This patch changes nand_wait_ready() to not just call nand_wait(),
since this will send a new command to the NAND chip. We just want to
wait for the chip to become ready here.
Signed-off-by: Stefan Roese <sr@denx.de>
- Fixing leading white spaces
- Fixing indentation where 4 spaces are used instead of tab
- Removing C++ comments (//), wherever I introduced them
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
When building the 8544DS board we get this error:
In file included from r8a66597-hcd.c:22:
u-boot/include/usb.h:190:2: error: #error USB Lowlevel not defined
make[1]: *** [r8a66597-hcd.o] Error 1
The cleanest fix is to only build r8a66597-hcd.c if CONFIG_USB_R8A66597_HCD
is set.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The block and page parameters of onenand_verify_page() are not used. This causes a compiler error when CONFIG_MTD_ONENAND_VERIFY_WRITE is enabled.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
FILL_15BIT_555RGB macro extension for pixel swapping
by commit bed53753dd
introduced a bug in cfb_console:
Bitmaps with odd-numbered width won't be rendered
correctly and even U-Boot crashes are observed on
some platforms while repeated rendering of such
bitmaps with "bmp display". Also if a bitmap is
rendered to an odd-numbered x starting position,
the same problem occurs. This patch is an attempt
to fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
If logo_plot() should ever be called with x starting
position other than zero and for pixel depths greater
than 8bpp, logo colors distortion will be observed.
This patch fixes the issue.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The CFI driver allowed only for static initializers in the
CFG_FLASH_BANKS_LIST definition, i. e. it did not allow to map
several flash banks contiguously if the bank sizes were not known in
advance, which kind of violates U-Boot's design philosophy.
(will be used for example by the TQM8xxL boards)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add MII commands to the UEC driver. Note that once a UEC device is selected,
any device on its MDIO bus can be addressed.
Signed-off-by: David Saada <david.saada@ecitele.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
add support for Renesas R8A66597 usb controller.
This patch supports USB Host mode.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Add support to drivers/usb/usbdcore_omap1510.c for OMAP5912 and OMAP16xx devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
The Atmel lcd controller is used on Atmel's AT91 (little endian) and
AVR32 (big endian) platforms.
As such, the controller can handle both big and little endian memory.
This patch fixes the driver for the AVR32 platform.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
The current implementation of get_timer() is only really useful after we
have relocated u-boot to memory. The i2c code is used before that as part
of the SPD DDR setup.
We actually have a bug when using the get_timer() code before relocation
because the .bss hasn't been setup and thus we could be reading/writing
a random location (probably in flash).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prevent i2c_init() in fsl_i2c.c from writing to the data segment before
relocation. Commit d8c82db4 added the ability for i2c_init() to program the
I2C bus speed and save the value in i2c_bus_speed[], which is a global
variable. It is an error to write to the data segment before relocation,
which is what i2c_init() does when it stores the bus speed in i2c_bus_speed[].
Signed-off-by: Timur Tabi <timur@freescale.com>
This got broken by commits 93c56f212c
[cfi_flash: support of long cmd in U-boot.]
That command needs to be in little endian format on BE machines
with CFG_WRITE_SWAPPED_DATA. Without this patch, the command 0xf0
gets saved on stack as 0x00 00 00 f0 and 0x00 gets written into
the cmdbuf in case portwidth = chipwidth = 8bit.
Cc: Alexey Korolev <akorolev@infradead.org>
Cc: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Round the serial port clock divisor value returned by
calc_divisor()
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
This got changed by commit 93c56f212c
[cfi_flash: support of long cmd in U-boot.]
Long is the wrong type because it will behave differently on 64bit
machines in a way that is probably not expected. u32 should be
enough.
Cc: Alexey Korolev <akorolev@infradead.org>
Cc: Vasiliy Leonenko <vasiliy.leonenko@mail.ru>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Add function of new PCI, pci_skip_dev and pci_print_dev.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We need to wait while drawing engine clears frame
buffer before any further software accesses to frame
buffer will be initiated. Otherwise software drawn
parts could be partially destroyed by the drawing
engine or even GDC chip freeze could occur (as
observed on socrates board).
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Clean Makefile
Move device specific values to driver for better reading
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stefan Roese <sr@denx.de>
Redesign uartlite driver to in_be32 and out_be32 macros
Fix missing header in io.h
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The formula "counter = (u32) (gd->bus_clk / gd->baudrate) / 32"
can generate the wrong divisor due to integer division truncation.
Round the calculated divisor value by adding 1/2 the baudrate
before dividing by the baudrate.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Some boards based on AT91SAM926X-EK use smaller DF chips to keep
bootstrap, u-boot and its environment, using NAND or other external
storage for kernel and rootfs. This patch adds support for
small 1024x263 chip.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
