Commit graph

265 commits

Author SHA1 Message Date
Mike Frysinger
2cc8b5c0e8 net: rtl8109: drop unused !NET_MULTI driver
No one uses this driver, and it isn't converted to the NET_MULTI
framework (which we dropped recently), so drop this driver too.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-11-22 08:39:25 +01:00
Wolfgang Denk
87a5d60103 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  ARM: Add Calxeda Highbank platform
  dkb: make mmc command as default enabled
  Marvell: dkb: add mmc support
  ARM: pantheon: add mmc definition
  davinci: remove config.mk file from the sources
  ARM:AM33XX: Add support for TI AM335X EVM
  ARM:AM33XX: Added timer support
  ARM:AM33XX: Add emif/ddr support
  ARM:AM33XX: Add clock definitions
  ARM:AM33XX: Added support for AM33xx
  omap3/emif4: fix registers definition
  davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
  davinci: emac: add support for more than 1 PHYs
  davinci: emac: add new features to autonegotiate for EMAC
  da850evm: Move LPSC configuration to board_early_init_f()
  omap4_panda: Build in cmd_gpio support on panda
  omap: Don't use gpio_free to change direction to input
  mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
  OMAP3: overo : Add environment variable optargs to bootargs
  OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
  OMAP3: overo : Use ttyO2 instead of ttyS2.
  da830: add support for NAND boot mode
  dm36x: revert cache disable patch
  dm644X: revert cache disable patch
  devkit8000: Add malloc space
  omap: spl: fix build break due to changes in FAT
  OMAP3 SPL: Provide weak omap_rev_string
  omap: beagle: Use ubifs instead of jffs2 for nand boot
  omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
  omap: overo: Configure mux for gpio10
  SPL: Add DMA library
  omap3: Add interface for omap3 DMA
  omap3: Add DMA register accessors
  omap3: Add Base register for DMA
  arm, davinci: add missing LSPC define for MMC/SD1
  U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
  DaVinci: correct MDSTAT.STATE mask
  omap4: splitting padconfs into common, 4430 and 4460
  omap4: adding revision detection for 4460 ES1.1
  omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
  gplug: fixed build error as a result of code cleanup patch
  kirkwood_spi: add dummy spi_init()
  gpio: mvmfp: reduce include platform file
  ARM: orion5x: reduce dependence of including platform file
  serial: reduce include platform file for marvell chip
  ARM: kirkwood: reduce dependence of including platform file
  ARM: armada100: reduce dependence of including platform file
  ARM: pantheon: reduce dependence of including platform file
  Armada100: Add env storage support for Marvell gplugD
  Armada100: Add SPI flash support for Marvell gplugD
  Armada100: Add SPI support for Marvell gplugD
  SPI: Add SPI driver support for Marvell Armada100
  dreamplug: initial board support.
  imx: fix coding style
  misc: pmic: drop old Freescale's pmic driver
  MX31: mx31pdk: use new pmic driver
  MX31: mx31ads: use new pmic driver
  MX31: mx31_litekit: use new pmic driver
  MX5: mx53evk: use new pmic driver
  MX5: mx51evk: use new pmic driver
  MX35: mx35pdk: use new pmic driver
  misc: pmic: addI2C  support to pmic_fsl driver
  misc: pmic: use I2C_SET_BUS in pmic I2C
  MX5: efikamx/efikasb: use new pmic driver
  MX3: qong: use new pmic driver
  RTC: Switch mc13783 to generic pmic code
  MX5: vision2: use new pmic driver
  misc: pmic: Freescale PMIC switches to generic PMIC driver
  misc:pmic:samsung Enable PMIC driver at GONI target
  misc:pmic:max8998 MAX8998 support at a new PMIC driver.
  misc:pmic:core New generic PMIC driver
  mx31pdk: Remove unneeded config
  mx31: provide readable WEIM CS accessor
  MX51: vision2: Set global macros
  I2C: Add i2c_get/set_speed() to mxc_i2c.c
  ARM: Update mach-types
  devkit8000: Add config to enable SPL MMC boot
  devkit8000: protect board_mmc_init
  arm, post: add missing post_time_ms for arm
  cosmetic, post: Codingstyle cleanup
  arm, logbuffer: make it compileclean
  tegra2: Enable MMC for Seaboard
  tegra2: Add more pinmux functions
  tegra2: Rename PIN_ to PINGRP_
  tegra2: Add more clock functions
  tegra2: Clean up board code a little
  tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
2011-10-28 00:15:19 +02:00
Helmut Raiger
9660e442de cosmetic: s/BOARD_LATE_INIT/CONFIG_BOARD_LATE_INIT
This renames BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT.
Along the way it removes some leftover

 #define BOARD_LATE_INIT		1

and adds some basic documentation for board specific
callbacks in README.

Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
2011-10-27 23:53:59 +02:00
Heiko Schocher
ee4014b005 arm, logbuffer: make it compileclean
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-10-27 21:56:30 +02:00
Simon Glass
eea63e05d0 fdt: ARM: Add fdtcontroladdr to set device tree address in environment
This adds support for a new environment variable called 'fdtcontroladdr'. If
defined, the hex address is used as the address of the control fdt for U-Boot.

Note: I have not changed CONFIG_PRAM section as I already have an
outstanding patch on that.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-26 21:40:16 +02:00
Simon Glass
f5437ad141 fdt: ARM: Implement and verify embedded and separate device tree
This locates the device tree either embedded within U-Boot or attached to the
end as a separate binary.

When CONFIG_OF_CONTROL is defined, U-Boot requires a valid fdt. A check is
provided for this early in initialisation.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-26 21:39:57 +02:00
Simon Glass
bc4e14c43c arm: Correct build error introduced by getenv_ulong() patch
Commit dc8bbea removed a local variable that is used in most ARM boards.

Since we want to avoid an 'unused variable' warning with later compilers,
and the #ifdef logic of whether this variable is required is bit painful,
this declares the variable local to the block of code that needs it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-24 21:13:51 +02:00
Simon Glass
dc8bbea017 arm: Use getenv_ulong() in place of getenv(), strtoul
This changes the board code to use the new getenv_ulong() function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2011-10-23 23:33:17 +02:00
Wolfgang Denk
80c6abc306 arch/arm/lib/board.c: fix warning: variable ... set but not used
Fix:
board.c:445:8: warning: variable 'bd' set but not used [-Wunused-but-set-variable]

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-10-09 23:24:48 +02:00
Mike Frysinger
e2a53458a7 net: drop !NET_MULTI code
This is long over due.  All but two net drivers have been converted, but
those have now been dropped.

The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined.  So here we scrub the
core code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:22:16 +02:00
Valentin Longchamp
ea3681a6e4 POST/arm: adaptations needed for POST on ARM to work
For post to run on ARM, 3 things are needed:
- post_log_word to be defined in gd
- a post.h include in arch/arm/lib/board.c

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05 22:03:10 +02:00
Jason Kridner
2d3be7c456 led: remove camel casing of led identifiers globally
Result of running the following command to address Wolfgang's
comment about camel case:

for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done

Discussion:
http://patchwork.ozlabs.org/patch/84988/

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-13 08:30:52 +02:00
Aneesh V
cabe2878a8 armv7: cache: remove flush on un-aligned invalidate
Remove the flush of boundary cache-lines done as part
of invalidate on a non cache-line boundary aligned
buffer

Also, print a warning when this situation is recognized.

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-09-04 11:36:16 +02:00
Aneesh V
cba4b1809f arm: do not force d-cache enable on all boards
c2dd0d4554 added dcache_enable()
to board_init_r(). This enables d-cache for all ARM boards.
As a result some of the arm boards that are not cache-ready
are broken. Revert this change and allow platform code to
take the decision on d-cache enabling.

Also add some documentation for cache usage in ARM.

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-09-04 11:36:16 +02:00
Igor Grinberg
15c2e2c0ea arm: fix bd pointer dereference prior initialization
gd->bd pointer has been used prior been initialized.
Move the relevant code after the initialization.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2011-09-03 22:40:46 +02:00
Heiko Schocher
b2b8f98f88 arm, lib/board.c: use gd->ram_size instead of bd->bi_memsize
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Albert Aribaud <albert.u.boot@aribaud.net>
2011-09-03 22:40:46 +02:00
Matthias Weisser
34fe8281d7 arm: lib: memcpy: Do not copy to same address
In some cases (e.g. bootm with a elf payload which is already at the right
position) there is a in place copy of data to the same address. Catching this
saves some ms while booting.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2011-09-03 22:40:45 +02:00
Heiko Schocher
ceb1d6d75e cosmetic: arm: lib/board.c: Coding Style cleanup
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
cc: Albert Aribaud <albert.u.boot@aribaud.net>
cc: <macpaul@gmail.com>
cc: Wolfgang Denk <wd@denx.de>
2011-08-04 13:39:25 +02:00
Andreas Bießmann
09c2e90c11 unify version_string
This patch removes the architecture specific implementation of
version_string where possible. Some architectures use a special place
and therefore we provide U_BOOT_VERSION_STRING definition and a common
weak symbol version_string.

Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Peter Pan <pppeterpppan@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-07-28 17:22:53 +02:00
Aneesh V
401bb30b6d replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
replace all occurences of CONFIG_PRELOADER with CONFIG_SPL_BUILD

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-26 14:44:34 +02:00
Aneesh V
05bad4aa56 scaled down version of generic libraries for SPL
Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-26 14:44:25 +02:00
Igor Grinberg
7eb29398c0 arm: add CONFIG_MACH_TYPE setting and documentation
CONFIG_MACH_TYPE is used to set the machine type number in the
common arm code instead of setting it in the board code.
Boards with dynamically discoverable machine types can still set the
machine type number in the board code.

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
2011-07-17 11:07:01 +02:00
Aneesh V
93bc21930a armv7: add PL310 support to u-boot
PL310 is the L2$ controller from ARM used in many SoCs
including the Cortex-A9 based OMAP4430

Add support for some of the key PL310 operations
	- Invalidate all
	- Invalidate range
	- Flush(clean & invalidate) all
	- Flush range

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-04 10:55:25 +02:00
Aneesh V
e05f00792b arm: minor fixes for cache and mmu handling
1. make sure that page table setup is not done multiple times
2. flush_dcache_all() is more appropriate while disabling cache
   than a range flush on the entire memory(flush_cache())

   Provide a default implementation for flush_dcache_all()
   for backward compatibility and to avoid build issues.

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-04 10:55:25 +02:00
Aneesh V
c2dd0d4554 armv7: integrate cache maintenance support
- Enable I-cache on bootup
- Enable MMU and D-cache immediately after relocation
	- Do necessary initialization before enabling d-cache and MMU
- Changes to cleanup_before_linux()
	- Make changes according to the new framework

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-04 10:55:25 +02:00
Aneesh V
e47f2db537 armv7: rename cache related CONFIG flags
Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:

CONFIG_L2_OFF	     -> CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_NO_ICACHE -> CONFIG_SYS_ICACHE_OFF
CONFIG_SYS_NO_DCACHE -> CONFIG_SYS_DCACHE_OFF

Signed-off-by: Aneesh V <aneesh@ti.com>
V2:
 * Changed CONFIG_L2_OFF -> CONFIG_SYS_NO_L2CACHE
V4:
 * Changed all three flags to the final names suggested as above
   and accordingly changed the commit message
2011-07-04 10:55:25 +02:00
Aneesh V
4c93da7c39 arm: make default implementation of cache_flush() weakly linked
make default implementation of cache_flush() weakly linked so that
sub-architectures can override it

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-07-04 10:55:25 +02:00
Wolfgang Denk
9623c158f6 Merge branch 'master' of git://git.denx.de/u-boot-arm
* 'master' of git://git.denx.de/u-boot-arm:
  run arm_pci_init after relocation
  IXP42x PCI rewrite
  update/fix PDNB3 board
  update/fix IXDP425 / IXDPG425 boards
  add dvlhost (dLAN 200 AV Wireless G) board
  IXP NPE: add support for fixed-speed MII ports
  update/fix AcTux4 board
  update/fix AcTux3 board
  update/fix AcTux2 board
  update/fix AcTux1 board
  use -ffunction-sections / --gc-sections on IXP42x
  support CONFIG_SYS_LDSCRIPT on ARM
  fix "depend" target in npe directory
  Fix IXP code to work after relocation was added
  trigger hardware watchdog in IXP42x serial driver
  add support for IXP42x Rev. B1 and newer
  add XScale sub architecture (IXP/PXA) to maintainer list

Conflicts:
	arch/arm/lib/board.c

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-06-23 15:37:33 +02:00
Michael Schwingen
1ed63c5498 run arm_pci_init after relocation
Signed-off-by: Michael Schwingen <michael@schwingen.org>
2011-06-23 08:25:19 +02:00
Wolfgang Denk
566e5cf451 ARM: drop unsupported 'trab' board
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it.  Drop it.

This includes support for VFD displays which have always been used by
this board only.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-06-22 20:00:51 +02:00
Wolfgang Denk
cd6881b519 Minor coding style cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-05-19 22:22:44 +02:00
Wolfgang Denk
f38536f913 Merge branch 'master' of git://git.denx.de/u-boot-arm 2011-04-27 21:48:09 +02:00
Minkyu Kang
d32a1a4caa Don't grab memory for LCD if FB address is defined
If FB address is defined specific address then don't grab memory for LCD

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
2011-04-27 19:38:11 +02:00
Eric Cooper
6445a3051e ARM: fix stack pointer adjustment in board_init_f()
Since addr_sp is a byte address, it should be adjusted by 12 here.

Signed-off-by: Eric Cooper <ecc@cmu.edu>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Wolfgang Denk <wd@denx.de>
2011-04-27 19:38:09 +02:00
Matthias Weisser
d8834a1323 arm: Use optimized memcpy and memset from linux
Using optimized versions of memset and memcpy from linux brings a quite
noticeable speed (x2 or better) improvement for these two functions.

Here are some numbers for test done with jadecpu

                           | HEAD(1)| HEAD(1)| HEAD(2)| HEAD(2)|
                           |        | +patch |        | +patch |
---------------------------+--------+--------+--------+--------+
Reset to prompt            |  438ms |  330ms |  228ms |  120ms |
                           |        |        |        |        |
TFTP a 3MB img             | 4782ms | 3428ms | 3245ms | 2820ms |
                           |        |        |        |        |
FATLOAD USB a 3MB img*     | 8515ms | 8510ms | ------ | ------ |
                           |        |        |        |        |
BOOTM LZO img in RAM       | 3473ms | 3168ms |  592ms |  592ms |
 where CRC is              |  615ms |  615ms |   54ms |   54ms |
 uncompress                | 2460ms | 2462ms |  450ms |  451ms |
 final boot_elf            |  376ms |   68ms |   65ms |   65ms |
                           |        |        |        |        |
BOOTM LZO img in FLASH     | 3207ms | 2902ms | 1050ms | 1050ms |
 where CRC is              |  600ms |  600ms |  135ms |  135ms |
 uncompress                | 2209ms | 2211ms |  828ms |  828ms |
                           |        |        |        |        |
Copy 1.4MB from NOR to RAM |  134ms |   72ms |  120ms |   70ms |

(1) No dcache
(2) dcache enabled in board_init
*Does not work when dcache is on

Size impact:

C version:
   text    data     bss     dec     hex filename
 202862   18912  266456  488230   77326 u-boot

ASM version:
   text    data     bss     dec     hex filename
 203798   18912  266288  488998   77626 u-boot
222712  u-boot.bin

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
2011-04-27 19:38:07 +02:00
Grant Likely
55b0a39314 Respect memreserve regions specified in the device tree
If a regions is reserved in the fdt, then it should not be used.  Add
the memreserve regions to the lmb so that u-boot doesn't use them to
store the initrd.

Signed-off-by: Grant Likely <grant.likely@linaro.org>
2011-04-25 21:11:21 -04:00
Grant Likely
590d3cacb9 Stop passing around bootmem_base value.
For the calls to boot_relocate_fdt(), boot_get_cmdline(), and
boot_get_kbd(), the value of bootmem_base is always obtained by
calling getenv_bootm_low().  Since the value always comes from the
same source, the calling signature for those functions can be
simplified by making them call getenv_bootm_low() directly.

Signed-off-by: Grant Likely <grant.likely@linaro.org>
2011-04-25 21:11:19 -04:00
Po-Yu Chuang
f326cbba98 arm: fix incorrect monitor protection region in FLASH
Monitor protection region in FLASH did not cover .rel.dyn
and .dynsym sections, because it uses __bss_start to compute
monitor_flash_len. Use _end instead.

Add _end to linker scripts for end of u-boot image
Add _end_ofs to all the start.S.

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-03-27 19:18:52 +02:00
Po-Yu Chuang
3a8a83e08d arm: get_sp() should always be compiled
get_sp() was incorrectly excluded if none of
  CONFIG_SETUP_MEMORY_TAGS
  CONFIG_CMDLINE_TAG
  CONFIG_INITRD_TAG
  CONFIG_SERIAL_TAG
  CONFIG_REVISION_TAG
were defined.

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-02-21 08:30:55 +01:00
Peter Tyser
eddf52b593 Replace "FLASH" strings with "Flash" or "flash"
There's no compelling reason to have the output on bootup or the
"flinfo" command print "flash" in uppercase, so use the proper case
where appropriate.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2011-01-19 00:02:37 +01:00
Heiko Schocher
296cae732b arm: add 8-byte alignment for ABI compliance before board_init_f
suggested from Daniel Hobi<daniel.hobi@schmid-telecom.ch>

Tested on following boards:
arm1136: qong
armv7: omap3_beagle
arm926ejs: magnesium, tx25

Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
cc: Albert ARIBAUD <albert.aribaud@free.fr>
2010-12-08 23:50:09 +01:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Steve Sakoman
8345fb242c ARMV7: Fix build for non-OMAP3 boards
Commit c3d3a54 uses CONFIG_ARMV7 to determine whether to call the
v7_flush_cache_all function.  This breaks the build for all non-OMAP3
boards (like Panda and OMAP4430SDP) since there is only a v7_flush_cache_all
implementation for OMAP3.

This patch uses CONFIG_OMAP3XXX instead of CONFIG_ARMV7 so that only boards
with a v7_flush_cache_all will make the call.

Tested on Beagle, Overo, Panda, and OMAP4430SDP

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-04 15:27:02 -04:00
Wolfgang Denk
a9aa392629 Drop support for CONFIG_SYS_ARM_WITHOUT_RELOC
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support.  However, other recent changes led to a different
implementation (ELF relocation), where this no longer works.  By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.

So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:39:59 +02:00
Wolfgang Denk
2e5167ccad Replace CONFIG_RELOC_FIXUP_WORKS by CONFIG_NEEDS_MANUAL_RELOC
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-29 21:32:07 +02:00
Heiko Schocher
1336cad298 arm, bootm: Fix compile warning
Fix warning:

bootm.c: In function 'bootm_linux_fdt':
bootm.c:181: warning: unused variable 's'
bootm.c:180: warning: unused variable 'bd'

Signed-off-by: Heiko Schocher <hs@denx.de>
2010-10-26 21:15:35 +02:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
Enric Balletbo i Serra
cdb1d4f97e ARM: fix relocation support for onenand device.
We also have to relocate the onenand command table manually, otherwise
onenand command don't work.

Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2010-10-23 22:55:47 +02:00
Wolfgang Denk
6d8d4ef994 Merge branch 'elf_reloc'
Conflicts:
	arch/arm/include/asm/config.h
	board/LaCie/edminiv2/config.mk
	board/karo/tx25/config.mk
	board/logicpd/imx27lite/config.mk
	doc/README.arm-relocation

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-19 21:07:52 +02:00
John Rigby
2d1916e48b ARM: add flat device tree support
Based on other architectures already supported.
Tested on OMAP3 Beagle board and another unnamed ARM platform.

Signed-off-by: John Rigby <john.rigby@linaro.org>
Tested-by: Rob Herring <rob.herring@smooth-stone.com>
Acked-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:54:00 +02:00
Steve Sakoman
d470a6f60a env_mmc: Fix crashing bug encountered after enabling ARM relocation
The crash was occuring in env_relocate because it was being called prior
to mmc_initialize.  This patch moves the MMC initialization earlier in
the init process.

This patch also cleans up the env_relocate_spec code in env_mmc.c

Signed-off-by: Steve Sakoman <steve.sakoman@linaro.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2010-10-13 21:52:13 +02:00
Heiko Schocher
c3d3a5418d armv7, beagle: add support for ELF relocations
Signed-off-by: Heiko Schocher <hs@denx.de>
2010-10-13 10:12:25 +02:00
Albert Aribaud
92d5ecba47 arm: implement ELF relocations
ELF relocation tables generated with linker option -pie can
be used to fixup code and data in a single loop at relocation,
removing the need for manual fixups anywhere else in the code.

Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
2010-10-13 10:10:21 +02:00
Ben Gardiner
7b37a27e14 davinci_emac: davinci_eth_set_mac_addr to ->write_hwaddr
This patch proposes to migrate the davinci_emac driver to using the
eth_device->write_hwaddr function pointer as suggested by Ben Warren.

All the davinci boards had the behaviour, prior to this patch, of
sync'ing the environment variable enetaddr with the MAC address read
from non-volatile storage on boot -- when the two locations disagreed,
the environment variable value took precendence. This patch keeps the
same behaviour but lets eth_initialize take care of it.

This patch refactors davinci_emac setup in the boards so that the MAC
address is read from non-volatile storage into the environment variable
and then the environment variable value is use in eth_intialize. The
only exception is the direct call to davinci_eth_set_mac_addr made by
the da830evm board init which was changed into an assignment of the
enetaddr field.

Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Nick Thompson <nick.thompson@ge.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-10-11 23:07:17 -07:00
Heiko Schocher
f1d2b313c9 ARM: add relocation support
!! This breaks support for all arm boards !!

To compile in old style, you must define
CONFIG_SYS_ARM_WITHOUT_RELOC or you can compile
with "CONFIG_SYS_ARM_WITHOUT_RELOC=1 ./MAKEALL board"

!! This define will be removed soon, so convert your
board to use relocation support

Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Heiko Schocher <hs@denx.de>

Fix boot from NAND for non-ARM systems
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-19 19:29:53 +02:00
Heiko Schocher
7e4a9e6dc8 ARM (ARM11): add data cache support, test on Qong board
Add data cache support for arm1136 systems.

Enable "cache" command on Qong board and test performance.

    Test 1: Loading 127 MB of data from NAND flash into RAM:

    Instr. Cache	off	on	on
      Data Cache	off	off	on
    --------------------------------------------------
    QONG (ARM11)	177s	95s	43s	= x 4.1

    Test 2: uncompressing a gzipped image from RAM to RAM
            (size compressed: 6.5 MiB, uncompressed: 35 MiB):

    Instr. Cache	off	on	on
      Data Cache	off	off	on
    --------------------------------------------------
    QONG (ARM11)	1.54s	0.95s	0.18s	= x 8.6

Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Heiko Schocher <hs@denx.de>
2010-09-19 19:29:51 +02:00
Heiko Schocher
95c6f6d34d ARM V7 (OMAP): add data cache support, test on Beagle board
Add data cache support for ARM V7 systems. Used cache flush
functions from linux:arch/arm/mm/cache-v7.S developed from
Catalin Marinas.

Enable "cache" command on Beagle board and test performance.

    Test 1: Loading 127 MB of data from NAND flash into RAM:

    Instr. Cache	off	on	on
      Data Cache	off	off	on
    --------------------------------------------------
    Beagle (Cortex A8)	116s	106s	30.3s	= x 3.8

    Test 2: uncompressing a gzipped image from RAM to RAM
            (size compressed: 6.5 MiB, uncompressed: 35 MiB):

    Instr. Cache	off	on	on
      Data Cache	off	off	on
    --------------------------------------------------
    Beagle (Cortex A8)	1.84s	1.64s	0.12s	= x 15.3

Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Ben Gardiner<bengardiner@nanometrics.ca>
2010-09-19 19:29:51 +02:00
Heiko Schocher
c3330e9d6a ARM (ARM926ejs): add data cache support, tested on magnesium and tx25 board
Enable "cache" command on tx25 and magnesium board and test performance.

    Test 1: Loading 127 MB of data from NAND flash into RAM:

    Instr. Cache        off     on      on
      Data Cache        off     off     on
    --------------------------------------------------
    magnesium           32,6s   22,5s   30s     = x 1,09
    tx25 (29MB only)    9,69s   5,05s   8,16s   = x 1,19

    Test 2: uncompressing a gzipped image from RAM to RAM
            (size compressed: 6.5 MiB, uncompressed: 35 MiB):

    Instr. Cache        off     on      on
      Data Cache        off     off     on
    --------------------------------------------------
    magnesium           4,25s   2,08s   1,72s   = x 2,47
    tx25                4,82s   2,04s   1,84s   = x 2,62

Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Alessandro Rubini <rubini@gnudd.com>
2010-09-19 19:29:51 +02:00
Heiko Schocher
880eff5cfb ARM: cp15: setup mmu and enable dcache
This has been tested on at91sam9263 and STN8815.
Again, I didn't check if it has bad effects
on non-arm926 cores.

Initially I had a "done" bit to only set up page tables
at the beginning. However, since the aligmnent requirement
was for the whole object file, this extra integer tool 16kB
in BSS, so I chose to remove it.

Also, note not all boards use PHYS_SDRAM, but it looks like
it's the most used name (more than CONFIG_SYS_DRAM_BASE for
example).

Portions of this work were supported by funding from
the CE Linux Forum.

Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
2010-09-19 19:29:50 +02:00
Terry Lv
a80603598c Save environment data to mmc.
This patch is to save environment data to mmc card.
It uses interfaces defined in generic mmc.

Signed-off-by: Terry Lv <r65388@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2010-09-19 17:47:29 +02:00
Wolfgang Denk
cdb749778a Rename getenv_r() into getenv_f()
While running from flash, i. e. before relocation, we have only a
limited C runtime environment without writable data segment. In this
phase, some configurations (for example with environment in EEPROM)
must not use the normal getenv(), but a special function.  This
function had been called getenv_r(), with the idea that the "_r"
suffix would mean the same as in the _r_eentrant versions of some of
the C library functions (for example getdate vs. getdate_r, getgrent
vs. getgrent_r, etc.).

Unfortunately this was a misleading name, as in U-Boot the "_r"
generally means "running from RAM", i. e. _after_ relocation.

To avoid confusion, rename into getenv_f() [as "running from flash"]

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
2010-08-04 00:45:36 +02:00
Wolfgang Denk
54841ab50c Make sure that argv[] argument pointers are not modified.
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands.  Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".

This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:

int main (int argc, char **argv)
{
	while (--argc > 0 && **++argv == '-') {
/* ====> */	while (*++*argv) {
			switch (**argv) {
			case 'd':
				debug++;
				break;
			...
			default:
				usage ();
			}
		}
	}
	...
}

The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell.  With the modification, the compiler will prevent this with
an
	error: increment of read-only location '*argv'

N.B.: The code above can be trivially rewritten like this:

	while (--argc > 0 && **++argv == '-') {
		char *arg = *argv;
		while (*++arg) {
			switch (*arg) {
			...

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2010-07-04 23:55:42 +02:00
Minkyu Kang
47ea6edfb3 ARM: remove unused VIDEOLFB ATAG
ATAG_VIDEOLFB is not used anywhere.
The belowing warning is occurred due to this ATAG.

[    0.000000] Ignoring unrecognised tag 0x54410008

This patch fixed it.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Martin Krause <Martin.Krause@tqs.de>
2010-06-23 00:11:10 +02:00
Wolfgang Denk
cd4b02be1b ARM: add __aeabi_unwind_cpp_pr0() function to avoid linker complaints
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Thomas Weber <weber@corscience.de>
2010-05-15 19:50:36 +02:00
Peter Tyser
ea0364f1bb Move lib_$ARCH directories to arch/$ARCH/lib
Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk

This change is intended to clean up the top-level directory structure
and more closely mimic Linux's directory organization.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:03 +02:00