addon 183923d3e
MMC/SATA have no erase blocks, only blocks. Hence the warning
about erase block alignment might be confusing in such environment.
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For double buffering to work, the target buffer must always be big
enough to hold all data. This can only be ensured if buffers are of
equal size, otherwise one must be smaller and we risk data loss
when copying from the bigger to the smaller buffer.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
56086921 added support for unaligned environments access.
U-boot itself does not support this:
- env_nand.c fails when using an unaligned offset. It produces an
error in nand_erase_opts{drivers/mtd/nand/nand_util.c}
- in env_sf/env_flash the unused space at the end is preserved, but
not in the beginning. block alignment is assumed
- env_sata/env_mmc aligns offset/length to the block size of the
underlying device. data is silently redirected to the beginning of
a block
There is seems no use case for unaligned environment. If there is
some useful data at the beginning of the the block (e.g. end of u-boot)
that would be very unsafe. If the redundant environments are hosted by
the same erase block then that invalidates the idea of double buffering.
It might be that unaligned access was allowed in the past, and that
people with legacy u-boot are trapped. But at the time of 56086921
it wasn't supported and due to reasons above I guess it was never
introduced.
I prefer to remove that (unused) feature in favor of simplicity
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Format warnings (-Wformat) were shown in printf() calls after defining
DEBUG macro.
Update format string and explicitly cast variables to suppress all
warnings.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Try to avoid adhoc iteration of the environment. Reuse fw_getenv
to find the variables that should be printed. Only use open-coded
iteration when printing all variables.
For backwards compatibility, keep emitting a newline when
printing with value_only.
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
forward declaration not needed when re-ordered
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
there are two groups of functions:
- application ready tools: fw_setenv/fw_getenv/fw_parse_script
these are used, when creating a single binary containing multiple
tools (busybox like)
- file access like: open/read/write/close
above functions are implemented on top of these. applications
can use those to modify several variables without creating a
temporary batch script file
tested with "./scripts/kernel-doc -html -v tools/env/fw_env.h"
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
A negative value for the offset is treated as a backwards offset for
from the end of the device/partition for block devices. This aligns
the behavior of the config file with the syntax of CONFIG_ENV_OFFSET
where the functionality has been introduced with
commit 5c088ee841 ("env_mmc: allow negative CONFIG_ENV_OFFSET").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Currently flash_read completes a crucial part of the environment
device configuration, the device type (mtd_type). This is rather
confusing as flash_io calls flash_read conditionally, and one might
think flash_write, which also makes use of mtd_type, gets called
before flash_read. But since flash_io is always called with O_RDONLY
first, this is not actually the case in reality.
However, it is much cleaner to complete and verify the config early
in parse_config. This also prepares the code for further extension.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Andreas Fenkart
If users of the library are happy with the default, e.g. config file
name. They can pass NULL as the opts pointer. This simplifies the
transition of existing library users.
FIXES a compile error. since common_args has been removed by
a previous patch
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
checkpatch complains about in succeding patch. Prefer to fix all
declarations in a dedicated patch.
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
env library is broken as the config file pointer is only initialized
in main(). When running in the env library parse_config() fails:
Cannot parse config file '(null)': Bad address
Ensure that config file pointer is always initialized.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
fw_senten/fw_printenv can be compiled as a tools library,
excluding the fw_env_main object.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
disabled original parsing, but not yet removed since the
argument indexing needs to be fixed
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
goal is to use getopt for all argument parsing instead of adhoc
parsing in fw_getenv/fw_setenv functions
Signed-off-by: Andreas Fenkart <andreas.fenkart@digitalstrom.com>
With gcc 5.2 and later we get a bunch of "error: unknown type name" for
'uint8_t', 'uint32_t' and friends.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Sometimes it can be useful to link the fw_ tools instead
of having the fw_setenv/fw_printenv installed.
Patch exports the tool as library and allowes to link it
with own programs.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When for example generating/manipulating SD card/eMMC images which
contain U-Boot and its environment(s), it is handy to use a given
configuration file instead of the compiled-in default one.
And since the default configuration file is expected under /etc
it's hard for an usual linux user account without special permissions
to use fw_printenv/fw_setenv for this purpose.
So allow to pass an optional filename via a new '-c' command
line argument.
Example:
$ ln -s fw_printenv tools/env/fw_setenv
$ cat fw_env.config
test.img 0x20000 0x20000
test.img 0x40000 0x20000
$ tools/env/fw_printenv -c ./fw_env.config fdt_file
fdt_file=imx28-duckbill.dtb
$ tools/env/fw_setenv -c ./fw_env.config fdt_file imx28-duckbill-spi.dtb
$ tools/env/fw_printenv -c ./fw_env.config fdt_file
fdt_file=imx28-duckbill-spi.dtb
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
When building tools-only (or env) we need to be sure that we do use
<linux/kconfig.h> and do not use <generated/autoconf.h>. This will fix
problems such as running 'make defconfig' or 'make sandbox_config' and
then 'make tools-only'.
Based on the responses below to the thread add linux/kconfig.h higher in
the includes and drop the now unneeded autoconf.h lower down to ensure
the default environment is included correctly
http://lists.denx.de/pipermail/u-boot/2015-June/216849.html
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
This patch fixes cross-compiling U-Boot tools with the musl C library:
* including <sys/types.h> is needed for ulong
* defining _GNU_SOURCE is needed for loff_t
Tested for target at91sam9261ek_dataflash_cs3.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Cc: Tom Rini <trini@konsulko.com>
Without this, when CONFIG_ENV_VARS_UBOOT_CONFIG is active we get
a compile time error when doing 'make env'.
In file included from tools/env/fw_env.c:117:0:
include/env_default.h:110:11: error: expected ‘}’ before ‘CONFIG_SYS_ARCH’
When building U-Boot this is included indirectly by the compiler switch
-include
/home/trdx/git.toradex.com/u-boot-2014.10-toradex/include/linux/kconfig.h
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
For example on a raspberry pi the u-boot environment can be
saved in a file on the first VFAT partition.
This example illustrates how to use it with fw_printenv/fw_setenv.
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
On architectures where 'long' is 64 bit, the u-boot environment
as seen by the fw_env tools was missing 4 bytes.
This patch fixes getenvsize(), and thus also ensures that the
environment's CRC32 checksum is calculated correctly.
Signed-off-by: Dominic Sacré <dominic.sacre@gmx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
When building the U-Boot tools for non-ELF platforms (such as Blackfin
FLAT), since commit 79fc0c5f49
("tools/env: cross-compile fw_printenv without setting HOSTCC"), the
build fails because it tries to strip a FLAT binary, which does not
make sense.
This commit solves this by changing the stripping logic in
tools/env/Makefile to be similar to the one in tools/Makefile. This
logic continues to apply strip to the final binary, but does not abort
the build if it fails, and does the stripping in place on the final
binary. This allows the logic to work fine if stripping doesn't work,
as it leaves the final binary untouched.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Sonic Zhang <sonic.zhang@analog.com>
This commit enables Kconfig.
Going forward, we use Kconfig for the board configuration.
mkconfig will never be used. Nor will include/config.mk be generated.
Kconfig must be adjusted for U-Boot because our situation is
a little more complicated than Linux Kernel.
We have to generate multiple boot images (Normal, SPL, TPL)
from one source tree.
Each image needs its own configuration input.
Usage:
Run "make <board>_defconfig" to do the board configuration.
It will create the .config file and additionally spl/.config, tpl/.config
if SPL, TPL is enabled, respectively.
You can use "make config", "make menuconfig" etc. to create
a new .config or modify the existing one.
Use "make spl/config", "make spl/menuconfig" etc. for spl/.config
and do likewise for tpl/.config file.
The generic syntax of configuration targets for SPL, TPL is:
<target_image>/<config_command>
Here, <target_image> is either 'spl' or 'tpl'
<config_command> is 'config', 'menuconfig', 'xconfig', etc.
When the configuration is done, run "make".
(Or "make <board>_defconfig all" will do the configuration and build
in one time.)
For futher information of how Kconfig works in U-Boot,
please read the comment block of scripts/multiconfig.py.
By the way, there is another item worth remarking here:
coexistence of Kconfig and board herder files.
Prior to Kconfig, we used C headers to define a set of configs.
We expect a very long term to migrate from C headers to Kconfig.
Two different infractructure must coexist in the interim.
In our former configuration scheme, include/autoconf.mk was generated
for use in makefiles.
It is still generated under include/, spl/include/, tpl/include/ directory
for the Normal, SPL, TPL image, respectively.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
We currently limit ourself to 16 characters for the device name to read
the environment from. This is insufficient for /dev/mmcblk0boot1 to
work for example. Switch to '%ms' which gives us a dynamically
allocated buffer instead. We're short lived enough to not bother
free()ing the buffer.
Signed-off-by: Tom Rini <trini@ti.com>
Implement support for encrypting/decrypting the environment block
into the tools/env/fw_* tools. The cipher used is AES 128 CBC and
the implementation depends solely on components internal to U-Boot.
To allow building against the internal AES library, the library did
need minor adjustments to not include U-Boot's headers which are not
wanted to be included and define missing types.
Signed-off-by: Marek Vasut <marex@denx.de>
Prior to Kbuild, $(TOPDIR) or $(SRCTREE) was used for
pointing to the top of source directory.
(No difference between the two.)
In Kbuild style, $(srctree) is used for instead.
This commit renames SRCTREE to srctree and deletes the
defition of SRCTREE.
Note that SRCTREE in scripts/kernel-doc, scripts/docproc.c,
doc/DocBook/Makefile should be keep.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Some NOR flash devices have a small erase block size. For example, the
Micron N25Q512 can erase in 4K blocks. These devices expose a bug in
fw_env.c where flash_write_buf() incorrectly calculates bytes written
and attempts to write past the environment sectors. Luckily, a range
check prevents any real damage, but this does cause fw_setenv to fail
with an error.
This change corrects the write length calculation.
The bug was introduced with commit 56086921 from 2008 and only affects
configurations where the erase block size is smaller than the total
environment data size.
Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com>
The assumed number of environment sectors (always 1) leads to an
incorrect top_of_range calculation in fw.env.c when a flash device has
an erase block size smaller than the environment data size (number of
environment sectors > 1).
This change updates the default number of environment sectors to at
least cover the size of the environment.
Also corrected a false statement about the number of sectors column in
fw_env.config.
Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com>
fw_printenv is a program which mostly runs on the target Linux.
Before switching to Kbuild, we needed to set HOSTCC at the
command line like this:
make HOSTCC=<your CC cross-compiler> env
Going forward we can cross compile it by specifying CROSS_COMPILE:
make CROSS_COMPILE=<your cross-compiler prefix> env
This looks more natural.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
This commit merges commonly-used header include paths
to UBOOTINCLUDE and NOSTDINC_FLAGS variables, which are placed
at the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Before this commit, makefiles under tools/ directory
were implemented with their own way.
This commit refactors them by using "hostprogs-y" variable.
Several C sources have been added to wrap other C sources
to simplify Makefile.
For example, tools/crc32.c includes lib/crc32.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
