This change has 3 goals:
- Have secondary cores be released into spin loops at their 'true'
address in SDRAM. Previously, secondary cores were put into spin
loops in the 0xfffffxxx address range which required that boot page
translation was always enabled while cores were in their spin loops.
- Allow the TLB window that the primary core uses to access the
secondary cores boot page to be placed at any address. Previously, a
TLB window at 0xfffff000 was always used to access the seconary cores'
boot page. This TLB address requirement overlapped with other
peripherals on some boards (eg XPedite5370). By default, the boot
page TLB will still use the 0xfffffxxx address range, but this can be
overridden on a board-by-board basis by defining a custom
CONFIG_BPTR_VIRT_ADDR. Note that the TLB used to map the boot page
remains in use while U-Boot executes. Previously it was only
temporarily used, then restored to its initial value.
- Allow Boot Page Translation to be disabled on bootup. Previously,
Boot Page Translation was always left enabled after secondary cores
were brought out of reset. This caused the 0xfffffxxx address range
to somewhat "magically" be translated to an address in SDRAM. Some
boards may not want this oddity in their memory map, so defining
CONFIG_MPC8xxx_DISABLE_BPTR will turn off Boot Page Translation after
the secondary cores are initialized.
These changes are only applicable to 85xx boards with CONFIG_MP defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CoreNet platform style of bringing secondary cores out of reset is
a bit different that the PQ3 style. Mostly the registers that we use
to setup boot translation, enable time bases, and boot release the cores
have moved around.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Its possible that we try and copy the boot page code out of flash into a
DDR location that doesn't have a TLB cover it. For example, if we have
3G of DDR we typically only map the first 2G. In the cases of 4G+ this
wasn't an issue since the reset page TLB mapping covered the last page
of memory which we wanted to copy to.
We now change the physical address of the reset page TLB to map to the
true physical location of the boot page code, copy and than set the
TLB back to its 1:1 mapping of the reset page.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The number of CPUs are getting detected dynamically by checking the
processor SVR value. Also removed CONFIG_NUM_CPUS references from all
the platforms with 85xx/86xx processors.
This can help to use the same u-boot image across the platforms.
Also revamped and corrected few Freescale Copyright messages.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Match determine_mp_bootpg() that was added for 86xx. We need this to
address a bug introduced in v2009.03 with 86xx MP booting. We have to
make sure to reserve the region of memory used for the MP bootpg() so
other u-boot code doesn't use it.
Also added a comment about how cpu_reset() is dealing w/an errata on
early 85xx MP HW.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_NUM_CPUS to match existing define used by 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
* adjust __spin_table alignment to match ePAPR v0.94 spec
* loop over all cpus when determing who is up. This fixes an issue if
the "boot cpu" isn't core0. The "boot cpu" will already be in the
cpu_up_mask so there is no harm
* Added some protection in the code to ensure proper behavior. These
changes are explicitly needed but don't hurt:
- Added eieio to ensure the "hot word" of the table is written after
all other table updates have occurred.
- Added isync to ensure we don't prefetch loading of table entries
until we a released
These issues we raised by Dave Liu.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We were looking at the wrong memory offset to determine of a secondary
cpu had been spun up or not. Also added a warning message if the
all the secondary cpus we expect don't spin up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Provide a board_lmb_reserve helper function to ensure we reserve
the page of memory we are using for the boot page translation code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following changes are needed to be inline with ePAPR v0.81:
* r4, r5 and now always set to 0 on boot release
* r7 is used to pass the size of the initial map area (IMA)
* EPAPR_MAGIC value changed for book-e processors
* changes in the spin table layout
* spin table supports a 64-bit physical release address
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added the cpu command that provides a generic mechanism to get status,
reset, and release secondary cores in multicore processors.
Added support for using the ePAPR defined spin-table mechanism on 85xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
