Enable DM_SPI for am355x igep003x board.
Build is fine, but not tested.
Cc: Javier Martínez Canillas <javier@dowhile0.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Add two- and three-argument versions of CONFIG_IS_ENABLED in
linux/kconfig.h
- Adds a new feature which supports copying modified parts of
the frame buffer to the uncached hardware buffer
- Enable the copy framebuffer on various x86 targets
Create a non-cacheable mapping for the 0x600000000 physical memory region,
where MMIO registers for the PCIe XHCI controller are instantiated by the
PCIe bridge.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Remove the overlap between DRAM and device's IO area.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Some PCI Express register offsets are currently defined in multiple
drivers, move them to a common header to avoid re-definitions and
as a pre-requisite for adding new PCIe driver.
While at it replace some spaces with tabs.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
There might be hardware configurations where 64-bit data accesses
to XHCI registers are not supported properly. This patch removes
the readq/writeq so always two 32-bit accesses are used to read/write
64-bit XHCI registers, similarly as it is done in Linux kernel.
This patch fixes operation of the XHCI controller on RPI4 Broadcom
BCM2711 SoC based board, where the VL805 USB XHCI controller is
connected to the PCIe Root Complex, which is attached to the system
through the SCB bridge.
Even though the architecture is 64-bit the PCIe BAR is 32-bit and likely
the 64-bit wide register accesses initiated by the CPU are not properly
translated to a sequence of 32-bit PCIe accesses.
xhci_readq(), for example, always returns same value in upper and lower
32-bits, e.g. 0xabcd1234abcd1234 instead of 0x00000000abcd1234.
Cc: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
In current code there is no cache flush after initializing the scratchpad
buffer array with the scratchpad buffer pointers. This leads to a failure
of the "slot enable" command on the rpi4 board (Broadcom STB PCIe
controller + VL805 USB hub) - the very first TRB transfer on the command
ring fails and there is a timeout while waiting for the command completion
event. After adding the missing cache flush everything seems to be working
as expected.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
i2c changes for v2020.10
- Add support for I2C controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
- Add I2C controller support for Cortina Access CAxxxx SoCs
- new rtc methods, rtc command, and tests
- imx_lpi2c: Improve the codes to use private data
- stm32f7_i2c.c: Add new compatible "st,stm32mp15-i2c"
- stm32f7_i2c.c: Add Fast Mode Plus support
- pwm: Add PWM driver for SiFive SoC
Since the mdio code got upstreamed it is not possible
to activate network ports on CP110 Master and Slave.
The problem is in mvpp2_base_probe which is called for each
CP110 and it initializes the buffer area for descs and rx_buffers.
This should only happen once though and the bd space is actually
set to 0 after the first run of the function.
This leads to an error when the second CP110 tries the initialization
again and disables all network ports on this CP110.
This patch adds a static variable to check if the buffer area is
initialized only once globally.
Signed-off-by: Sven Auhagen <sven.auhagen@voleatech.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch enables DM_ETH for the following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch enables DM_USB and USB_STORAGE for the following
Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch switches the SATA driver from mvsata_ide to sata_mv for the
following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch converts the following Kirkwood-based LaCie boards to DM,
DM_SPI and DM_SPI_FLASH:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The spi0 alias is needed by the environment code to retrieve the SPI
flash. This patch adds some -u-boot.dtsi files, providing the spi0
aliases, for all the following Kirkwood-based LaCie boards:
- d2 Network v2
- Internet Space v2
- 2Big Network v2
- Network Space v2
- Network Space Lite v2
- Network Space Max v2
- Network Space Mini v2
Note that this -u-boot.dtsi files will be removed as soon as the spi0
aliases will be available in the upstream Linux dtsi files.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The helios4 is built on the same microsom as the clearfog, by syncing the config
we enable the same featureset that exists in the som on the helios4. The current
config does not boot as some of the clearfog changes needed to be made on the
helios4 also, generally speaking most changes for the clearfog should also be
made on the helios4.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Reviewed-by: Stefan Roese <sr@denx.de>
When running USB compliance tests on our Armada-385 hardware platforms
we have seen some eye mask violations. Marvell's internal documentation
says: Based on silicon test results, it is recommended to change the
impedance calibration threshold setting to 0x6 prior to calibration.
Port changes from Marvell's u-boot fork[1] to address this.
[1] - https://github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/a6221551
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Measurements on actual hardware shown that the read ODT is early by 3
clocks. Adjust the calculation to avoid this.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[upstream https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/22]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
In the Armada 385 functional spec (MV-S109094-00 Rev. C) the read sample
delay fields are 5 bits wide. Use the correct bitmask of 0x1f when
extracting the value.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
[upstream https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell/pull/22]
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present the SPL loader is not included in the TPL image so SPL cannot
be loaded. Fix it by including this file for both SPL and TPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: c87f9ce227 ("x86: Don't build some unused objects in TPL")
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These prevent use of compile-time checks such as:
if (CONFIG_IS_ENABLED(DM_SPI))
since, for example, if CONFIG_SPL_DM_SPI is not enabled then the
definitions are not included by spi.h and the C code will not build.
The #ifdefs are unnecessary since there are no conflicts with the pre-DM
code. In any case we have almost switched over to driver model for SPI.
Drop these #ifdefs from spi.h to fix a build warning on chromebook_coral
in the following patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This adds a bunch of preprocessor magic to extend the capabilities of
CONFIG_IS_ENABLED. The existing semantics of
CONFIG_IS_ENABLED(FOO)
expanding to a 1 or 0 (depending on build context and the defined-ness
or not of the appropriate CONFIG_FOO/CONFIG_SPL_FOO/CONFIG_TPL_FOO)
are of course preserved. With this, one is also allowed a two-argument
form
CONFIG_IS_ENABLED(FOO, (something))
which expands to something precisely when CONFIG_IS_ENABLED(FOO) would
expand to 1, and expands to nothing otherwise. It is, in other words,
completely equivalent to the three lines
#if CONFIG_IS_ENABLED(FOO)
something
#endif
The second argument must be parenthesized in order to allow any
tokens, including a trailing comma, to appear - one use case for this
is precisely to make it a bit more ergonomic to build an array and
only include certain items depending on .config. That should increase
both readability and not least "git grep"ability.
A third variant is also introduced,
CONFIG_IS_ENABLED(FOO, (xxx), (yyy))
which corresponds to
#if CONFIG_IS_ENABLED(FOO)
xxx
#else
yyy
#endif
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot does not have loadable modules, and nothing currently uses any
of the (CONFIG_)?IS_(BUILTIN|MODULE) macros - only
the (CONFIG_)?IS_ENABLED variants are ever used.
While I understand the desire to keep this somewhat synchronized with
linux, we've already departed by the introduction of the
CONFIG_IS_ENABLED extra logic, and deleting these makes the next patch
much simpler, since I won't have to duplicate a lot of logic for no
real gain (as there are no users).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of using the arg1_or_junk trick to pick between two choices,
with a bit of duplication between the branches (and most of the
CONFIG_TPL_BUILD case being redundant, as _IS_TPL is known to be
defined to 1 in that case), simply define a prefix that we inject
between CONFIG_ and the given config symbol.
This only requires one level of indirection (to get the
_CONFIG_PREFIX macro expanded before the token concatenation takes
place), and makes it easy to, say, introduce a CONFIG_HOSTTOOL_
prefix. [I would expect most HOSTTOOL_ symbols to just be def_bool y,
but it would allow us to clean up some of the ifdef HOSTCC mess in the
sources shared between U-Boot and host tools.]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add parentheses around CONFIG_IS_ENABLED() in the if statement, to
fix potential build failures.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This seems like a more reasonable resolution for this board, since it is
quite slow. It also allows it to work with a 5" LCD display in my lab.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the video driver to support this feature and enable it on
minnowmax to speed up the display.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from over 13 seconds to
300ms, at 1280x1024.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the video driver to support this feature and enable it on link.
Also remove the multi-line scrolling since normal scrolling is fast enough
now.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from about 930ms to 29ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the video driver to support this feature and enable it on samus.
Also remove the multi-line scrolling since normal scrolling is fast enough
now.
With this change, the time taken to print the environment to the display
without CONFIG_CONSOLE_SCROLL_LINES is reduced from about 430ms to 12ms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For PCI video devices that are not mentioned in the devicetree, U-Boot
does not bind a driver before relocation, since PCI is not fully probed
at that point. Furthermore it is possible for the video device to be on
a secondary bus which is not even scanned.
This is fine if the framebuffer is allocated in fixed memory, as it
normally is on x86. But when using this as a copy framebuffer, we also
need U-Boot to allocate its own cached framebuffer for working in. Since
the video driver is never bound before relocation, the framebuffer size
is never set and U-Boot does no allocation.
Add a new CONFIG option to reserve 16MB of memory for this eventuality.
This allows vesa devices to use the copy framebuffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present video_bottom is set to the bottom of each framebuffer when it
is allocated. This is not correct, since it should hold the bottom of the
entire area available for framebuffers.
Fix this by adding a private address in the uclass which keeps track of
the next available spot for a framebuffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
When the copy framebuffer is in use, we must also have the standard U-Boot
framebuffer available. Update the FSP driver to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
When using a copy framebuffer we need to tell the video subsystem its
address. U-Boot's normally allocated framebuffer is used as the working
buffer, but nothing is displayed until it is copied to the copy
framebuffer.
For this to work the video driver must request that a framebuffer be
allocated separately from the hardware framebuffer, so add a check for
that.
Also add a log category so that logging appears correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Enable this feature on sandbox by updating the SDL driver to have two
framebuffers.
Update the video tests to check that the copy framebuffer is kept in sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This struct is not commented but needs it. Also fix the comment in
check_vidconsole_output() about the encoding for the rotation value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Adjust the bitmap code to sync to the copy framebuffer when done.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the implementation to keep a track of what it changes in the frame
buffer and then tell the copy buffer about it. Use the special
vidconsole_memmove() helper so that memmove() operations are also
reflected in the copy buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the implementation to keep a track of what it changes in the frame
buffer and then tell the copy buffer about it. Use the special
vidconsole_memmove() helper so that memmove() operations are also
reflected in the copy buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update the implementation to keep a track of what it changes in the frame
buffer and then tell the copy buffer about it. Use the special
vidconsole_memmove() helper so that memmove() operations are also
reflected in the copy buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add a convenience function to call video_sync_copy() for a vidconsole.
Also add a memmove() helper, which does the memmove() as well as the sync.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Update video_clear() to also sync to the copy framebuffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This framebuffer is separately mapped. Update the video post-probe
function to set this up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Some architectures use a cached framebuffer and flush the cache as needed
so that changes are visible. This is supported by U-Boot.
However x86 uses an uncached framebuffer with a 'write-combining' feature
to speed up writes. Reads are permitted but they are extremely expensive.
Unfortunately, reading from the frame buffer is quite common, e.g. to
scroll it. This makes scrolling very slow.
Add a new feature which supports copying modified parts of the frame
buffer to the uncached hardware buffer. This speeds up scrolling by at
least 10x on x86 so the extra complexity cost seems worth it.
As a starting point, add the Kconfig, update the video structures to keep
track of the buffer and add a function to do the copy.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add a few notes to explain the purpose of each member of this struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
All of the functions in this file only apply if DM_VIDEO is enabled. Drop
the #ifdef as it just clutters things up. Add the needed forward
declaration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present when the console is rotated 180 degrees it starts almost a
whole character to the left of the right edge (typically 7 pixels with
an 8-pixel-wide font). On a display which aligns with the font width,
this just wastes space. On a display that does not this can result in
x_frac going negative for the final character (the one on the left
side) and the overflow -EAGAIN check at the start of the function
failing.
Change the function to start at the rightmost pixel to fix these
problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The functions in this file do similar things but not always in the same
way. To make the code easier to read and compare, use a separate 'linenum'
variable in every function. This is then multiplied by the line length to
get the offset within the frame buffer to modify. Also use an 'x' variable
to hold the pixel position within that line. This is multipled by the
pixel size and added to the offset.
Also move the pbytes declaration up a little with the other long lines.
A side effect of splitting out these variables is that they are promoted
to int, i.e. a signed type, from the unsigned short used in the
vidconsole_priv struct. This would be necessary should any of the
variables go negative. At present this can actually happen in
console_putc_xy_2(), if the display width is not a multiple of the
character size (see next patch).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add a devicetree property to select a rotated console. This uses the same
encoding as vidconsole itself: 0=normal; 1=90 degrees clockwise, 2=upside
down, 3=90 degrees anticlockwise.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
