Commit graph

76 commits

Author SHA1 Message Date
Anup Patel
a897269c93 cmd: Remove mmc_spi command
The mmc_spi command was added to manually setup MMC over SPI bus
using command. This was required by the legacy non-DM MMC_SPI driver.

With DM based MMC_SPI driver in-place, we can now use all general
storge commands and mmc command for MMC over SPI bus hence we remove
the mmc_spi command all it's references.

Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15 10:30:08 +08:00
Eugeniu Rosca
db7b7a05b2 cmd: Add 'bcb' command to read/modify/write BCB fields
'Bootloader Control Block' (BCB) is a well established term/acronym in
the Android namespace which refers to a location in a dedicated raw
(i.e. FS-unaware) flash (e.g. eMMC) partition, usually called "misc",
which is used as media for exchanging messages between Android userspace
(particularly recovery [1]) and an Android-capable bootloader.

On higher level, this allows implementing a subset of Android Bootloader
Requirements [2], amongst which is the Android-specific bootloader
flow [3]. Regardless how the latter is implemented in U-Boot ([3] being
the most memorable example), reading/writing/dumping the BCB fields in
the development process from inside the U-Boot is a convenient feature.
Hence, make it available to the users.

Some usage examples of the new command recorded on R-Car H3ULCB-KF
('>>>' is an overlay on top of the original console output):

=> bcb
bcb - Load/set/clear/test/dump/store Android BCB fields

Usage:
bcb load  <dev> <part>       - load  BCB from mmc <dev>:<part>
bcb set   <field> <val>      - set   BCB <field> to <val>
bcb clear [<field>]          - clear BCB <field> or all fields
bcb test  <field> <op> <val> - test  BCB <field> against <val>
bcb dump  <field>            - dump  BCB <field>
bcb store                    - store BCB back to mmc

Legend:
<dev>   - MMC device index containing the BCB partition
<part>  - MMC partition index or name containing the BCB
<field> - one of {command,status,recovery,stage,reserved}
<op>    - the binary operator used in 'bcb test':
          '=' returns true if <val> matches the string stored in <field>
          '~' returns true if <val> matches a subset of <field>'s string
<val>   - string/text provided as input to bcb {set,test}
          NOTE: any ':' character in <val> will be replaced by line feed
          during 'bcb set' and used as separator by upper layers

=> bcb dump command
Error: Please, load BCB first!
 >>> Users must specify mmc device and partition before any other call

=> bcb load 1 misc
=> bcb load 1 1
 >>> The two calls are equivalent (assuming "misc" has index 1)

=> bcb dump command
00000000: 62 6f 6f 74 6f 6e 63 65 2d 73 68 65 6c 6c 00 72    bootonce-shell.r
00000010: 79 00 72 00 00 00 00 00 00 00 00 00 00 00 00 00    y.r.............
 >>> The output is in binary/string format for convenience
 >>> The output size matches the size of inspected BCB field
 >>> (32 bytes in case of 'command')

=> bcb test command = bootonce-shell && echo true
true
=> bcb test command = bootonce-shell- && echo true
=> bcb test command = bootonce-shel && echo true
 >>> The '=' operator returns 'true' on perfect match

=> bcb test command ~ bootonce-shel && echo true
true
=> bcb test command ~ bootonce-shell && echo true
true
 >>> The '~' operator returns 'true' on substring match

=> bcb set command recovery
=> bcb dump command
00000000: 72 65 63 6f 76 65 72 79 00 73 68 65 6c 6c 00 72    recovery.shell.r
00000010: 79 00 72 00 00 00 00 00 00 00 00 00 00 00 00 00    y.r.............
 >>> The new value is NULL-terminated and stored in the BCB field

=> bcb set recovery "msg1:msg2:msg3"
=> bcb dump recovery
00000040: 6d 73 67 31 0a 6d 73 67 32 0a 6d 73 67 33 00 00    msg1.msg2.msg3..
00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................
00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00    ................
 >>> --- snip ---
 >>> Every ':' is replaced by line-feed '\n' (0xA). The latter is used
 >>> as separator between individual commands by Android userspace

=> bcb store
 >>> Flush/store the BCB structure to MMC

[1] https://android.googlesource.com/platform/bootable/recovery
[2] https://source.android.com/devices/bootloader
[3] https://patchwork.ozlabs.org/patch/746835/
    ("[U-Boot,5/6] Initial support for the Android Bootloader flow")

Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
2019-07-11 14:11:19 -04:00
Heinrich Schuchardt
005a804d0f cmd: remove unused display command
Compiling the display command leads to an error

    undefined reference to `display_set'

No implementation of display_set() exists in U-Boot.

Eliminate the `display` command as well as the accompanying files.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2019-05-28 18:55:08 -04:00
Heinrich Schuchardt
dab8788a8c cmd: add exception command
The 'exception' command allows to test exception handling.

This implementation supports ARM, x86, RISC-V and the following exceptions:
* 'breakpoint' - prefetch abort exception (ARM 32bit only)
* 'unaligned'  - data abort exception (ARM only)
* 'undefined'  - undefined instruction exception

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-04-22 12:06:39 -04:00
Michael Walle
82a00be353 cmd: add wdt command
Add a command to control the watchdog devices. This is useful if the
watchdog is rather long running (eg. seconds) and it should be
controlled by scripts. It is also handy during debugging.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-04-12 07:04:18 +02:00
AKASHI Takahiro
59df7e7e77 cmd: add efidebug command
Currently, there is no easy way to add or modify UEFI variables.
In particular, bootmgr supports BootOrder/BootXXXX variables, it is
quite hard to define them as u-boot variables because they are represented
in a complicated and encoded format.

The new command, efidebug, helps address these issues and give us
more friendly interfaces:
 * efidebug boot add: add BootXXXX variable
 * efidebug boot rm: remove BootXXXX variable
 * efidebug boot dump: display all BootXXXX variables
 * efidebug boot next: set BootNext variable
 * efidebug boot order: set/display a boot order (BootOrder)

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-02-25 12:47:13 +01:00
AKASHI Takahiro
49d81fdfb8 cmd: env: add "-e" option for handling UEFI variables
"env [print|set] -e" allows for handling uefi variables without
knowing details about mapping to corresponding u-boot variables.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-02-25 12:47:13 +01:00
Ismael Luceno Cortes
2d3beff2d2 cmd: pcmcia: Build only if CONFIG_CMD_PCMCIA=y
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
2019-02-19 16:58:24 -05:00
Tom Rini
6df41b1cf3 cmd: Move the "dm" command from test/dm/ to cmd/
The "dm" command under CONFIG_CMD_DM should live under cmd/ rather than
test/dm/ so move it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-12-15 11:49:19 -05:00
Anatolij Gustschin
4e92e60d35 cmd: add clear screen 'cls' command
Add common clear screen command for configurations
CONFIG_DM_VIDEO, CONFIG_LCD and CONFIG_CFB_CONSOLE.

Remove the existing cls command implementation from
lcd.c code and activate the command for all boards
enabling CONFIG_LCD for compatibility reasons.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Patrick.Delaunay <patrick.delaunay@free.fr>
2018-12-04 19:44:57 +01:00
Simon Glass
d66ddafaf9 sandbox: Add a new 'sb' command
The old 'sb' command was deprecated in 2015 and replaced with 'host'. It
is useful to be able to access some internal sandbox state, particularly
for testing.

Resurrect the old command and provide a way to print some basic state
information (currently just the arguments to sandbox).

Signed-off-by: Simon Glass <sjg@chromium.org>
2018-11-26 08:25:36 -05:00
Patrice Chotard
d5a8313905 cmd: pinmux: Add pinmux command
pinmux command allows to :
 - list all pin-controllers available on platforms
 - select a pin-controller
 - display the muxing of all pins of the current pin-controller
   or all pin-controllers depending of given options

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
cmd: pinmux: Fix pinmux command

if "pinmux status" command is used without having
set dev using "pinmux dev", print pinmux usage
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-16 16:51:56 -05:00
Tuomas Tynkkynen
78e12901f3 virtio: cmd: Add virtio command for virtio devices
Add 'virtio' command in U-Boot command line.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-11-14 09:16:27 -08:00
Patrick Delaunay
be6eb23931 cmd: remove CONFIG_SOURCE support in Makefile
This line is no more needed and can be removed.

Only CONFIG_CMD_SOURCE is defined in Kconfig and
used in defconfig files.

CONFIG_SOURCE if not defined in source code and
"config SOURCE" is not present in any Kconfig.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2018-11-01 10:02:43 -04:00
Tom Rini
592cd5defd Merge branch 'master' of git://git.denx.de/u-boot-spi
This is the PR for SPI-NAND changes along with few spi changes.

[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-02 17:01:46 -04:00
Miquel Raynal
5db66b3aee cmd: mtd: add 'mtd' command
There should not be a 'nand' command, a 'sf' command and certainly not
a new 'spi-nand' command. Write a 'mtd' command instead to manage all
MTD devices/partitions at once. This should be the preferred way to
access any MTD device.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-10-02 22:12:32 +05:30
Tom Rini
b592936d35 Merge branch 'master' of git://git.denx.de/u-boot-video
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-29 22:28:44 -04:00
Eugen Hristev
d05266f7c5 w1: add command for onewire protocol
Add basic command for bus information and read for onewire
bus using Dallas 1-Wire protocol.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
2018-09-28 20:22:36 -04:00
Mario Six
3bf65cb56c cmd: Add osd commands
Add command to query information from and write text to on-screen
display (OSD) devices.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-28 18:27:33 +02:00
Heinrich Schuchardt
29cfc096a7 cmd: add conitrace command
The 'conitrace' command prints the codes received from the console input as
hexadecimal numbers.

This developer utility is useful for testing the handling of special keys
by keyboard drivers.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2018-09-25 21:49:18 -04:00
Konstantin Porotchkin
3c2a3897e8 fix: cmd: mvebu: Exclude mvebu commands from SPL builds
Exclude mvebu commands from SPL builds

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2018-09-19 13:54:14 +02:00
Tom Rini
15fd1b7903 Merge branch 'master' of git://git.denx.de/u-boot-usb 2018-08-24 16:11:01 -04:00
Jean-Jacques Hiblot
49c752c93a cmd: Add bind/unbind commands to bind a device to a driver from the command line
In some cases it can be useful to be able to bind a device to a driver from
the command line.
The obvious example is for versatile devices such as USB gadget.
Another use case is when the devices are not yet ready at startup and
require some setup before the drivers are bound (ex: FPGA which bitsream is
fetched from a mass storage or ethernet)

usage example:

bind usb_dev_generic 0 usb_ether
unbind usb_dev_generic 0 usb_ether
or
unbind eth 1

bind /ocp/omap_dwc3@48380000/usb@48390000 usb_ether
unbind /ocp/omap_dwc3@48380000/usb@48390000

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-08-21 16:21:37 +02:00
Sam Protsenko
d03e76af5c cmd: Add dtimg command
dtimg command allows user to work with Android DTB/DTBO image format.
Such as, getting the address of desired DTB/DTBO file, printing the dump
of the image in U-Boot shell, etc.

This command is needed to provide Android boot with new Android DT image
format further.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-08-20 07:21:29 -04:00
Mario Six
37c4a5f6a5 cmd: Add axi command
Add a command to debug the AXI bus.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-08-11 09:16:08 +02:00
Lothar Felten
d8970dae27 net: Add new wol command - Wake on LAN
Add a new command 'wol': Wait for an incoming Wake-on-LAN packet or
time out if no WoL packed is received.
If the WoL packet contains a password, it is saved in the environment
variable 'wolpassword' using the etherwake format (dot or colon
separated decimals).

Intended use case: a networked device should boot an alternate image.
It's attached to a network on a client site, modifying the DHCP server
configuration or setup of a tftp server is not allowed.
After power on the device waits a few seconds for a WoL packet. If a
packet is received, the device boots the alternate image. Otherwise
it boots the default image.

This method is a simple way to interact with a system via network even
if only the MAC address is known. Tools to send WoL packets are
available on all common platforms.

Some Ethernet drivers seem to pad the incoming packet. The additional
padding bytes might be recognized as Wake-on-LAN password bytes.

By default enabled in pengwyn_defconfig.

Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-02 14:14:20 -05:00
Igor Opaniuk
60b2f9e7b9 cmd: avb2.0: avb command for performing verification
Enable a "avb" command to execute Android Verified
Boot 2.0 operations. It includes such subcommands:
  avb init - initialize avb2 subsystem
  avb read_rb - read rollback index
  avb write_rb - write rollback index
  avb is_unlocked - check device lock state
  avb get_uuid - read and print uuid of a partition
  avb read_part - read data from partition
  avb read_part_hex - read data from partition and output to stdout
  avb write_part - write data to partition
  avb verify - run full verification chain

Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
2018-06-18 13:55:13 -04:00
Miquel Raynal
ff32245bb3 tpm: prepare support for TPMv2.x commands
Choice between v1 and v2 compliant functions is done with the
configuration.

Create the various files that will receive TPMv2-only code on the same
scheme as for the TPMv1 code.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2018-05-25 20:12:55 -04:00
Miquel Raynal
d677bfe2f7 tpm: disociate TPMv1.x specific and generic code
There are no changes in this commit but a new organization of the code
as follow.

* cmd/ directory:
        > move existing code from cmd/tpm.c in cmd/tpm-common.c
	> move specific code in cmd/tpm-v1.c
	> create a specific header file with generic definitions for
	  commands only called cmd/tpm-user-utils.h

* lib/ directory:
        > move existing code from lib/tpm.c in lib/tpm-common.c
	> move specific code in lib/tpm-v1.c
	> create a specific header file with generic definitions for
	  the library itself called lib/tpm-utils.h

* include/ directory:
        > move existing code from include/tpm.h in include/tpm-common.h
	> move specific code in include/tpm-v1.h

Code designated as 'common' is compiled if TPM are used. Code designated
as 'specific' is compiled only if the right specification has been
selected.

All files include tpm-common.h.
Files in cmd/ include tpm-user-utils.h.
Files in lib/ include tpm-utils.h.
Depending on the specification, files may include either (not both)
tpm-v1.h or tpm-v2.h.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix a few more cases of tpm.h -> tpm-v1.h, some Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-25 20:12:55 -04:00
Miquel Raynal
9f9ce3c369 tpm: prepare introduction of TPMv2.x support in Kconfig
Because both major revisions are not compatible at all, let's make them
mutually exclusive in Kconfig. This way we will be sure, when using a
command or a library function that it is supported by the right
revision.

Current drivers are currently prefixed by "tpm_", we will prefix TPMv2.x
files by "tpm2_" to make the distinction without moving everything.

The Kconfig menu about TPM drivers is now divided into two sections, one
for each specification. Compliant drivers with one specification will
only show up if this specification _only_ has been selected, otherwise a
comment is displayed.

Once a driver is selected by the user, it selects automatically a
boolean value, that is needed in order to activate the TPM commands.
Selecting the TPM commands will automatically select the right
command/library files.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework deps as TPM_V1 and TPM_V2 depend on TPM,
        drop TPM_DRIVER_SELECTED]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-25 20:12:33 -04:00
Alex Kiernan
b11ed7d602 bootcount: Add bootcount command
Add a command to manipulate the bootcounter. This is useful if you can
run device recovery from inside U-Boot and need to reset the bootcounter
after executing that process as part of altbootcmd.

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2018-05-23 17:30:05 -04:00
Neil Armstrong
051ebe3228 cmd: add ADC cli commands
Add an 'adc' cli command to get information from adc devices and to read
"single shot" data.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2018-05-08 18:50:23 -04:00
Michalis Pappas
666028fc7c arm64: Add SMC and HVC commands
This patch adds smc and hvc commands, that allow issuing Secure Monitor
Calls and Hypervisor Calls conforming to the ARM SMC Calling Convention.

Add Kconfig items to allow each command can be individually enabled.

Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-05-08 09:07:35 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Mario Six
55b2556115 cmd: Add command for calculating binary operations
This patch adds a command that enables the calculation of bit operations
(AND, OR, XOR) on binary data from the command line. Memory locations as
well as the contents of environment variables are eligible as sources
and destination of the binary data used in the operations.

The possible applications are manifold: Setting specific bits in
registers using the regular read-OR-write pattern, masking out bits in
bit values, implementation of simple OTP encryption using the XOR
operation, etc.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-06 20:45:44 -04:00
Tuomas Tynkkynen
a4fa811463 cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA
cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

 # CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-05 20:58:11 -05:00
Lokesh Vutla
5cd9661dc6 arm: keystone: Move cmd_ddr3 to a common place
Move cmd_ddr3 to cmd/ti in order to make
it build for non-keystone TI platforms.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rename to ddr3.c not cmd_ddr3.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-01-19 15:49:26 -05:00
Eddie Cai
453c95e01a usb: rockchip: add rockusb command
this patch add rockusb command. the usage is
rockusb <USB_controller> <devtype> <dev[:part]>
e.g. rockusb 0 mmc 0

Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-01-10 11:11:06 +01:00
Tom Rini
8e18f34c28 x86: Move commands from under arch/x86 to cmd/x86/
We only need to compile and link these files when building for full
U-Boot.  Move them to under cmd/x86/ to make sure they aren't linked in
and undiscarded due to u_boot_list_2_cmd_* being included).

Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2018-01-08 16:52:22 +08:00
Simon Glass
d5f61f272d log: Add a 'log level' command
Add a command for adjusting the log level.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-12-07 15:17:00 -05:00
Simon Glass
c5404b64fb Drop the log buffer
This does not appear to be used by any boards. Before introducing a new
log system, remove this old one.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-12-07 15:17:00 -05:00
Marek Behún
9d84550955 cmd: Add the 'btrsubvol' command to list BTRFS subvolumes
Signed-off-by: Marek Behun <marek.behun@nic.cz>

 create mode 100644 cmd/btrfs.c
2017-10-02 21:52:18 -04:00
Stefan Agner
2f005695df cmd: add sdp command
Add a new command to start USB Serial Download Protocol (SDP)
state machine.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-08-23 10:41:58 +02:00
Simon Glass
4395f66739 dm: blk: Add a generic function for block device commands
Most block devices provide a command (e.g. 'sata', 'scsi', 'ide') and
these commands generally do the same thing. This makes it harder to
maintain this code and keep it consistent.

We now have a block device interface which is either implemented by driver
model (when CONFIG_BLK is enabled) or with a legacy interface. Therefore
it is possible to handle most of what these commands do with generic code.

Add a new generic function to process block-device commands using the
interface type and the current device number for that type.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:16 +09:00
Zhikang Zhang
0adc38be3d nvme: Add nvme commands
Add nvme commands in U-Boot command line.

1. "nvme scan" - scan NVMe blk devices
2. "nvme list" - show all available NVMe blk devices
3. "nvme info" - show current or a specific NVMe blk device
4. "nvme device" - show or set current device
5. "nvme part" - print partition table
6. "nvme read" - read data from NVMe blk device
7. "nvme write" - write data to NVMe blk device

Signed-off-by: Zhikang Zhang <zhikang.zhang@nxp.com>
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-13 15:17:32 -04:00
Simon Glass
7a76431845 Convert CONFIG_CMD_YAFFS2 to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_YAFFS2

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 17:44:50 -04:00
Simon Glass
0941f597a2 Convert CONFIG_CMD_SCSI to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_SCSI

Also update the Makefile to use CONFIG_CMD_SCSI instead of CONFIG_SCSI to
enable the command, fixing an earlier error.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Rework to default y if SCSI, drop cl-som-am57x which did not use
CMD_SCSI for real]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-11 15:41:55 -04:00
Simon Glass
6f62d7c4f7 Kconfig: Drop CONFIG_CMD_PORTIO and associated command
This command is not used by any board. It also looks quite similar to the
'iod' and 'iow' commands which use the correct I/O macros.

Drop it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:52 -04:00
Heiko Schocher
98f705c9ce powerpc: remove 4xx support
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.

Signed-off-by: Heiko Schocher <hs@denx.de>
2017-07-03 17:35:28 -04:00
Tom Rini
18b2916585 cmd/ethsw: Disable implicit enum conversion warning
With clang-3.8 we see warnings like:
cmd/ethsw.c:304:6: warning: implicit conversion from
      enumeration type 'enum ethsw_keyword_opt_id' to different enumeration type
      'enum ethsw_keyword_id' [-Wenum-conversion]
                                        ethsw_id_pvid_no,
                                        ^~~~~~~~~~~~~~~~

Because we have one enum for ethsw_keyword_id and a second enum for
ethsw_keyword_opt_id.  This ends up being safe as ethsw_keyword_opt_id
explicitly starts after ethsw_keyword_id enum ends.   Disable the
warning here rather than collapse these into one enum and rely on
comments to denote where optional keywords begin.

Cc: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-06-05 14:13:12 -04:00