Add test case for 'fdt get value' sub command.
The test case can be triggered using:
"
./u-boot -d u-boot.dtb -c 'ut fdt'
"
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Always increment both the iterator and pointer into the string
property value by length of the current element + 1 (to cater
for the string delimiter), otherwise the element extracted from
the string property value would be extracted from an offset that
is multiple of the length of the first element, instead of sum
of element lengths until select index.
This fixes 'fdt get value' operation for index above 1 (counting
from index 0).
Acked-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Fixes: 13982ced2c ("cmd: fdt: Add support for reading stringlist property values")
Signed-off-by: Marek Vasut <marex@denx.de>
The sandbox config file is to be removed. Move the GUID declarations
needed for capsule update functionality to the board file where they
are used.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Invoking lseek() may result in an error. Handle it.
Addresses-Coverity-ID: 376212 ("Error handling issues (CHECKED_RETURN)")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add a new flag to buildman so that we will in turn pass
BINMAN_ALLOW_MISSING=1 to 'make'. Make use of this flag in CI.
Allow the settings file to control this.
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This was dropped my mistake. Reinstate it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: d829f1217c ("bulidman: Add support for a simple build")
While it is possible and documented on how to re-run buildman to replace
faked required binary files after the fact, this behavior ends up being
more confusing than helpful in practice. Switch to requiring
BINMAN_ALLOW_MISSING=1 to be passed on the 'make' line to enable this
behavior.
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
These are documented in various several sections. Add a new section that
mentions them all in one place so it is easier to see what environment
variables can be used to control U-Boot's use of binman.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Buildman should consider a build as a success (with warnings) if missing
blobs have been dealt with by binman, even though buildman itself returns
and error code overall. This is how other warnings are dealt with.
We cannot easily access the 103 exit code, so detect the problem in the
output.
With this change, missing blobs result in an exit code of 101, although
they still indicate failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support for some architectures has been removed since buildman was first
written. Also all toolchains are now available at kernel.org so we don't
need the links, except for arc where the kernel.org toolchain fails to
build all boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
The settings file omits a few lines which are useful for getting every
board building. Add these and update the documentation tool.
Signed-off-by: Simon Glass <sjg@chromium.org>
This script was removed about 6 years ago so most people should be aware
that it is not needed anymore. Drop mention of it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert the buildman documentation to rST format and include it in the
'build' section.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Quentin Schulz <foss+uboot@0leil.net>
At present binman returns success when told to handle missing/faked blobs
or missing bintools. This is confusing since in fact the resulting image
cannot work.
Use exit code 103 to signal this problem, with a -W option to convert
it to a warning.
Rename the flag to --ignore-missing since it controls bintools also.
Add documentation about exit codes while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
This currently uses if_changed on a phony target. Use a real file as the
target and add FORCE at the end, as required. Drop the 'inputs' phony
since it is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
gcc 12 seems to warn on strncpy() as a matter of course. Rewrite the code
a different way to do the same thing, to avoid the warning.
Signed-off-by: Simon Glass <sjg@chromium.org>
This reverts commit daa2da754a.
This commit is not needed anymore since the btool_ prefix is
automatically stripped by bintool.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The binary is looked on the system by the suffix of the packer class.
This means binman was looking for btool_gzip on the system and not gzip.
Since a btool can have its btool_ prefix missing but its module and
binary presence on the system appropriately found, there's no need to
actually keep this prefix after listing all possible btools, so let's
remove it.
This fixes gzip btool by letting Bintool.find_bintool_class handle the
missing prefix and still return the correct class which is then init
with gzip name instead of btool_gzip.
Additionally, there was an issue with the cached module global variable.
The variable only stores the module and not the associated class name
when calling find_bintool_class.
This means that when caching the module on the first call to
find_bintool_class, class_name would be set to Bintoolbtool_gzip but the
module_name gzip only, adding the module in the gzip key in the module
dictionary. When hitting the cache on next calls, the gzip key would be
found, so its value (the module) is used. However the default class_name
(Bintoolgzip) is used, failing the getattr call.
Instead, let's enforce the same class name: Bintool<packer>, whatever
the filename it is contained in.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sync of device-tree/bindings in 11a48a5a18c6 ("Linux 5.6-rc2") causes
Ethernet to break on some GXBB boards; the PHY seems to need proper reset
timing to function in u-boot and Linux. Re-add the old PHY reset binding
for dwmac until we support new bindings in the PHY node. This borrows the
same fix applied to the Odroid C2 board [0].
[0] https://lists.denx.de/pipermail/u-boot/2021-April/446658.html
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20221025143205.14470-1-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Implement setbrg in amlogic/meson serial device with driver model
similar to how the meson_uart.c driver does it in Linux. Also
configure (probe) the serial device with the new reg5 register.
Signed-off-by: Edoardo Tomelleri <e.tomell@gmail.com>
Link: https://lore.kernel.org/r/20220918161701.572814-1-e.tomell@gmail.com
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support octal spi flash and uses DCC terminal
for console output. Add required dts for octal spi flash mini u-boot
configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When cadence_qspi_versal_flash_reset() function is called in mini
u-boot where there is no firmware support, it is missing defines for
macro's BOOT_MODE_POR_0 & BOOT_MODE_POR_1. Remove them and replace with
already define macro's which have same values as these.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support qspi flash and uses DCC terminal
for console output. Add required dts files for qspi mini configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add soc_xilinx_versal_net driver to identify the family & revision of
versal-net SoC. Add Kconfig option CONFIG_SOC_XILINX_VERSAL_NET to
enable/disable this driver. To enable this driver by default, add this
config to xilinx_versal_net_virt_defconfig file. This driver will be
probed using platdata U_BOOT_DEVICE structure which is specified in
mach-versal-net/cpu.c.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/613d6bcffd9070f62cf348079ed16c120f8fc56f.1668612993.git.michal.simek@amd.com
Versal NET mini U-Boot configuration is used for memory testing that's why
load address can't be really placed in memory which doesn't need to work
that's why move it to start of OCM which is the same memory which U-Boot is
running from.
Signed-off-by: Michal Simek <michal.simek@amd.com>
vck190 system controller low level setup is the same for revB that's why
also create symlink to revA.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Use dot instead of comma. The fix doesn't affect anything but it is good to
be aligned with used pattern. The first is used only for string size
calculation and the second change is in the comment.
Fixes: db681d4929 ("net: phy: Add new read ethernet phy id function")
Signed-off-by: Michal Simek <michal.simek@amd.com>
The fclk-enable property is set to 0 which disables all FCLKs.
Enable all FCLKs so they can be used as clock sources in the
programmable logic.
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b1308dc1f14f8eb24662019f7376c959e5e763b8.1665567031.git.michal.simek@amd.com
Current xilinx_timer_get_count() implementation does not take into account
the periodic 32-bit wrap arounds, as it directly returns the 32-bit counter
register value. The roll-overs cause problems in the upper timer layers, as
generic timer code expects an incrementing 64-bit value from get_count() to
work correctly.
Add the missing 64-bit up-conversion to fix random hangs/delays in
__udelay().
Fixes: a36d86720f ("microblaze: Convert axi timer to DM driver")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221012053656.1492457-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Relocate timer_ops pointers when CONFIG_NEEDS_MANUAL_RELOC is enabled.
The (gd->flags & GD_FLG_RELOC) check was added to make sure the reloc_done
logic works for drivers that use DM_FLAG_PRE_RELOC.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20221012053656.1492457-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Align timer uclass with the other subsystems and provide a timer_get_ops()
convenience macro.
Using this instead of the generic device_get_ops() also prevents
-Wdiscarded-qualifiers warnings when used with non-const variables.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20221012053656.1492457-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Removing the zynq_board_read_rom_ethaddr() function as
xlnx,eeprom is not used anymore. As all board dts to use
nvmem alias instead of xlnx,eeprom.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221017094818.17996-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Axi qspi controller supports 32-bit & 24-bit addressing modes
for micron, macronix & spansion flash parts. But for winbond
flashes it only supports 24-bit addressing mode.
Enable CONFIG_SPI_FLASH_BAR to use extended addressing mode
to make 32-bit addressing mode work on all flashes.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/f3864966c8ddd766a1702ad61b0e008a1f57462f.1665565423.git.michal.simek@amd.com
This commit adds the menu-driven interface to show the
signature list content.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit adds the menu-driven UEFI Secure Boot Key
enrollment interface. User can enroll PK, KEK, db
and dbx by selecting file.
Only the signed EFI Signature List(s) with an authenticated
header, typically '.auth' file, is accepted.
To clear the PK, KEK, db and dbx, user needs to enroll the null key
signed by PK or KEK.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
EFI_SIMPLE_FILE_SYSTEM_PROTOCOL is not always provided
by U-Boot. Use protocol interface functions instead of
U-Boot internal functions.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
