Commit graph

164 commits

Author SHA1 Message Date
Haiying Wang
c013b74975 NAND: Add support for MPC8572DS board
This patch defines 1M TLB&LAW size for NAND on MPC8572DS, assigns
0xffa00000 for CONFIG_SYS_NAND_BASE and adds other NAND supports in
config file.

It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image, to
make room for the increased code size with NAND enabled.

Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-29 13:08:17 -05:00
Kumar Gala
2dba0dea98 85xx: Convert all fsl_pci_init users to new APIs
Converted ATUM8548, MPC8536DS, MPC8544DS, MPC8548CDS, MPC8568MDS,
MPC8572DS, TQM85xx, and SBC8548 to use fsl_pci_setup_inbound_windows()
and ft_fsl_pci_setup().

With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
2008-10-24 17:35:12 -05:00
Kumar Gala
0151cbaccf 85xx: Enable 64-bit PCI resources on all Freescale boards
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
2008-10-24 17:33:06 -05:00
Dave Liu
d5b693090e 85xx: remove unused config definition
Signed-off-by: Dave Liu <daveliu@freescale.com>
2008-10-24 16:18:33 -05:00
Liu Yu
7e183cad0c Enabled the Freescale SGMII riser card on 8572DS
This patch based on Andy's work.
Including command 'pixis_set_sgmii' support.

Signed-off-by: Liu Yu <yu.liu@freescale.com>
2008-10-18 21:54:07 +02:00
Haiying Wang
4ca06607d6 Add ddr interleaving suppport for MPC8572DS board
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.

* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.

* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.

* Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2008-10-18 21:54:05 +02:00
Kumar Gala
1c9aa76bf9 85xx: Enable interrupt and setexpr commands on Freescale 85xx boards
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-18 21:54:04 +02:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Kumar Gala
f3bf927393 MPC8572DS: Fix compile warnings
Commit 445a7b3830 introduced the following
compile warnings:

cmd_i2c.c:112: warning: missing braces around initializer
cmd_i2c.c:112: warning: (near initialization for 'i2c_no_probes[0]')

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-10-08 15:43:28 -05:00
Haiying Wang
445a7b3830 Add ID EEPROM support for MPC8572DS
The ID EEPROM on MPC8572DS board locates on I2C bus 1. Its the storage for
system information like mac addresses etc. This patch enables it.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2008-10-07 16:22:26 -05:00
Haiying Wang
1f3ba317a5 Minor fixes for I2C address on MPC8572DS
MPC8572DS has two i2c buses. This patch moves the DDR SPD_EEPROM to i2c bus 1
according to the board spec, and adds the 2nd i2c bus offset.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
2008-10-07 16:22:22 -05:00
Jean-Christophe PLAGNIOL-VILLARD
0e8d158664 rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:06 +02:00
Jean-Christophe PLAGNIOL-VILLARD
5a1aceb068 rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASH
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:04 +02:00
Kumar Gala
129ba616b3 mpc85xx: Add support for the MPC8572DS reference board
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-08-27 11:43:53 -05:00