This converts the following to Kconfig:
CONFIG_SPL_BOARD_INIT
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
The IICDVFS(I2C) set in r8a7796.h is common in rcar-gen3.
This moves CONFIG_SYS_I2C_SH_BASE0 in rcar-gen3-base.h.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Salvator-X can have both H3 and M3 CPU on it, drop the
select R8A7795 to allow both configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A7796 r1.1 reports itself as r2.0 , add quirk into the
PRR code to fix this report.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add entry for the R8A7796 RCar M3 SoC into the CPU info table.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add entry for the R8A7795 RCar H3 SoC into the CPU info table.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This Kconfig option is not used on any board, so drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the R8A7796 PFC and GPIO tables from the latest 3.5.3 release
from Renesas .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Sync the PFC and GPIO tables with the latest 3.5.3 release from
Renesas . This adds ES2.0 support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SDIO is not supported in u-boot, there is no point in enabling mmc3.
For this purpose, add u-boot specific dtsi that this will be included
automatically while building the dtb.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update Kconfig and Makefile to enable Arria 10.
Clean up Makefile and sorting *.o alphanumerically.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add system manager register struct and macros for Arria 10.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Restructure misc driver in the preparation to support A10.
Move the Gen5 specific code to gen5 file.
Change all uint32_t_to u32.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Restructure system manager in the preparation to support A10.
No functional change.
Change uint32_t to u32.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Restructure reset manager driver in the preparation to support A10.
Move the Gen5 specific code to gen5 files.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Restructure clock manager driver in the preparation to support A10.
Move the Gen5 specific code to _gen5 files.
- Change all uint32_t to u32 and change to use macro BIT(n) for bit shift.
- Check return value from wait_for_bit(). So change return type to int for
cm_write_with_phase() and cm_basic_init().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Sync with Linux commit 308ac756("Merge tag 'gpio-v4.11-3'").
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
SPL FIT is able to pick the suitable fdt file for u-boot,
so add that function through board_fit_config_name_match.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Drop the unneeded code. lib/time.c use timebase_l/h.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This patch updates the mksunxiboot tool to optionally add
the default device tree name string to the SPL header. This
information can be used by the firmware upgrade tools to
protect users from harming themselves by trying to upgrade
to an incompatible bootloader.
The primary use case here is a non-removable bootable media
(such as NAND, eMMC or SPI flash), which already may have
a properly working, but a little bit outdated bootloader
installed. For example, the user may download or build a
new U-Boot image for "Cubieboard", and then attemept to
install it on a "Cubieboard2" hardware by mistake as a
replacement for the already existing bootloader. If this
happens, the flash programming tool can identify this
problem and warn the user.
The size of the SPL header is also increased from 64 bytes
to 96 bytes to provide enough space for the device tree name
string.
[Andre: split patch to remove OF_LIST hash feature]
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The Allwinner SoCs with 64-bit cores use an ARM Trusted Firmware binary,
which needs to be loaded alongside U-Boot proper.
Set the respective Kconfig options to let them select this feature and
also automatically build the FIT image.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[Rename Kconfig path to arch/arm/mach-sunxi/Kconfig]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The generic ARMv8 assembly code contains routines for setting up
a CCN interconnect, though the Freescale SoCs are the only user.
Link this code only for Freescale targets, this saves some precious
bytes in the chronically tight SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Not every SoC needs to set up the GIC interrupt controller, so link
think code only when the respective config option is set.
This shaves off some bytes from the SPL code size.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When booting from ARM Trusted Firmware, U-Boot runs in EL1-NS.
The boot flow is as follows:
BL1 -> BL2 -> BL31 -> BL33 (i.e. U-Boot)
This boot sequence works fine for LD11 SoC (Cortex-A53), but LD20
SoC (Cortex-A72) hangs in U-Boot. The solution I found is to
read sctlr_el1 and write back the value as-is. This should be
no effect, but surprisingly fixes the problem for LD20 to boot.
I do not know why.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
match other TI platforms in the same situation.
Signed-off-by: Tom Rini <trini@konsulko.com>
Newer SoCs use same TV encoder unit. Split it out so it can be reused
with new DM video driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC
This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The symbol CONFIG_OMAP_VC_I2C_HS_MCODE always uses the default value.
Restructure the comment and code such that if a need arises later to use
another value we can address this then.
Signed-off-by: Tom Rini <trini@konsulko.com>
The symbols CONFIG_OMAP3_GPIO_X control if we enable the clocks for a
given GPIO bank in U-Boot. select the required banks for each target.
In some cases we need to also migrate from CONFIG_USB_EHCI (deprecated,
in include/configs/) to CONFIG_USB_EHCI_HCD as we only require the GPIO
bank to be enabled if USB is also enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
While in theory this value could be used in places outside of "omap5"
(such as OMAP4), we only make use of it today in OMAP5, so place the
Kconfig entry there. Given that Kconfig lets us provide a default, we
drop CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC entirely. The contents of
doc/README.omap-reset-time make a good help entry, so adjust them
slightly and delete the file. Move the comment about range to where we
use the value now, and have Kconfig enforce the upper bound.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the two cases in the code where we use CONFIG_OMAP as a useful test
currently we can make use of CONFIG_ARCH_OMAP2PLUS instead. With that
changed we can drop all defines of CONFIG_OMAP. While in here,
CONFIG_OMAP3430 is only defined and then never used, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
The SMPEN bit is located in the cpuectlr_el1 register and not the
cpuactlr_el1 register. Adjust the comment accordingly and also fix
a spelling error.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
CC: Mingkai Hu <mingkai.hu@nxp.com>
CC: Gong Qianyu <Qianyu.Gong@nxp.com>
CC: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
CC: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
CC: York Sun <york.sun@nxp.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.
Also drop I2C options which depend on this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Change tbu/l type to unsigned int.
>From the timer file for arm,
"(((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;" is used,
This piece code is based on tbu/tbl is 32bits, so change the type to
unsigned int.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The variable grf is only referenced if EARLY_DEBUG is defined so move the
declaration to be under the existing guard.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For early debug, the following configs needs to be enabled:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_OMAP=y
CONFIG_DEBUG_UART_BASE=0x44e09000
CONFIG_DEBUG_UART_CLOCK=48000000
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_DEBUG_UART_ANNOUNCE=y
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For early debug, the following configs needs to be enabled:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_OMAP=y
CONFIG_DEBUG_UART_CLOCK=48000000
CONFIG_DEBUG_UART_SHIFT=2
CONFIG_DEBUG_UART_ANNOUNCE=y
For DRA7xx:
CONFIG_DEBUG_UART_BASE=0x4806a000
For AM57xx:
CONFIG_DEBUG_UART_BASE=0x48020000
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update MPU frequencies and voltages as per the latest
DM[1] dated: OCT 2011 Revised APRIL 2016, Section 5.4.
Below is the consolidated data:
MPU values for PG 2.0 and later(Package ZCZ and ZCE):
-------------------------------------------------------
| | ZCZ | ZCE |
|-------------------------------------------------------|
| | VDD[V] | ARM [MHz] | VDD[V] | ARM [MHz] |
|-------|----------|------------|----------|------------|
| NITRO | 1.325 | 1000 | NA | NA |
|-------|----------|------------|----------|------------|
| TURBO | 1.26 | 800 | NA | NA |
|-------|----------|------------|----------|------------|
|OPP120 | 1.20 | 720 | NA | NA |
|-------|----------|------------|----------|------------|
|OPP100 | 1.10 | 600 | 1.10 | 600 |
|-------|----------|------------|----------|------------|
| OPP50 | 0.95 | 300 | 0.95 | 300 |
-------------------------------------------------------
There is no eFuse blown on PG1.0 Silicons due to which there is
no way to detect the maximum frequencies supported. So default
to OPP100 for which both frequency and voltages are common on both
the packages.
[1] http://www.ti.com/lit/ds/symlink/am3356.pdf
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This configuration should be valid for all F7 family devices in general.
Here is the regions info:
- Region0 : 4GB : cacheable & executable.
- Region1 : 512MB : text area : strogly ordered & executable.
- Region2 : 512MB : peripherals : device memory & non-executable.
- Region3 : 512MB : peripherals : device memory & non-executable.
- Region4 : 512MB : cortexM area: strongly ordered & non-executable.
Higher region number overrides the lower region configuration.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Cortex-M archs support option memory protection unit (MPU). MPU is used
to set the memory types, attributes, access permissions for different regions,
cache policies of the device.
e.g. using MPU it is possible to configure memory region as device memory
or strongly ordered, memory attributes like execute never, cache policies
like write-back or write-through.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Data cache memory needs to be disabled before handing over control to
linux kernel. This patch populates the cleanup_before_linux stub.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Add functionality to flush & invalidate all the dcache using the
prototype declared in common header file.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Add dummy functions for the not-enabled case]
Signed-off-by: Tom Rini <trini@konsulko.com>
am335x_evm SPL is very close to its limit in SRAM space.
Switch to use tiny printf to reclaim some size.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
No reason to use a separate load script for am33xx than using
omap-common load script.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding support for fdt fixup to update the
memory node in device tree for falcon boot.
This is needed for single stage or falcon
bootmode, to pass memory configuration to
kernel through DT memory node.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Declare the size of ddr very early in spl, so that this can be
used to enable cache.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
At present there is not operation to invalidate a cache range. This seems
to be needed to fill out the cache operations. Add an implementation based
on the flush operation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
This adds a new firefly-rk3399 board, MIPI support for rk3399 and
rk3288, rk818 pmic support, mkimage improvements for rockchip and a few
other things.
Add dts config for mipi display, include vop, mipi controller, panel, backlight
. And Enable rk808 for lcd_3v3 in another patch.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add mipi display mode for rk3399 vop, so that we can use mipi panel
for display.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add GRF register declaration for mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since this driver can be used for rk8xx series pmic,
let's rename rk808 to rk8xx, to make it clear.
Configs parts are done by sed -i "s/RK808/RK8XX/g" `grep RK808 -lr ./`
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Set ethernet mac address in late init for Tinker Board,
prevents getting a random mac address each boot.
Read mac address from eeprom, first 6 bytes from m24c08@50.
Same as /etc/init.d/rockchip.sh on Tinker OS.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Simon Glass <sjg@chromium.org>
To add HDMI support for the RK3399, this commit provides the needed
pinctrl functionality to configure the HDMI I2C pins (used for reading
the screen's EDID).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Firefly-rk3399 is a bord from T-Firefly, you can find detail about
it here:
http://en.t-firefly.com/en/firenow/Firefly_RK3399/
This patch add basic node for the board and make it able to bring
up.
Peripheral/interfaces on board:
- usb hub which connect to ehci controller;
- UART2 debug
- eMMC
- PCIe
- USB 3.0 HOST, type-C port
- sdio, sd-card
- HDMI
- Ethernet
- OPTICAL
- WiFi/BT
- MIPI CSI/DSI
- IR
- EDP/DP
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The kernel dts has update a lot since the first time we commit rk3399.dtsi,
sync with kernel for further development.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are 3 regions used by rk3399 ATF:
- bl31 code, located at 0x10000;
- cortex-m0 code and data, located at 0xff8c0000;
- bl31 data, located at 0xff8c1000 ~ 0xff8c4000;
SPL_TEXT_BASE starts from 0xff8c2000, we need to reserve memory
for ATF data, or else there will be memory corrupt after SPL
loads the ATF image.
More detail about cortex-M0 code in ATF:
https://github.com/ARM-software/arm-trusted-firmware/commit/
8382e17c4c6bffd15119dfce1ee4372e3c1a7890
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
GMAC controller need to init the tx io driver strength to 13mA,
just like the description in dts pinctrl node, or else the controller
may only work in 100MHz Mode, and fail to work at 1000MHz mode.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com>>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since our sdram driver is ready, we can use the actual size
instead of hard code.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
enable debug uart for rk3288 and print something to let people know
where we are
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pwm3 on evb-rk3399 is used for pwm regulator, need to invert
the polarity to make it work correctly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
With the validation done for DDR3-1600 (i.e. 800 MHz bus clock), we
add the timings (rk3399-sdram-ddr3-1600.dtsi) and change rk3399-puma.dts
to use these by default.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop blank line at end of file:
Signed-off-by: Simon Glass <sjg@chromium.org>
The DDR3-1333 timings for the RK3399-Q7 (Puma) has some unintended
left-over comments in them. This change cleans the file up.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds support for the pin-configuration of the SPI5
controller of the RK3399 through the following changes:
* grf_rk3399.h: adds definition for configuring the SPI5 pins
in the GPIO2C group
* periph.h: defines PERIPH_ID_SPI3 through PERIPH_ID_SPI5
* pinctrl_rk3399.c: adds the reverse-mapping from the IRQ# to
PERIPH_ID_SPI5; dispatches PERIPH_ID_SPI3
through SPI5 to the appropriate pin-config
function; implements the pin-configuration
for PERIPH_ID_SPI5 using the GPIO2C group
X-AffectedPlatforms: RK3399-Q7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
RK3399 device memory region is 0xf8000000~0xffffffff.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is needed in order to allow building it for other archs.
Move relocation comment to a better place.
Remove no longer needed dts FIXME.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
As requested, I added the CONFIG_TWL4030_POWER to Kconfig and made it
the implied default when selecting OMAP34XX as a platform.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch also removes all the excessive code for NS16550 intiailization
as the device tree can do that now. This also adds DM_I2C and DM_MMC
since the overlying drivers have the built-in support already. The
corresponding include/config/omap3_logic.h also reduced in size
due to the new device tree support.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Retain Auto-detect ability between SOM-LV and Torpedo
Split this off from the device sub submissions
Previous commit has this combined with SOM-LV. This commit has only
the Torpedo Device Tree.
The device trees were sync'd with 4.9.y stable with two changes:
disable mmc2 and stdout-path = &uart1. Both of those two changes
will be submitted to the linux-omap list
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Split device tree from other board
This adds the device tree. Previous commit added both boards at the
same time.
Signed-off-by: Adam Ford <aford173@gmail.com>
Changes in V2:
Split the SOM-LV from Torpedo
Some OMAP3 devices support an SMSC ethernet PHY connected to the GPMC bus.
This copies this device tree from Linux 4.9.y stable
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Many OMAP3 boards use a TWL4030 PMIC. This brings in the related
device tree information for common TWL4030 and TWL4030 with OMAP3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3630 boards.
DM3730 can use this same device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add device tree support to allow for CONFIG_OF_CONTROL in OMAP3 boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch changes the way DM_MMC calculates offset to the base register of
MMC. Previously this was through an #ifdef but that wasn't necessary for OMAP3.
This patch will now add in the offset to the base address based on the
.compatible flags.
Signed-off-by: Adam Ford <aford173@gmail.com>
V2: Remove ifdef completely and reference offset from the omap_hsmmc_ids table.
V1: Change ifdef to ignore OMAP3
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a function to set the video parameters to the msg handler and remove
it from the video driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add a function to get the video size to the msg handler and remove it from
the video driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
The bcm283x chips provide a way for the ARM core to communicate with the
graphics processor, which is in charge of many things. This is handled by
way of a message prototcol.
At present the code for sending message (and receiving a reply) is spread
around U-Boot, primarily in the board file. This means that sending a
message from a driver requires duplicating the code.
Create a new message implementation with a function to support powering on
a subsystem as a starting point.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is needed to probe devices under that bus such as the SATA PHY.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9263ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9rlek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9g20ek and at91sam9260ek
boards are copied from the Linux v4.10, do the changes below.
- Fix the build error for the usb0 node.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property for the dbgu node are used
in board_init_f stage.
- Add the clk pinctrl of the mmc0 node.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9m10g45ek boards are copied
from the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD, pioE) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9n12ek boards are copied from
the Linux v4.10, do the changes as below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC, pioD) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the pinctrl-names of mmc0 node.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the "u-boot,dm-pre-reloc" property to determine which nodes
which are needed by SPL and by the board_init_f stage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Move existing configuration from header file to defconfig or dts as
appropriate.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Align PHY selectors register with Armada-CP-110 functional SPEC
update all relevant device trees with this change.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
UTMI_PHY_TO_USB_HOST was used in USB3 UTMI dts node only, but there will
be USB2 UTMI dts node for some SoCs that have got USB2 controller, so rename
TO_USB_HOST to TO_USB3_HOST to distinguish TO_USB2_HOST in later on patches.
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Use correct naming as done in the latest Marvell U-Boot version as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Fix spelling error of SERDES_VERSION
- Remove superfluous definition of this macro
- Remove unnecessary include of i2c.h
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add NAND to CP master device tree. Add armada-7040-db-nand
device tree for the board configured with NAND boot device.
Add comment about boot device ID to armada-7040-db DTS.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Implement mvebu_get_nand_clock call for A8K family.
This function is used by PXA3XX NAND driver.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add PCIe initialization at early init stage.
This operation has a side effect of detecting all PCIe
plug-in cards, so the operator is not obligated to issue
"pci enum" command though CLI for this purpose.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Sync the default configuration of Armada-8040-DB with
Marvell u-boot-2015 standard configuration "A" for the same board.
The standard configuration "A" enables 2 PCIe slots on CP0
and 3 PCIe slots on CP1.
This is the main configuration used for u-boot and Linux tests.
This patch also re-arranges the DTS file entries by grouping
all nodes related to CP0 and CP1.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable by default DM_I2C for all Texas Instruments Keystone 2 based
evms.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Enable I2C0 and I2C1 which is needed to enable usage of DM I2C.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add aliases for I2C nodes required for the DM framework to probe the
davinci-i2c driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add I2C nodes to the 66AK2Gx dtsi.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
One some keystone2 platforms like K2G ICE, there is an option
to switch between 24MHz or 25MHz as sysclk. But the existing
driver assumes it is always 24MHz. Add support for getting
all reference clocks dynamically by reading boot pins.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G supports various sysclk frequencies which can be
determined using sysboot pins. PLLs should be configured
based on this sysclock frequency. Add PLL configurations
for all supported sysclk frequencies.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
ARM errata 852421 and 852423 applies to r1p0, r1p1 and r1p2
revisions of Cortex-A17 processors. These workarounds
exist in Linux kernel and I thought it would be better
to add them in to U-Boot.
Signed-off-by: Nisal Menuka <nisalmenuka23@gmail.com>
Remove unnecessary apb and ahb nodes and just override necessary
nodes/values.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refactor SCU header to use consistent Mask & Shift values.
Now, consistently, to read value from SCU register, mask needs
to be applied before shift.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for clocks needed by MACs to ast2500 clock driver.
The clocks are D2-PLL, which is used by both MACs and PCLK_MAC1 and
PCLK_MAC2 for MAC1 and MAC2 respectively.
The rate of D2-PLL is hardcoded to 250MHz -- the value used in Aspeed
SDK. It is not entirely clear from the datasheet how this clock is used
by MACs, so not clear if the rate would ever need to be different. So,
for now, hardcoding it is probably safer.
The rate of PCLK_MAC{1,2} is chosen based on MAC speed selected through
hardware strapping.
So, the network driver would only need to enable these clocks, no need
to configure the rate.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add P-Bus Clock support to ast2500 clock driver.
This is the clock used by I2C devices.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver uses Generic Pinctrl framework and is compatible with
the Linux driver for ast2500: it uses the same device tree
configuration.
Not all pins are supported by the driver at the moment, so it actually
compatible with ast2400. In general, however, there are differences that
in the future would be easier to maintain separately.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change switches all existing users of ast2500 Watchdog to Driver
Model based Watchdog driver.
To perform system reset Sysreset Driver uses first Watchdog device found
via uclass_first_device call. Since the system is going to be reset
anyway it does not make much difference which watchdog is used.
Instead of using Watchdog to reset itself, SDRAM driver now uses Reset
driver to do that.
These were the only users of the old Watchdog API, so that API is
removed.
This all is done in one change to avoid having to maintain dual API for
watchdog in between.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Reset Driver configuration to ast2500 SoC Device Tree and bindings
for various reset signals
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Reset Driver for ast2500 SoC. This driver uses Watchdog Timer to
perform resets and thus depends on it. The actual Watchdog device used
needs to be configured in Device Tree using "aspeed,wdt" property, which
must be WDT phandle, for example:
rst: reset-controller {
compatible = "aspeed,ast2500-reset";
aspeed,wdt = <&wdt1>;
}
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make functions for locking and unlocking SCU part of SCU API.
Many drivers need to modify settings in SCU and thus need to unlock it
first. This change makes it possible.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver supports ast2500 and ast2400 SoCs.
Only ast2500 supports reset_mask and thus the option of resettting
individual peripherals using WDT.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch is required for correct SPL device tree creation by fdtgrep
as fdtgrep looks for u-boot,dm-pre-reloc property of the node to include
it in the spl device tree.
Not adding it in these subnodes ignores the pin muxing of peripherals
which is almost always in the subnodes.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The IGEP SMARC AM335x is an industrial processor module with
following highlights:
o AM3352 TI processor (Up to AM3359)
o Cortex-A8 ARM CPU
o SMARC form factor module
o Up to 512 MB DDR3 SDRAM / 512 MB FLASH
o WiFi a/b/g/n and Bluetooth v4.0 on-board
o Ethernet 10/100/1000 Mbps and 10/100 Mbps controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Pau Pajuelo <ppajuelo@iseebcn.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
Rename igep0033 to igep003x as IGEP SMARC AM335x module (igep0034)
can use the same source files.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
am33xx does not support OneNAND, but we need this define anyway
to let UBI SPL code compile.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
This board support stm32f7 family device stm32f769-I with 2MB internal Flash &
512KB RAM.
STM32F769 lines offer the performance of the Cortex-M7 core (with double
precision floating point unit) running up to 216 MHz.
To compile for stm32f769 board, use same defconfig as stm32f746-disco,
the only difference is to pass "DEVICE_TREE=stm32f769-disco".
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Actually the sdram memory on stm32f746 discovery board is micron part
MT48LC_4M32_B2B5_6A. This patch does the modification required in the
device tree node & driver for the same.
Also we are passing here all the timing parameters in terms of clock
cycles, so no need to convert time(ns or ms) to cycles.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
All discovery boards have one user button & one user LED. Here we are
just reading the button status & switching ON the user LED.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.
Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Also created alias for gpios for stm32f7 discovery board. Based on these
aliases, it would be possible to get gpio devices by sequence.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
This patch also removes the sdram/fmc clock enable from board specific
code.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
At present fdt blob or argument address being passed to kernel is fixed at
compile time using macro CONFIG_SYS_SPL_ARGS_ADDR. FDT blob from
different media like nand, nor flash are copied to the address pointed
by the macro.
The problem is, it makes args/fdt blob compulsory to copy which is not required
in cases like for NOR Flash. This patch removes this limitation.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
The symbol CONFIG_DRA7XX is needed for Kconfig conditions.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
In dram_init_banksize there seems to be a typo concerning
a plausibility check of the fdt.
Testing sc > 2 twice does not make any sense.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
R40 has a similar SATA controller with the ones on A10/A20, but with a
reset line added (like other peripherals on sun6i+), and two extra VDD
pins added (1.2v and 2.5v).
Add clock configuration of R40 SATA.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
For the consistent location of SoC-level Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With 3f66149d9f we no longer have a common call fdt_fixup_ethernet.
This was fine to do on PowerPC as they largely had calls already in
ft_cpu_fixup. On ARM however we largely relied on this call. Rather
than introduce a large number of changes to ft_cpu_fixup /
ft_board_fixup we recognize that this is a common enough call that we
should be doing it in a central location. Do it early enough that we
can do any further updates in ft_cpu_fixup / ft_board_fixup.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Chou <thomas@wytron.com.tw> (maintainer:NIOS)
Cc: York Sun <york.sun@nxp.com> (maintainer:POWERPC MPC85XX)
Cc: Stefan Roese <sr@denx.de> (maintainer:POWERPC PPC4XX)
Cc: Simon Glass <sjg@chromium.org>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 3f66149d9f ("Remove extra fdt_fixup_ethernet() call")
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_DIAG
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_DIAG on some keymile configs]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_DEKBLOB
Note: This option does not seem to actually be enabled by any board.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply under SECURE_BOOT for mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than using CMD_CRAMFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CRAMFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply FS_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_CRAMFS
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_CLK
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply CMD_CLK on ARCH_ZYNQ]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_BMODE
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y and depend on mx5/6/7]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_BLOB
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add imply CMD_BLOB under CHAIN_OF_TRUST]
Signed-off-by: Tom Rini <trini@konsulko.com>
A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 /
CONFIG_MX53 being in Kconfig. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit adds support for HDMI output.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds support for DM I2C on sunxi platform. It can coexist
with old style sunxi I2C driver, because it is still used in SPL and
by some SoCs.
Because sunxi platform doesn't yet support DM clk, reset and pinctrl
driver, workaround is needed to enable clocks and set resets and
pinctrls. This is done by calling i2c_init_board() in board_init().
This means that CONFIG_I2Cx_ENABLE options needs to be correctly set
in order to use needed I2C controller.
Commit is based on the previous patch made by Philipp Tomsich
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On ARM v7M, the processor will return to ARM mode when executing
a blx instruction with bit 0 of the address == 0. Always set it
to 1 to stay in thumb mode.
Tested on STM32f746-disco board
Similar commit:
f99993c108
Author: Matt Porter <mporter@konsulko.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In Linux, CONFIG_ARCH_OMAP2PLUS is used for OMAP2 or later SoCs.
Rename CONFIG_ARCH_OMAP2 to CONFIG_ARCH_OMAP2PLUS to follow this
naming.
Move the OMAP2+ board/SoC choice down to mach-omap2/Kconfig to slim
down the arch/arm/Kconfig level.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Almost all TI defconfigs enable this already, add this as a default
and remove the explicit assignment.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are more and more cases where if we do not use gcc-6.0 or later we
run into problems where our binaries are too large for the targets.
Given the prevalence of gcc-6.0 or later toolchains at this point in
time, we give notice now that starting with v2018.01 we will require
gcc-6 (or later) for ARM.
Signed-off-by: Tom Rini <trini@konsulko.com>
The name of the gpio bank under DM_GPIO appear to be a copy-paste error.
This changes the name of the gpio bank from am33xx_gpios to omap34xx_gpios.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The register names and offset were not correct as per the TRM for OMAP3530
and OMAP3630. Correct the naing and offsets per the documentation
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fixes the following problem:
zynq-uboot> run dfu_ram
Setting bus to 1
g_dnl_register: failed!, error: -19
The cause appears to be that the USB framework is looking for a usbotg aliases,
so add the alias to point to our USB device.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the Terasic DE10-Nano board. The board
is based on the DE0-Nano-Soc board but adds a larger FPGA
and an HDMI output.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
PSCI can be used on both multiple and single core socs. Current
implementation only allows PSCI to work on multiple core socs.
This patch removes this restriction so that PSCI can work on
single core socs as well.
Signed-off-by: Chenhui Zhao <chenhui.zhao@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add Kconfig option to support loading PPA header from eMMC/SD and
NAND Flash.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we have now V3s support in board code, the V3s DTSI file should also
be added.
Add also some CCU include headers to satisfy the DTSI file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Basic U-Boot support is now present for V3s.
Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.
As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Use - instead of @ for OPP tables
- Add input-delay properties to Cadence eMMC nodes
- Restore full license text because code-diff is annoying
- Fix NAND compatible strings
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The SCP (System Control Processor) or what we call STM (Stand-by
MPU) is integrated in LD4, Pro4, sLD8, LD6b, LD11, and LD20.
For these SoCs, show the information if STM is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This configuration is supposed to be used with ARM Trusted Firmware,
so the SYSTEM_RESET is implemented in BL31. Invoke PSCI instead of
U-Boot's own reset code because we need to coordinate with SCP
(System Control Processor) for the system-level power management.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is needed for HDMI, which will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Video driver for older Allwinner SoCs uses cfb console framework which
in turn uses struct ctfb_res_modes to hold timing informations. However,
DM video framework uses different structure - struct display_timing.
It makes more sense to convert lcdc to use new timing structure because
all new drivers should use DM video framework and older drivers might be
rewritten to use new framework too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
TCON unit has similar layout and functionality also on newer SoCs. This
commit splits out TCON code for easier reuse later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.
This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40's CPU controls are a combination of sun6i and sun7i.
All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.
Last, the R40 does not have a secure SRAM block.
This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 has the CPUCFG block at the same address as the A20.
Fix it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 seems to have a variant of the memory controller found in
the H3 and A64 SoCs. Adapt the code for use on the R40. The changes
are based on released DRAM code and comparing register dumps from
boot0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the BSP released by Banana Pi, the R40 (sun8iw11p1) has
an extra "PLL lock control" register in the CCU, which controls whether
the individual PLL lock status bits in each PLL's control register work
or not.
This patch enables it for all the PLLs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The watchdog found on the R40 SoC is the older variant found on the A20.
Add the proper "#if defines" to make it work.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 SoC uses the AXP221s in I2C mode to supply power.
Some regulator's common usages have changed, and also the recommended
voltage for existing usages have changed. Update the defaults to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 is the successor to the A20. It is a hybrid of the A20, A33
and the H3.
The R40's PIO controller is compatible with the A20,
Reuse the A20 UART and I2C muxing code by adding the R40's macro.
The display pipeline is the newer DE 2.0 variant.
Block enabling video on R40 for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
At present if the return to bootrom fails (e.g. because you are not using
the Rockchip's bootrom's pointer table in MMC) then the board prints
SPL message and hangs. Print a message first if we can, to help in
understanding what happened when it hangs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Each call of va_start must be matched by a call of va_end.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
If the system is running PSCI firmware, the System Reset function
(func ID: 0x80000009) is supposed to be handled by PSCI, that is,
the SoC/board specific reset implementation should be moved to PSCI.
U-Boot should call the PSCI service according to the arm-smccc
manner.
The arm-smccc is supported on ARMv7 or later. Especially, ARMv8
generation SoCs are likely to run ARM Trusted Firmware BL31. In
this case, U-Boot is a non-secure world boot loader, so it should
not be able to reset the system directly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:
[Linux] [U-Boot]
arch/arm/kernel/smccc-call.S -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes* -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h -> include/linux/arm-smccc.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Current sysclk fixing would fix all clocks with 'fixed-clock' compatible.
This patch is to fix sysclk by path to avoid any incorrect fixing.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Number of TZASC instances may vary across NXP SoCs.
So put TZASC configuration under instance specific defines.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size
as header is appended to u-boot image. So header will also be
copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for the
header.
- Reduce the size of CAAM driver for SPL Blobification functions
and descriptors, that are not required at the time of SPL are
disabled. Further error code conversion to strings is disabled
for SPL build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add NAND secure boot target for ls1043ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
also defined.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Define bootscript and its header addresses for QSPI target
Also add PPA header address in Kconfig
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The header address of PPA defined in Kconfig.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
