured to provide an implementation.
Add a description to the UEFI overview and document the related functions
in the API section.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Several patches delivered incorrect restructured text as documentation. We
should be able to discover this in Travis CI, Gitlab CI, or Azure CI.
So let us turn all build warnings into errors.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update doc/sphinx/kerneldoc.py from Linux next-20200219 to avoid warnings
like:
doc/sphinx/kerneldoc.py:125: RemovedInSphinx20Warning:
AutodocReporter is now deprecated. Use
sphinx.util.docutils.switch_source_input() instead.
self.state.memo.reporter =
AutodocReporter(result, self.state.memo.reporter)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl5GcB0ACgkQ4rK92eCq
k3Wr9gf/dDPJi6UBhLDio/IVKDBddOEUN0Lwdr9W0upL+DrdvEOyNyMSEKuLccIE
UTd1NmNNwcvgDRaPvB5o3R7twWItTW0cYlmVkFSZ228aq6xdf/SElN2OUD6B9Gh+
8bi6oVLu41TNMYn4VYxsEftcT2megfH8s+SH/FlvR5ua1yCC1vyrytEQjPIbJAB2
sa90ewDyp5EYqGLdAk6AVjPLeNZsaleGwuyLf04PoC2xhn+3HTEKJCJN4O46aJUr
0GUI7YN7pTjIfZdYfFqjcwoQV1xV2HtbjCTcOb8Td8TEYjIoILF8tSyfIwDXWGB5
zMQIQxUdQyNiqdBPFcnkAufjk+zLIQ==
=0dG+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
Fix the following DT dtc warnings for stm32mp1 boards:
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@0:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@1:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@2:
node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/rcc@50000000/st,pll@3:
node has a unit name, but no reg property
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Device tree and binding alignment with kernel v5.4
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Fix a build error
checking consistency...
/doc/board/rockchip/index.rst:
WARNING: document isn't included in any toctree
Fixes: 338b86c9b3 ("doc: boards: Add rockchip documentation")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
- Move P2SB from Apollo Lake to a more generic location
- Add a function to find a device by drvdata in DM core
- Enhancement of DM IRQ uclass driver
- Add a clock driver for Intel devices
- Add support for ACPI general-purpose events
- Add a TPM driver for H1/Cr50
- Enable TPM on Google Chromebook Coral
OpenSBI build steps are marked as normal text in
AX25-AE350 documentation.
Move them into code-block so-that it can show it
as build steps.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Assign Alex Nemirovsky as custodian for all
Cortina Access (CA) for ARM and MIPS based SoCs.
Currently Cortina Access CAxxxx family of SoCs support both
ARM and MIPS ISA. Drivers have cross platform support for
both architectures.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Use the correct return value in function do_gpio() and update
commands documentation with the return values from command_ret_t enum.
CMD_RET_SUCCESS is returned on command success and CMD_RET_FAILURE is
returned on command failure.
The command was returning the pin value, which caused confusion when
debugging (#define DEBUG).
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Tested-by: Robert Marko <robert.marko@sartura.hr>
ACPI GPEs are used to signal interrupts from peripherals that are accessed
via ACPI. In U-Boot these are modelled as interrupts using a separate
interrupt controller. Configuration is via the device tree.
Add a simple driver for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present driver model supports the IRQ uclass but there is no way to
request a particular interrupt for a driver.
Add a mechanism, similar to clock and reset, to read the interrupts
required by a device from the device tree and to request those interrupts.
U-Boot itself does not have interrupt-driven handlers, so just provide a
means to read and clear an interrupt. This can be useful to handle
peripherals which must use an interrupt to determine when data is
available, for example.
Bring over the basic binding file as well, from Linux v5.4. Note that the
older binding is not supported in U-Boot; the newer 'special form' must be
used.
Add a simple test of the new functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a new device-tree property to control the colour depth. At present we
support 16bpp and 32bpp.
While we are here, update the code to use livetree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Sandbox currently uses SDL1.2. SDL2 has been around for quite a while and
is widely supported. It has a number of useful features. It seems
appropriate to move sandbox over.
Update the code to use SDL2 instead of SDL1.2.
Signed-off-by: Simon Glass <sjg@chromium.org>
Following the recommendation of adding '#define DEBUG' at the top
of drivers/core/lists.c does not cause the debug messages to be
shown. Change it to '#define LOG_DEBUG' instead, which actually
makes it work as per doc/README.log.
While at it, provide the full path to lists.c to in order to make
the instructions clearer.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is convenient for bloblist to zero out the contents of a records when
it is added. This saves the callers having to do it.
Update the API accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Various minor fixes for x86
- Switch to ACPI mode on Intel edison
- Support run-time configuration for NS16550 driver
- Update coreboot and slimbootloader serial drivers to use NS16550
run-time configuration
- ICH SPI driver fixes to hardware sequencing erase case
- Move ITSS from Apollo Lake to a more generic location
- Intel GPIO driver bug fixes
- Move to vs2017-win2016 platform build host for Azure pipelines
Convert Android documentation from regular txt format to Sphinx (RST).
Also add Android index.rst file and reference it in root index.rst, so
that Android documentation is visible.
Test:
$ make htmldocs
$ xdg-open doc/output/index.html
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Describe Android Boot Image format, how its support is implemented in
U-Boot and associated commands usage.
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use valid restructured text to avoid warnings like
WARNING: Title underline too short.
WARNING: Block quote ends without a blank line; unexpected unindent.
when building with `make htmldocs`.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Now, Slim Bootloader uses NS16550_DYNAMIC to support serial port
configuration at runtime, so no more code change is required.
Therefore, remove unnecessary steps and fix minor typo.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Rockchip has documentation file, doc/README.rockchip but
which is not so readable to add or understand the existing
contents. Even the format that support is legacy readme
in U-Boot.
Add rockchip specific documentation file using new rst
format, which describes the information about Rockchip
supported boards and it's usage steps.
Added minimal information about rk3288, rk3328, rk3368
and rk3399 boards and usage. This would indeed updated
further based on the requirements and updates.
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Take over TI maintainership from Tom.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use
macros such as CONFIG_IS_ENABLED() that allow conditional compilation of
code for SPL and U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
DS3232 is an i2c RTC with 236 bytes of battery-backed SRAM.
Add an RTC driver for DS3232 device, which provides time and
date support. Also read and write functions are provided,
which can be used to access the SRAM memory.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
This patch adds a new section "Launching a UEFI binary from a FIT image"
documenting the usage of the CONFIG_BOOTM_EFI extension to bootm command
that offers a verified boot alternative for UEFI binaries such as GRUB2.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch adds an example FIT image description file demonstrating
the usage of bootm command to securely launch UEFI binaries.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When the `dfu` command is called from the U-Boot environment,
it now accepts an optional parameter that specifies a timeout (in seconds).
If a DFU connection is not made within that time the `dfu` command exits
(as it would if Ctrl+C was pressed). If the timeout is left empty or being
zero the `dfu` command behaves as it does now.
This is useful for allowing U-Boot to check to see if anything wants to
upload new firmware before continuing to boot.
The patch is based on the commit
5e966ccc3c
by Sebastien Colleur, which has been heavily reworked due to U-Boot changes
in the past.
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Add documentation about packing optional second level boot-loader with
mkimage tool.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The defconfig file for ROC-CC-RK3308 is roc-cc-rk3308_defconfig.
Fixes: 7f08bfb74f ("doc: rockchip: Add documentation for rk3308 based
boards")
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for coral which is a range of Apollo Lake-based Chromebook
released in 2017. This also includes reef released in 2016, since it is
based on the same SoC.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a GPIO driver which uses the pinctrl driver to access the pad
information. This driver relies on the GPIO nodes being subnodes to the
pinctrl device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Recent Intel SoCs share a pinctrl mechanism with many common elements. Add
an implementation of this core functionality, allowing SoC-specific
drivers to avoid adding common code.
As well as a pinctrl driver this provides a GPIO driver based on the same
code.
Once other SoCs use this driver we may consider moving more properties to
the device tree (e.g. the community info and pad definitions).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't want to include dt-structs.h in header files, so add a note about
that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present PCI auto-configuration happens in U-Boot both before and after
relocation. This is a waste of time and may mess up static addresses used
in board_init_f(). Adjust the code to supporting doing auto-configuration
once, after relocation, under control of a device-tree property.
This is needed for Apollo Lake for debugging the silicon-init code. Once
the UART is moved to a different MMIO address the debug UART does not work
and any debug output in Apollo Lake's arch_fsp_init_r() causes a hang.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Describe that a signature node can be added to a binary device tree using
the mkimage tool.
Provide an example device tree node.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Commit 656d8da9d2 (doc: Remove duplicated documentation directory) got
rid of most of Documentation/. But there's still an obviously useless
.gitignore left behind.
Also, there's a copy of the linux kernel's net/ethernet.txt binding
imported from v5.0, while the existing one in doc/ is from 4.0-rc1. So
replace the latter by the former, and making Documentation/ finally
empty.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
- Increase stack size to avoid a stack overflow during distro boot.
- Add hifive-unleashed-a00.dts for SIFIVE FU540.
- Add OF_SEPARATE support for SIFIVE FU540.
- Add SPL support for Andes AX25 AE350.
- Improve U-Boot SPL / OpenSBI smp boot flow for RISC-V.
Add descriptions about U-Boot SPL feature and how to build and run.
Signed-off-by: Rick Chen <rick@andestech.com>
Cc: KC Lin <kclin@andestech.com>
Cc: Alan Kao <alankao@andestech.com>
This would help to make the necessary changes in drivers and device trees
in U-Boot tree itself. This feature would also be helpful to not pass
dtb during opensbi builds.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Rick Chen <rick@andestech.com>
A couple of optional properties have been introduced for Aquantia PHY
allowing the driver to set up wiring related configuration points that
are otherwise driven by firmware.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
It defines that PHY nodes must be children on MDIO bus nodes and defines
the only required property in U-Boot, reg. This property along with the
example provided are copied over from Linux.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Based on commit 980066e6d964 ("dt-bindings: phy: dp83867: Add documentation
for disabling clock output") of mainline linux kernel.
The clock output is generally only used for testing and development and not
used to daisy-chain PHYs. It's just a source of RF noise afterward.
Add a mux value for "off". I've added it as another enumeration to the
output property. In the actual PHY, the mux and the output enable are
independently controllable. However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.
Document that PHY's default setting will be left as is if the property
is omitted.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Part of the env cleanup moved this out of the environment code and into
the net code. However, this helper is sometimes needed even when the net
stack isn't included.
Move the helper to lib/net_utils.c like it's similarly-purposed
string_to_ip(). Also rename the moved function to similar naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Ondrej Jirman <megous@megous.com>
After commit d8765e2422 ("Enable building of u-boot.itb
on Rockchip platform"), u-boot.itb will automatically
generated by "make all" command, manually command
"make u-boot.itb" is no longer needed.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enhance do_bootm_vxworks() to support Linux compatible standard DTB
for ARM and PPC, when the least significant bit of flags in VxWorks
bootargs is set. Otherwise it falls back to the existing bootm flow
which is now legacy.
Signed-off-by: Lihua Zhao <lihua.zhao@windriver.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
Rename the CONFIG_SECURE_BOOT name to CONFIG_NXP_ESBC to avoid
conflicts with UEFI secure boot.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a note about the driver name in the of-platdata documentation since
the naming must follow the compatible string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add optional parameter to 'avb verify' sub-command, so that user is able
to specify which slot to use, in case when user's partitions are
slotted. If that parameter is omitted, the behavior of 'avb verify' will
be the same as before, so user API is content.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Acked-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Add weak callback to allow board specific behavior
- flush
- initiated
This patch prepare usage of DFU back end for communication with
STM32CubeProgrammer on stm32mp1 platform with stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a virtual DFU backend to allow board specific read and write
(for OTP update for example).
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add the support of MTD partition for the MTD backend.
The expected dfu_alt_info for one alternate on the mtd device :
<name> part <part_id>
<name> partubi <part_id>
"partubi" also erase up to the end of the partition after write operation.
For example: dfu_alt_info = "spl part 1;u-boot part 2; UBI partubi 3"
U-Boot> dfu 0 mtd nand0
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add DFU backend for MTD device: allow to read
and write on all MTD device (NAND, SPI-NOR,
SPI-NAND,...)
For example :
> set dfu_alt_info "nand_raw raw 0x0 0x100000"
> dfu 0 mtd nand0
This MTD backend provides the same level than dfu nand
backend for NAND and dfu sf backend for SPI-NOR;
So it can replace booth of them but it also
add support of spi-nand.
> set dfu_alt_info "nand_raw raw 0x0 0x100000"
> dfu 0 mtd spi-nand0
The backend code is based on the "mtd" command
introduced by commit 5db66b3aee ("cmd: mtd:
add 'mtd' command")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of DFU for several interface/device
with one command.
The format for "dfu_alt_info" in this case is :
- <interface> <dev>'='alternate list (';' separated)
- each interface is separated by '&'
The previous behavior is always supported.
One example for NOR (bootloaders) + NAND (rootfs in UBI):
U-Boot> env set dfu_alt_info \
"sf 0:0:10000000:0=spl part 0 1;u-boot part 0 2; \
u-boot-env part 0 3&nand 0=UBI partubi 0,3"
U-Boot> dfu 0 list
DFU alt settings list:
dev: SF alt: 0 name: spl layout: RAW_ADDR
dev: SF alt: 1 name: ssbl layout: RAW_ADDR
dev: SF alt: 2 name: u-boot-env layout: RAW_ADDR
dev: NAND alt: 3 name: UBI layout: RAW_ADDR
U-Boot> dfu 0
$> dfu-util -l
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=3, name="UBI", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=2, name="u-boot-env", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=1, name="u-boot", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=0, name="spl", serial="002700333338511934383330"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Copy the partition support from NAND backend to SF,
support part and partubi option.
In case of ubi partition, erase the rest of the
partition as it is mandatory for UBI.
The added code is under compilation flag CONFIG_DFU_SF_PART
activated by default.
for example:
U-Boot> env set dfu_alt_info "spl part 0 1;\
u-boot part 0 2;u-boot-env part 0 3;UBI partubi 0 4"
U-Boot> dfu 0 sf 0:0:10000000:0
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This adds a reST document for how to build U-Boot host tools,
including information for both Linux and Windows.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
We need distinguish the following two situations in various SPI APIs:
- given chip select num is invalid
- given chip select num is valid, but no device is attached
Currently -ENODEV is returned for both cases.
For the first case, it's more reasonable to return -EINVAL instead of
-ENODEV for invalid chip select numbers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
If an SPI controller driver does not implement ops->cs_info, that
probably means any chip select number could be valid, hence let's
return 0 for spi_cs_info().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
ubi enhancements for 2020.01
- provide a way for skipping crc checks ported from linux, and add an
U-Boot command to set this flag on already installed systems.
- fix redundand environment management
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl2l20YACgkQfxc6PpAI
reZQQQgA0zxySnZR6IuTr+MXJP019SjU0T/rj2Ob77ODhLTtLtE3aFYgBIsyyOyr
/NZ6V7wPhCfGGBGWdPzYdOUIkG5L4O+1zrwWGgVJCAAaCaDlJVIXmljJ667SE9ps
9jfJW/nkzgsa/cOweOUJF3vBUKnDN1pv9aTXwAXttzv/OqaZ1AaUObnmeZ9fzr65
mXjR7/eLYx26KQ8IEo8hhgdFhN/d/aUtSCYPWASqtcI9TLg8A5gmtNxy83+w8gzC
kFIr7c0QjZ3EQHLyD4/MAcGvhZZMBPbV6dyIO19hUS80S1l1yMTd72iTYuvG8bAt
5TzlQCSqvGryF6TRxVn8GPr2/T0v/A==
=Oo/D
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-15oct19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
binman enhancements:
- Dropping some test Elf files and building them from source instead
- Refactoring of x86 16-bit entries
- Support for SPL symbols within sections
- Handle the 'notes' sections and hidden symbols in recent binutils
- Improved error reporting with a tool fails
libfdt and documentation fixes
vboot required-key test
driver model power-domain controls
patman Message-Id enhancement
Fully take over the ARM maintainers entry.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
U-Boot now supports the "skip_check" flag to optionally skip the CRC
check at open time. Currently its only possible to set this bit upon
UBI volume creation. But it might be very useful to also set this bit
on already installed systems (e.g. field upgrade) to make also use of
the boot-time decrease on those systems.
This patch now adds a new "ubi" command "ubi skipcheck" to set or clear
this bit in the UBI volume header:
=> ubi skipcheck rootfs0 on
Setting skip_check on volume rootfs0
BTW: This saves approx. 10 seconds Linux bootup time on a MT7688 based
target with 128MiB of SPI NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
At this point, all drivers that do not use CONFIG_BLK are past their
migration deadlines, so remove this config as it's no longer helpful and
hinders enhancing block drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for CDCE913/925/937/949 family of devices. These are modular
PLL-based low cost, high performance, programmable clock synthesizers,
multipliers and dividers. They generate up to 9 output clocks from a
single input frequency. The initial version of the driver does not
support programming of the PLLs, and thus they run in the bypass mode
only. The code is loosely based on the linux kernel cdce9xx driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This adds a document for tphy which supports physical layer
functionality for a number of controllers on MediaTek SoCs,
such as, USB2.0, USB3.0, PCIe, and SATA.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This adds a document for MT7623 PCIe controller.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Some Texas Instruments K3 family of SoCs have one of more Digital Signal
Processor (DSP) subsystems that are comprised of either a TMS320C66x
CorePac and/or a next-generation TMS320C71x CorePac processor subsystem.
Add the device tree bindings document for the C66x DSP devices on these
SoCs. The added example illustrates the DT nodes for the first C66x DSP
device present on the K3 J721E family of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The Texas Instruments K3 family of SoCs have one of more dual-core
Arm Cortex R5F processor subsystems/clusters (R5FSS). Add the device
tree bindings document for these R5F subsystem devices. These R5F
processors do not have an MMU, and so require fixed memory carveout
regions matching the firmware image addresses. The nodes require more
than one memory region, with the first memory region used for DMA
allocations at runtime. The remaining memory regions are reserved
and are used for the loading and running of the R5F remote processors.
The added example illustrates the DT nodes for the single R5FSS device
present on K3 AM65x family of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Devicetree bindings are already specified in Linux kernel documentation.
Instead of maintaining same dt bindings in U-Boot doc specify path to dt
bindings in Linux kernel & documenting specific changes that are in U-Boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Fix these spelling errors the header file and documentation.
Fix a small typo in the PCI documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sandbox pci works using emulation drivers which are currently children of
the pci device:
pci-controller {
pci@1f,0 {
compatible = "pci-generic";
reg = <0xf800 0 0 0 0>;
emul@1f,0 {
compatible = "sandbox,swap-case";
};
};
};
In this case the emulation device is attached to pci device on address
f800 (device 1f, function 0) and provides the swap-case functionality.
However this is not ideal, since every device on a PCI bus has a child
device. This is only really the case for sandbox, but we want to avoid
special-case code for sandbox.
Worse, child devices cannot be probed before their parents. This forces
us to use 'find' rather than 'get' to obtain the emulator device. In fact
the emulator devices are never probed. There is code in
sandbox_pci_emul_post_probe() which tries to track when emulators are
active, but at present this does not work.
A better approach seems to be to add a separate node elsewhere in the
device tree, an 'emulation parent'. This could be given a bogus address
(such as -1) to hide the emulators away from the 'pci' command, but it
seems better to keep it at the root node to avoid such hacks.
Then we can use a phandle to point from the device to the correct
emulator, and only on sandbox. The code to find an emulator does not
interfere with normal pci operation.
Add a new UCLASS_PCI_EMUL_PARENT uclass which allows finding an emulator
given a bus, and finding a bus given an emulator. Update the existing
device trees and the code for finding an emulator.
This brings PCI emulators more into line with I2C.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix 3 typos in the commit message;
encode bus number in the labels of swap_case_emul nodes;
mention commit 4345998ae9 in sandbox_pci_get_emul()]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot already supports using -D to indicate that it should use the normal
device tree. It is sometimes useful to run with the test device tree, e.g.
when running a test. Add a -T option for this along with some
documentation.
It can be used like this:
/tmp/b/sandbox/u-boot -T -c "ut dm pci_busdev"
(this will use /tmp/b/sandbox/arch/sandbox/dts/test.dtb as the DT)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Sometimes devices don't appear and it can be confusing. Add a few notes to
help with this situation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix 2 issues in the doc and include the doc in the index.rst]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This updates MAINTAINERS and git-mailrc to add me as maintainer for
socfpga.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
For many sub-systems we already require the driver model to be used. Yet
there is still a handful of boards that do not have CONFIG_DM enabled.
We should make CONFIG_DM compulsory with release v2020.01
Conversion dates for CONFIG_DM_SPL and CONFIG_DM_TPL are yet to be defined.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The README.scrapyard file has been inconsistently updated. While well
intentioned, bad data is worse than no data, and in this case a pointer
to use the history that git provides. Remove the current content and
the script that would update it from time to time as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
The of-plat.rst file till this change has been using
This is at best misleading as SPL_OF_PLATDATA is always defined when we
want to use this SPL tinification feature (also in U-Boot proper).
As a result the OF_PLATDATA SPL specific code is also compiled in when
U-Boot proper is build.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add steps to test Linux booting on QEMU with Yocto image.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
-----BEGIN PGP SIGNATURE-----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=hWTf
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-boot
- fix mailbox status register used for polling
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
The driver model has been supported for network drivers since 2015. It is
time to convert the remaining boards. Set July 2020 as a timeline.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a separate driver for the MDIO interface of the
Marvell Ethernet controllers based on driver model. There are two
reasons to have a separate driver rather than including it inside
the MAC driver itself:
*) The MDIO interface is shared by all Ethernet ports, so a driver
must guarantee non-concurrent accesses to this MDIO interface. The
most logical way is to have a separate driver that handles this
single MDIO interface, used by all Ethernet ports.
*) The MDIO interface is the same between the existing mv643xx_eth
driver and the new mvneta/mvpp2 driver. Even though it is for now
only used by the mvneta/mvpp2 driver, it will in the future be
used by the mv643xx_eth driver as well.
This driver supports SMI IEEE for 802.3 Clause 22 and XSMI for IEEE
802.3 Clause 45.
This patch also adds device tree binding for marvell MDIO driver.
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a binding document for mdio. A notable deviation from corresponding
Linux binding is the introduction of device-name optional property, which
can be used to name MDIO buses. Two reset optional properties described
by Linux binding are also not present as they don't seem to be used in
U-Boot at this time.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The available defconfigs for RISC-V QEMU have changed. We now have
configurations to compile U-Boot to run in supervisor mode and for
U-Boot SPL. Update the QEMU RISC-V documentation to reflect these
changes.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Some boards have coded this offset with formula or bitshifts in their
board-config. Manually convert these things into hex-values to be able
using moveconfig.py afterwards.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Correctly reference uefi/uefi.rst and uefi/u-boot_on_efi.rst.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Avoid a warning when building the 'make htmldocs' target:
doc/board/intel/slimbootloader.rst:90: WARNING: Title underline too short.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
We should explicitly load DTB from TFTP server or MMC/SD card
for Linux booting. This will allow us:
1. To use different Linux DTB for SiFive Unleashed board with
expansion board connected.
2. Avoid re-flashing OpenSBI firmware whenever board connections
change.
This patch updates reference bootlog in SiFive FU540 README
as-per above.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
- Enable SD slot on Intel Edison
- Populate CSRT ACPI table for shared DMA controller on Intel Tangier
- Convert Intel ICH-SPI driver to use new spi-mem ops
- Enable config_distro_bootcmd for QEMU x86
- Support U-Boot as a payload for Intel Slim Bootloader
- Avoid writing temporary asl files into the source tree which fixes the
parallel build issue occasionally seen
For U-Boot we allow a GPIO to be specified to enable the codec. Add this
to the relevant binding files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
