Warnings:
board/xilinx/zynq/board.c:17:13: warning: symbol 'fpga' was not declared. Should it be static?
board/xilinx/zynq/board.c:20:13: warning: symbol 'fpga010' was not declared. Should it be static?
board/xilinx/zynq/board.c:21:13: warning: symbol 'fpga015' was not declared. Should it be static?
board/xilinx/zynq/board.c:22:13: warning: symbol 'fpga020' was not declared. Should it be static?
board/xilinx/zynq/board.c:23:13: warning: symbol 'fpga030' was not declared. Should it be static?
board/xilinx/zynq/board.c:24:13: warning: symbol 'fpga045' was not declared. Should it be static?
board/xilinx/zynq/board.c:25:13: warning: symbol 'fpga100' was not declared. Should it be static?
board/xilinx/zynq/board.c:120:5: warning: symbol 'board_mmc_init' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPL is using ps7_init.c/h files which are generated
from design tools which have to be copied to
boards/xilinx/zynq folder before compilation.
BSS section is moved to SDRAM because fat support
requires more space than SRAM size.
Added:
- MMC and QSPI support
- Boot OS directly from SPL
- Enable SPL command
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Added support to find the bootmodes by reading
slcr bootmode register. this can be helpful to
autoboot the configurations w.r.t a specified bootmode.
Added this functionality on board_late_init as it's not
needed for normal initializtion part.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Zynq can have axi ethernet and emaclite IPs in programmable
logic.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
The first 1MB is not initialized by first stage bootloader.
Check if memory is setup to 16bit mode and ECC is enabled.
If it is, clear the first 1MB.
Also u-boot should report only the half size of memory.
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Add support for zc7100 device.
- FPGA programming on few of the SOC(zc7100) takes more
than 1sec, hence increased the program time by 4sec to
sync' all soc's.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Devcfg device requires to load bitstream in binary format.
But u-boot also has an option for loading bitstream in bit
format. Let's handle both cases by zynqpl driver.
Also add suport for loading partial bitstreams.
The first driver version was done by:
Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Avoid overwriting GEMx_RCLK_CTRL and GEMx_CLK_CTRL
if the Ethernet interface is connect on EMIO
Do not enable emio for this standard board configuration for now.
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Pass the PHY address to the driver init to
allow parallel use of both interfaces
Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add all fixed addresses to hardware.h and change petalinux
configuration to support this.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
All these files was used for ancient xilinx drivers
which are finally gone.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
Add support for Xilinx Zynq board.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
CC: Joe Hershberger <joe.hershberger@gmail.com>
