add a weak dummy function g_dnl_fixup to add the possibility to update
the device_desc board specific. Used on the upcoming siemens board
support, where idVendor and idProduct is stored in an eeprom.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
- set in to_dfu_mode() f_dfu->dfu_state = DFU_STATE_dfuIDLE
as after every to_dfu_mode call this is done, so move
this into to_dfu_mode
- switch in dfu_bind() into dfu mode:
This fixes wrong "dfu-util -l" output, when calling
"dfu-util -l" after a board reset, without doing a
download before. See also discussion here:
http://lists.denx.de/pipermail/u-boot/2013-June/157272.html
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
This patch memcpy is used instead of an assignment to
avoid unaligned access execption on some ARM platforms.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This patch use get|put_unaligned_le16 to access structure data
to avoid data abort on some ARM platforms.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Marek Vasut <marex@denx.de>
Dfu transfer uses a buffer before writing data to the
raw storage device. Make the size (in bytes) of this buffer
configurable through environment variable "dfu_bufsiz".
Defaut value is configurable through CONFIG_SYS_DFU_DATA_BUF_SIZE
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Tom Rini <trini@ti.com>
Patch 35fc84fa1 [Refactor the bootm command to reduce code duplication]
breaks booting Linux (compressed uImage with fdt) on powerpc.
boot_jump_linux() mustn't be called before boot_prep_linux() and
boot_body_linux() have been called. So remove the superfluous call
to boot_jump_linux() in arch/powerpc/lib/bootm.c as its called later on
in this function.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@ti.com>
At present mkimage is set up to always build with image signing support.
This means that the SSL libraries (e.g. libssl-dev) are always required.
Adjust things so that mkimage can be built with and without image signing,
controlled by the presence of CONFIG_FIT_SIGNATURE in the board config file.
If CONFIG_FIT_SIGNATURE is not enabled, then mkimage will report a warning
that signing is not supported. If the option is enabled, but libraries are
not available, then a build error similar to this will be shown:
lib/rsa/rsa-sign.c:26:25: fatal error: openssl/rsa.h: No such file or directory
Signed-off-by: Simon Glass <sjg@chromium.org>
This restores the ordering of interrupt disable to what it what before
commit 35fc84fa. It seems that on some archiectures (e.g. PowerPC) the
OS is loaded into an interrupt region, which can cause problems if
interrupts are still running.
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
With 35fc84fa1 [Refactor the bootm command to reduce code duplication]
we stopped checking the return value of bootm_load_os (unintentionally!)
and simply returned if we had a non-zero return value from the function.
This broke the valid case of a legacy image file of a single kernel
loaded into an overlapping memory area (the default way of booting
nearly all TI platforms).
The best way to fix this problem in the new code is to make
bootm_load_os be the one to see if we have a problem with this, and if
it's fatal return BOOTM_ERR_RESET and if it's not BOOTM_ERR_OVERLAP, so
that we can avoid calling lmb_reserve() but continue with booting. We
however still need to handle the other BOOTM_ERR values so re-work
do_bootm_states so that we have an error handler at the bottom we can
goto for problems from bootm_load_os, or problems from the other callers
(as the code was before). Add a comment to do_bootm_states noting the
existing restriction on negative return values.
Signed-off-by: Tom Rini <trini@ti.com>
---
Changes in v2:
- Rework so that only bootm_load_os and boot_selected_os head down into
the err case code, and other errors simply return back to the caller.
Fixes 'spl export'.
We've been dropping SoC name from U-Boot prompt as it increase
complexity for automatic testing and makes line longer for no good
reason.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Andy Voltz <andy.voltz@timesys.com>
This adds a default environment which should be able to support both
3.0.15 from Timesys and upcoming 3.11.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Andy Voltz <andy.voltz@timesys.com>
Currently we have the following on boot:
CPU: Freescale i.MX28 rev1.2 at 454 MHz
BOOT: SSP SD/MMC #0, 3V3
DRAM: 128 MiB
MMC: MXS MMC: 0
Video: MXSFB: 'videomode' variable not set!In: serial
Break the line of the warning message in order to have a better reading format.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
enum boot_mode is defined twice once in spl.h and also in
spl_boot.c, hence removing the same from spl_boot.c and including
the header file.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In a714321 we add a check at the end of findfdt to make sure we have
updated it from undefined and if not, warn the user. This however
forgot a ';' on the end of the previous last test.
Signed-off-by: Tom Rini <trini@ti.com>
SDRAMC_DARCn_BA() macro worked fine when the BA is 0x00000000 even
though the macro is incorrect. It causes the BA to be set incorrctly
for other base addresses. This patch fixes the macro so that base
addresses other than zero can be used with the MCF5235.
Signed-off-by: Steve deRosier <derosier@gmail.com>
There is a debug call in board.c befor serial interface was initialized.
This moves the debug code behind serial_initialize call.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Newer gcc versions warn about unused variables. This patch corrects a few of
those warnings that popped up in a build for the palmtreo680 board.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Create a README.mxs file that contains instructions on how to use U-boot for
both MX23 and MX28.
As boot from NAND has only been tested on mx28, make it clear that it only
applies to MX28.
While at it, do some small cleanups for the sake of consistency:
- Use "MX28" instead of "i.MX28"
- Use "section" instead of "chapter" when referring to specific parts of the
reference manual chapters.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
MX28 can boot from SSP0 or SSP1, so it is better not to hardcode the SSP port
in the instructions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
In order to improve readability keep the text within 80 columns.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The SabreSD platform is available with i.MX6Q or i.MX6DL. This patch adds the
support of the i.MX6DL. The config file and the board directory are renamed
to remove the reference to the MX6Q.
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Align the list of default commands mentioned in the configuration options
paragraph of the README with the actual definitions found in
include/config_cmd_default.h
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
With CONFIG_SYS_64BIT_LBA, lbaint_t gets defined as a 64-bit type,
which is required to represent block numbers for storage devices that
exceed 2TiB (the block size usually is 512B), e.g. recent hard drives.
For some obscure reason, the current U-Boot code uses lbaint_t for the
number of blocks to read (a rather optimistic estimation of how RAM
sizes will evolve), but not for the starting address. Trying to access
blocks beyond the 2TiB boundary will simply wrap around and read a
block within the 0..2TiB range.
We now use lbaint_t for block start addresses, too. This required
changes to all block drivers as the signature of block_read(),
block_write() and block_erase() in block_dev_desc_t changed.
Signed-off-by: Sascha Silbe <t-uboot@infra-silbe.de>
This patch introduces support for command line arguments to Plan 9.
Plan 9 generally dedicates a small region of kernel memory (known
as CONFADDR) for runtime configuration. A new environment variable
named confaddr was introduced to indicate this location when copying
arguments.
Signed-off-by: Steven Stallion <sstallion@gmail.com>
[trini: Adapt for Simon's changes about correcting argc, no need to bump
by 2 now]
Signed-off-by: Tom Rini <trini@ti.com>
The spi clock divisor is of the form x * (2**y), or x << y, where x is
1 to 16, and y is 0 to 15. Note the similarity with floating point numbers.
Convert the desired divisor to the smallest number which is >= desired divisor,
and can be represented in this form. The previous algorithm chose a divisor
which could be almost twice as large as needed.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Fix two issues with the calculation of pre_div and post_div:
1. pre_div: While the calculation of pre_div looks correct, to set the
CONREG[15-12] bits pre_div needs to be decremented by 1:
The i.MX 6Dual/6Quad Applications Processor Reference Manual (IMX6DQRM
Rev. 0, 11/2012) states:
CONREG[15-12]: PRE_DIVIDER
0000 Divide by 1
0001 Divide by 2
0010 Divide by 3
...
1101 Divide by 14
1110 Divide by 15
1111 Divide by 16
I.e. if we want to divide by 2, we have to write 1 to CONREG[15-12].
2. In case the post divider becomes necessary, pre_div will be divided by
16. So set pre_div to 16, too. And not 15.
Both issues above are tested using the following examples:
clk_src = 60000000 (60MHz, default i.MX6 ECSPI clock)
a) max_hz == 23000000 (23MHz, max i.MX6 ECSPI read clock)
-> pre_div = 3 (divide by 3 => CONREG[15-12] == 2)
-> post_div = 0 (divide by 1 => CONREG[11- 8] == 0)
=> 60MHz / 3 = 20MHz SPI clock
b) max_hz == 2000000 (2MHz)
-> pre_div = 16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 1 (divide by 2 => CONREG[11- 8] == 1)
=> 60MHz / 32 = 1.875MHz SPI clock
c) max_hz == 1000000 (1MHz)
-> pre_div = 16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 2 (divide by 4 => CONREG[11- 8] == 2)
=> 60MHz / 64 = 937.5kHz SPI clock
d) max_hz == 500000 (500kHz)
-> pre_div = 16 (divide by 16 => CONREG[15-12] == 15)
-> post_div = 3 (divide by 8 => CONREG[11- 8] == 3)
=> 60MHz / 128 = 468.75kHz SPI clock
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Add a description of how to implement verified boot using signed FIT images,
and a simple test which verifies operation on sandbox.
The test signs a FIT image and verifies it, then signs a FIT configuration
and verifies it. Then it corrupts the signature to check that this is
detected.
Signed-off-by: Simon Glass <sjg@chromium.org>
