Commit graph

4608 commits

Author SHA1 Message Date
Wolfgang Denk
4212657c53 Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
* 'master' of git://git.denx.de/u-boot-ppc4xx:
  powerpc/ppc4xx: Remove typedefs for gdsys FPGA
  powerpc/ppc4xx: Fix typo in gdsys_fpga.h
  powerpc/ppc4xx: Update gdsys board configurations
  powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
  powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
  powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
  powerpc/ppc4xx: Adjust environment size on neo
2012-04-30 16:55:25 +02:00
Wolfgang Denk
5f6db68b42 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
  powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
  cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
  PowerPC: correct the SATA for p1/p2 rdb-pc platform
  powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
  powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
  powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
  powerpc/corenet_ds: Slave module for boot from SRIO
  powerpc/corenet_ds: Master module for boot from SRIO
  powerpc/corenet_ds: Document for the boot from SRIO
  powerpc/corenet_ds: Correct the compilation errors about ENV
  powerpc/srio: Rewrite the struct ccsr_rio
  powerpc/85xx:Fix lds for nand boot debug info
  powerpc/p2041rdb: add env in NAND support
  powerpc/p2041rdb: add NAND and NAND boot support
  powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
  powerpc/85xx:Avoid vector table compilation for nand_spl
  powerpc/85xx:Fix IVORs addr after vector table relocation
  powerpc/85xx:Avoid hardcoded vector address for IVORs
  powerpc/p1023rds: Disable nor flash node and enable nand flash node
2012-04-30 16:45:56 +02:00
Wolfgang Denk
04a9cb8c59 Merge branch 'master' of git://git.denx.de/u-boot-i2c
* 'master' of git://git.denx.de/u-boot-i2c:
  i2c:designware Turn off the ctrl when setting the speed
  i2c: Add support for designware i2c controller
  sh: i2c: Add support I2C controller of SH7734
2012-04-30 16:43:49 +02:00
Wolfgang Denk
4868049309 Merge branch 'master' of git://git.denx.de/u-boot-nds32
* 'master' of git://git.denx.de/u-boot-nds32:
  board/adp-ag102: add configuration of adp-ag102
  board/adp-ag102: add board specific files
  nds32/ag102: add ag102 soc support
  nds32/ag102: add header support of ag102 soc
2012-04-30 16:29:16 +02:00
Dirk Eibach
996d88d810 powerpc/ppc4xx: Update gdsys board configurations
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30 15:01:17 +02:00
Dirk Eibach
2ade7bee15 powerpc/ppc4xx: Support gdsys dlvision-10g hardware 1.20
In hardware revision 1.20 one more fan controller is added to dlvision-10g.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30 15:01:11 +02:00
Dirk Eibach
b19bf8344f powerpc/ppc4xx: Adapt gdsys 405ep boards to platform changes
Print fpga info at last_stage_init on gdsys 405ep boards.
Use dtt_init() to startup fans.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30 15:01:03 +02:00
Dirk Eibach
6e9e6c36a6 powerpc/ppc4xx: Make gdsys 405ep boards reset more generic
In order to add boards that have different hardware for fpga reset,
any 405ep gdsys board now provides these functions:

void gd405ep_init(void);
void gd405ep_set_fpga_reset(unsigned state);
void gd405ep_setup_hw(void);
int gd405ep_get_fpga_done(unsigned fpga);

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30 15:00:56 +02:00
Dirk Eibach
00251261e2 powerpc/ppc4xx: Adjust environment size on neo
Environment size on neo has to be 0x20000 for compatibilty reasons.

Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2012-04-30 15:00:49 +02:00
Wolfgang Denk
e654fac2e6 Merge branch 'marex@denx.de' of git://git.denx.de/u-boot-staging
* 'marex@denx.de' of git://git.denx.de/u-boot-staging:
  CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logic
  CMD: Fix CONFIG_CMD_SAVEBP_WRITE_SIZE -> CONFIG_CMD_SPL_WRITE_SIZE
  CMD: Fix typo CMD_FSL -> CMD_MFSL in readme
  HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUM
  CMD: Remove CMD_LOG, it's unused
  CMD: Fix typo KGBD -> KGDB on debris board
  CMD: Drop CONFIG_CMD_EMMC, it's not used
  CMD: Drop CONFIG_CMD_DFL, it's not used
  CMD: Drop CMD_DCR, it's not used
  CMD: Drop CMD_CAN, it's not used
  CMD: Remove CMD_AUTOSCRIPT, it's not used
  AT91: Drop AT91_SPIMUX command from cmd_all
2012-04-29 14:12:10 +02:00
Jerry Huang
befb7d9f3c PowerPC: correct the SATA for p1/p2 rdb-pc platform
For p1/p2 rdb-pc platform, use the PCIe-SATA Silicon Image SATA controller.
Therefore, the SATA driver will use sata_sil, instead sata_sil3114.

Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
2012-04-24 23:58:34 -05:00
Liu Gang
5056c8e068 powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.

Master needs to:
	1. Set outbound SRIO windows in order to configure slave's registers
	   for the core's releasing.
	2. Check the SRIO port status when release slave core, if no errors,
	   will implement the process of the slave core's releasing.
Slave needs to:
	1. Set all the cores in holdoff by RCW.
	2. Be powered on before master's boot.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:33 -05:00
Liu Gang
0a85a9e705 powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
When boot from SRIO, slave's ENV can be stored in master's memory space,
then slave can fetch the ENV through SRIO interface.

NOTE: Because the slave can not erase, write master's NOR flash by SRIO
	  interface, so it can not modify the ENV parameters stored in
	  master's NOR flash using "saveenv" or other commands.

Master needs to:
	1. Put the slave's ENV into it's own memory space.
	2. Set an inbound SRIO window covered slave's ENV stored in master's
	   memory space.
Slave needs to:
	1. Set a specific TLB entry in order to fetch ucode and ENV from master.
	2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:33 -05:00
Liu Gang
3f1af81b80 powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
When boot from SRIO, slave's ucode can be stored in master's memory space,
then slave can fetch the ucode image through SRIO interface. For the
corenet platform, ucode is for Fman.

Master needs to:
	1. Put the slave's ucode image into it's own memory space.
	2. Set an inbound SRIO window covered slave's ucode stored in master's
	   memory space.
Slave needs to:
	1. Set a specific TLB entry in order to fetch ucode from master.
	2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:33 -05:00
Liu Gang
292dc6c501 powerpc/corenet_ds: Slave module for boot from SRIO
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.

The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:

master:
	1. NOR flash for its own u-boot image, ucode and ENV space.
	2. Slave's u-boot image in master NOR flash.
	3. Normally boot from local NOR flash.
	4. Configure SRIO switch system if needed.
slave:
	1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
	2. Boot location should be set to SRIO1 or SRIO2 by RCW.
	3. RCW should configure the SerDes, SRIO interfaces correctly.
	4. Slave must be powered on after master's boot.
	5. Must define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE because of no ucode
	   locally.

For the slave module, need to finish these processes:
	1. Set the boot location to SRIO1 or SRIO2 by RCW.
    2. Set a specific TLB entry for the boot process.
	3. Set a LAW entry with the TargetID SRIO1 or SRIO2 for the boot.
	4. Slave's u-boot image should be generated specifically by
	   make xxxx_SRIOBOOT_SLAVE_config.
	   This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:33 -05:00
Liu Gang
5ffa88eca7 powerpc/corenet_ds: Master module for boot from SRIO
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.

The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:

master:
	1. NOR flash for its own u-boot image, ucode and ENV space.
	2. Slave's u-boot image in master NOR flash.
	3. Normally boot from local NOR flash.
	4. Configure SRIO switch system if needed.
slave:
	1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
	2. Boot location should be set to SRIO1 or SRIO2 by RCW.
	3. RCW should configure the SerDes, SRIO interfaces correctly.
	4. Slave must be powered on after master's boot.

For the master module, need to finish these processes:
	1. Initialize the SRIO port and address space.
	2. Set inbound SRIO windows covered slave's u-boot image stored in
	   master's NOR flash.
	3. Master's u-boot image should be generated specifically by
	   make xxxx_SRIOBOOT_MASTER_config
	4. Master must boot first, and then slave can be powered on.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:32 -05:00
Liu Gang
fd0451e4ba powerpc/corenet_ds: Correct the compilation errors about ENV
When defined CONFIG_ENV_IS_NOWHERE, there will be some
compilation errors:

./common/env_nowhere.o: In function `env_relocate_spec':
./common/env_nowhere.c:38: multiple definition of `env_relocate_spec'
./common/env_flash.o: ./common/env_flash.c:326: first defined here
./common/env_nowhere.o: In function `env_get_char_spec':
./common/env_nowhere.c:42: multiple definition of `env_get_char_spec'
./common/env_flash.o:./common/env_flash.c:78: first defined here
./common/env_nowhere.o: In function `env_init':
./common/env_nowhere.c:51: multiple definition of `env_init'
./common/env_flash.o:./common/env_flash.c:237: first defined here
make[1]: *** [./common/libcommon.o] Error 1
make[1]: Leaving directory `./common'
make: *** [./common/libcommon.o] Error 2

Remove the CONFIG_ENV_IS_IN_FLASH if defined CONFIG_ENV_IS_NOWHERE.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
2012-04-24 23:58:32 -05:00
Shaohui Xie
15c8c6c20c powerpc/p2041rdb: add env in NAND support
Add env in NAND support when boot from NAND.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:31 -05:00
Shaohui Xie
c9b2feafaa powerpc/p2041rdb: add NAND and NAND boot support
New P2041RDB board will add a NAND chip, so add support for NAND and
NAND boot.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:31 -05:00
York Sun
1ba62f1017 powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
P1010RDB and p1_pc_rdb_pc has incorrect configuration for
CONFIG_DDR_RAW_TIMING. It should be CONFIG_SYS_DDR_RAW_TIMING.
Incorrect setting causes DDR failure in case of SPD absent.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-04-24 23:58:30 -05:00
Vipin KUMAR
031ed2fa74 i2c: Add support for designware i2c controller
Earlier, a driver exists in the u-boot source for designware i2c interface. That
driver was specific to spear platforms. This patch implements the i2c controller
as a generic driver which can be used by multiple platforms

The driver files are now renamed to designware_i2c.c and designware_i2c.h and
these are moved into drivers/i2c folder for reusability by other
platforms

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
2012-04-24 09:56:37 +02:00
Macpaul Lin
b9725ae3f3 board/adp-ag102: add configuration of adp-ag102
board:
Add config file of board adp-ag102
Add adp-ag102 into boards.cfg
Add adp-ag102 into MAINTAINERS

doc:
add README of ag102

Signed-off-by: Macpaul Lin <macpaul@andestech.com>
2012-04-22 16:58:23 +08:00
Jens Scharsig
0d62032e5b eb_cpux9k2: add USB host support to board
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2012-04-21 17:13:06 +02:00
Marek Vasut
02b233ecb1 CMD: CONFIG_CMD_SETECPR -> CONFIG_CMD_SETEXPR on omap3_logic
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19 22:01:14 +02:00
Marek Vasut
ae291b7315 HWW1U1A: Fix CMD_SHA1 -> CMD_SHA1SUM
Fix typo

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyle.D.Moffett@boeing.com
Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19 22:01:13 +02:00
Marek Vasut
a2026d2993 CMD: Remove CMD_LOG, it's unused
$ git grep CMD_LOG
include/configs/kilauea.h:#define CONFIG_CMD_LOG
include/configs/lwmon5.h:#define CONFIG_CMD_LOG
include/configs/makalu.h:#define CONFIG_CMD_LOG
include/configs/quad100hd.h:#undef CONFIG_CMD_LOG
include/configs/zeus.h:#define CONFIG_CMD_LOG

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19 22:01:13 +02:00
Marek Vasut
d060b00eff CMD: Fix typo KGBD -> KGDB on debris board
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: dogoil@etinsys.com
Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19 22:01:13 +02:00
Marek Vasut
e407612bbe CMD: Drop CONFIG_CMD_EMMC, it's not used
$ git grep CMD_EMMC
include/configs/u8500_href.h:#define CONFIG_CMD_EMMC

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: dirk.behme@googlemail.com
Cc: helmut.raiger@hale.at
Cc: john.rigby@linaro.org
Cc: vapier@gentoo.org
2012-04-19 22:01:13 +02:00
Marek Vasut
d5f6a15a39 CMD: Drop CONFIG_CMD_DFL, it's not used
$ git grep CMD_DFL
board/atc/ti113x.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
board/atc/ti113x.c:     pci_writew (s, PCI_COMMAND, CMD_DFLT);
board/cpc45/pd67290.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
board/cpc45/pd67290.c:  pci_writew (s, PCI_COMMAND, CMD_DFLT);
drivers/pcmcia/i82365.c:#define CMD_DFLT (PCI_COMMAND_IO|PCI_COMMAND_MEMORY| \
drivers/pcmcia/i82365.c:        pci_writew (s, PCI_COMMAND, CMD_DFLT);
include/configs/MBX.h:#define CONFIG_CMD_DFL
include/configs/MigoR.h:#define CONFIG_CMD_DFL
include/configs/digsy_mtc.h:#define CONFIG_CMD_DFL
include/configs/ms7722se.h:#define CONFIG_CMD_DFL
include/configs/ms7750se.h:#define CONFIG_CMD_DFL
include/configs/r2dplus.h:#define CONFIG_CMD_DFL
include/configs/sh7757lcr.h:#define CONFIG_CMD_DFL
include/configs/sh7785lcr.h:#define CONFIG_CMD_DFL

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pfister_Werner@intercontrol.de
Cc: iwamatsu@nigauri.org
Cc: nobuhiro.iwamatsu.yj@renesas.com
Cc: vapier@gentoo.org
Cc: wd@denx.de
Cc: yoshihiro.shimoda.uh@renesas.com
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-04-19 22:01:13 +02:00
Marek Vasut
7be5de4f46 CMD: Drop CMD_DCR, it's not used
$ git grep CMD_DCR
include/configs/ep8260.h:#undef CONFIG_CMD_DCR

Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19 22:01:12 +02:00
Marek Vasut
7d592a120a CMD: Drop CMD_CAN, it's not used
$ git grep CMD_CAN
include/configs/jadecpu.h:#define CONFIG_CMD_CAN

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Matthias Weisser <weisserm@arcor.de>
2012-04-19 22:01:12 +02:00
Marek Vasut
e7075bb753 CMD: Remove CMD_AUTOSCRIPT, it's not used
$ git grep AUTOSCRIPT
include/configs/at91sam9m10g45ek.h:#undef CONFIG_CMD_AUTOSCRIPT
include/configs/gplugd.h:#define CONFIG_CMD_AUTOSCRIPT

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
2012-04-19 22:01:12 +02:00
Nobuhiro Iwamatsu
77fe6e773a sh: ecovec: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
When calling board_late_init, we need to define CONFIG_BOARD_LATE_INIT.
The latest ecovec config defines BOARD_LATE_INIT, board_late_init is not called.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2012-04-18 11:16:46 +09:00
Wolfgang Denk
f5cdc11775 Prepare v2012.04-rc2; minor Coding Style cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2012-04-16 23:13:51 +02:00
Wolfgang Denk
db39f24151 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  ARM926EJS: Fix cache.c to comply with checkpatch.pl
  ARM926EJS: Make asm routines volatile in cache ops
  MX35: mx35pdk: wrong board revision
  ARM1136: MX35: Make asm routines volatile in cache ops
  ARM: add u-boot.imx as target for i.MX SOCs
  M28: Pull out CONFIG_APBH_DMA so it's always enabled
  DMA: Split the APBH DMA init into block and channel init
  imx: Return gpio_set_value in gpio_direction_output
  imx: Use GPIO_TO_PORT macro in the gpio driver instead of (gpio >> 5)
  imx: Add GPIO_TO_PORT macro in the mxc_gpio driver
  imx: Remove unneeded/repititive definitions from imx headers
  i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC
  MX31: mx31pdk: drop enable_caches from board file
  i.MX28: Fix initial stack pointer position
  mx35: mx35pdk: fix when cache functions are linked
  mx35: flea3: fix when cache functions are linked
  ARM: 926ejs: use debug() for misaligned addresses
  ARM1136: add cache flush and invalidate operations
  mx6qsabrelite: Fix the serial console port
  mx6qsabrelite: Add boot switch setting information into the README
  i.MX6: mx6qsabrelite: add cache commands if cache is enabled
  i.MX6: implement enable_caches()
  i.MX6: define CACHELINE_SIZE
  MX53: DDR: Fix ZQHWCTRL field TZQ_CS
  mx28evk: Add a README file
  mx28: Split the README into a common part and a m28 specific part
  tricorder: Load kernel from ubifs
  tricorder: Add UBIFS
  cm-t35: fix Ethernet reset timing
  hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORT
  BeagleBoard: Remove userbutton command and use gpio command instead
  OMAP: Move omap1510inn to Unmaintained / Orphaned
2012-04-16 23:01:12 +02:00
Stefano Babic
2f002eceae MX35: mx35pdk: wrong board revision
The board revision is detected accessing to the pmic,
that is not available before relocation (I2C).
This generates the following error:

CPU:   Freescale i.MX35 rev 2.0 at 532 MHz.
Reset cause: WDOG
<reg num> = 7 is invalid. Should be less than 0
Board: MX35 PDK 1.0

The revision number is wrong, as a default value is printed
(tested on a mx35pdk Rev. 2.0).

Move the output in the board_late_init(), when
pmic can be accessed.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-04-16 14:53:59 +02:00
Marek Vasut
e87ca8c049 M28: Pull out CONFIG_APBH_DMA so it's always enabled
The ABPH DMA is now used also by the SD card. Therefore it has to be enabled
even if NAND is disabled.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
2012-04-16 14:53:59 +02:00
Marek Vasut
9ed5dfa852 i.MX28: Fix initial stack pointer position
The patch:

  m28evk: Use GENERATED_GBL_DATA_SIZE
  commit 1084606c97

introduced usage of GENERATED_GBL_DATA_SIZE and calculation of initial stack
pointer position defived from that. Due to a small typo, the SP position moved
to 0x21f80, which is past the SRAM area. This didn't manifest on the real
hardware as the SRAM repeats there (address bits in the CPU being ignored).

Though this was caught in QEMU, where it crashed the emulator.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-04-16 14:53:59 +02:00
Stefano Babic
0792a36efb mx35: mx35pdk: fix when cache functions are linked
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-04-16 14:53:59 +02:00
Stefano Babic
81b1c9ebe1 mx35: flea3: fix when cache functions are linked
Signed-off-by: Stefano Babic <sbabic@denx.de>
2012-04-16 14:53:59 +02:00
Fabio Estevam
f4ac6cb6af mx6qsabrelite: Fix the serial console port
On mx6qsabrelite the console is ttymxc1.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-04-16 14:53:58 +02:00
Eric Nelson
66b4170b29 i.MX6: mx6qsabrelite: add cache commands if cache is enabled
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-04-16 14:53:58 +02:00
Eric Nelson
4d422fe2dc i.MX6: implement enable_caches()
disabled by default until drivers are fixed

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
2012-04-16 14:53:58 +02:00
Bernhard Walle
008ec95054 tricorder: Load kernel from ubifs
Signed-off-by: Bernhard Walle <walle@corscience.de>
2012-04-16 14:47:58 +02:00
Bernhard Walle
36f3aab2dd tricorder: Add UBIFS
Since kernel should be in a ubifs partition, we need UBIFS.
The greater malloc size is needed for UBIFS.

Signed-off-by: Bernhard Walle <walle@corscience.de>

Squashed two commits (UBIFS enabled and malloc size increased) into one.
Signed-off-by: Thomas Weber <weber@corscience.de>
2012-04-16 14:47:58 +02:00
Tom Rini
385488dc1b hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORT
With older toolchains we need CONFIG_SPL_LIBGENERIC_SUPPORT in order for
CONFIG_SPL_NAND_SUPPORT to link.

Signed-off-by: Tom Rini <trini@ti.com>
2012-04-16 14:47:58 +02:00
Joel Fernandes
aae58b954b BeagleBoard: Remove userbutton command and use gpio command instead
Remove userbutton command and do the detection in board config file using the gpio command

Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
2012-04-16 14:47:58 +02:00
Fabio Estevam
35897c86b9 configs: EB+MCF-EV123.h: Fix typo on CONFIG_SYS_HUSH_PARSER
Fix typo on CONFIG_SYS_HUSH_PARSER and also add  CONFIG_SYS_PROMPT_HUSH_PS2
to avoid build error.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-04-10 23:18:58 +02:00
Wolfgang Denk
3f0675d1a5 Merge branch 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging
* 'marek.vasut@gmail.com' of git://git.denx.de/u-boot-staging:
  LMB: Fix undefined lmb_reserve() on non-lmb platforms
  MIPS: fix endianess handling
  MIPS: fix inconsistency in config option for cache operation mode
  MIPS: board.c: fix init of flash data in bd_info
2012-04-09 21:34:27 +02:00
Wolfgang Denk
2c734cd932 Merge branch 'master' of git://git.denx.de/u-boot-net
* 'master' of git://git.denx.de/u-boot-net:
  net/designware: Change timeout loop implementation
  net/designware: Set ANAR to 0x1e1
  net/designware: Program phy registers when auto-negotiation is ON
  net/designware: Try configuring phy on each dw_eth_init
  net/designware: Consecutive writes must have delay
  net/designware: Phy address fix
  net/designware: Fix the max frame length size
  net/designware: Fix to restore hw mac address
  microblaze: Wire up LL_TEMAC driver initialization
  microblaze: Add faked LL_TEMAC driver configuration
  microblaze: Enable several ethernet driver compilation
  net: ll_temac: Add LL TEMAC driver to u-boot
  Update net subsystem maintainer in doc/git-mailrc
  net/eth.c: fix eth_write_hwaddr() to use dev->enetaddr as fall back
  mvgbe: remove warning for unused methods
2012-04-09 17:10:01 +02:00