ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add pinctrl macros for AM64 SoC. These macro definitions are similar to
that of previous platforms, but adding new definitions to avoid any
naming confusions in the soc dts files.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
In CP115, comphy4 can be configured into SFI port1
(in addition to SFI0). This patch adds the option
described above.
In addition, rename all existing SFI/XFI references:
COMPHY_TYPE_SFI --> COMPHY_TYPE_SFI0
No functional change for exsiting configuration.
Change-Id: If9176222e0080424ba67347fe4d320215b1ba0c0
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Even if comphy types of SATA2/SATA3/SGMII3 and comphy speeds of
1.5G/3G/6.25G were referenced in the driver non configuration (dts)
was using it.
This patch removes unused definitions.
Change-Id: I53ed6f9d3a82b9d18cb4e488bc14d3cf687f9488
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Currently, all comphy definitions are PHY_TYPE_XX and PHY_SPEEED_XX.
Those definition might be confused with MDIO PHY definitions.
This patch does the following changes:
- PHY_TYPE_XX --> COMPHY_TYPE_XX
- PHY_SPEED_XX --> COMPHY_SPEED_XX
This improves readability, no functional change.
Change-Id: I2bd1d9289ebbc5c16fa80f9870f797ea1bcaf5fa
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
- For some Marvell SoCs, like armada-3700, there are both
USB host and device controller, but on PHY level the
configuration is the same.
- The new type supports both USB device and USB host
- This patch is cherry-picked from u-boot-2015 as-is.
Change-Id: I01262027edd8ec23391cff6fb409b3009aedfbb9
Signed-off-by: jinghua <jinghua@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Update R40 .dts{,i} and dt-binding headers to current version from kernel.
Files taken from Linux 5.12-rc1 release
(commit fe07bfda2fb9cdef8a4d4008a409bb02f35f1bd8)
Signed-off-by: Ivan Uvarov <i.uvarov@cognitivepilot.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add power domain nodes to DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
-----BEGIN PGP SIGNATURE-----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=4VxR
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
This patchset has following changes:
- introduce stm32h750.dtsi to support stm32h750 value line
- add pin groups for usart3/uart4/spi1/sdmmc2
- add stm32h750i-art-pi.dtb (arch/arm/boot/dts/Makefile)
- add stm32h750i-art-pi.dts to support art-pi board
- add stm32h750i-art-pi-u-boot.dtsi to support art-pi board (u-boot)
art-pi board component:
- 8MiB qspi flash
- 16MiB spi flash
- 32MiB sdram
- ap6212 wifi&bt&fm
the detail board information can be found at:
https://art-pi.gitee.io/website/
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:
- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA
but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is the state as of v5.10 in Linux.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The EK874 development kit from Silicon Linux is made of CAT874 (the main
board) and CAT875 (the sub board that goes on top of CAT874).
This patch adds the required board support to boot Si-Linux EK874 board
based on R8A774C0 SoC.
DTS files apart from r8a774c0-ek874-u-boot.dts and r8a774c0-u-boot.dtsi
have been imported from Linux kernel 5.11 commit f40ddce88593
("Linux 5.11").
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
The versaclock doesn't have a driver yet, but there are a bunch
of device tree updates for the Beacon RZ/G2 boards that won't
compile without these. A driver is coming, so sync the bindings
for now
Signed-off-by: Adam Ford <aford173@gmail.com>
Sync all J721e related v5.11-rc6 Linux kernel dts into U-Boot.
HBMC nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid any regressions, hbmc nodes are kept
intact. These will be added in kernel in future.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This commit introduces H616 DTSI file and dt-bindings headers needed for
device tree files.
Files are taken from v3 Linux H616 support submission[1], as the
H616 .dtsi file is not merged upstream yet.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632082.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAOkP8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKedCACiDHgP71VKSOiYnEU4
vHD/ANmfMXqnsL71PpSdagnBRAl4vpm46CnD+Mq7RtchxGDNufX6tWJSI04Ci0bC
mfmIfVEjePOnuUayylJ55OlrtJVpBqJFPqxM6MFcIF7nRja1r5thV1jTLNu+b4sm
gg2sk1mC/531Lxbk8S7x+diPymNRArEm3IEw+xEqUhsNVQCKjOEcxi/BWIB2prR3
NxRSGdW3j4CKdBqt7uOL1bqApeQQ9m0/gm1tE3hMXUo09I7uXmb7U52aKb5cV8L+
8ZOlbav6yaPACe3p9npp4K0ByXMmYHjeo1NZW4cvAoKfzragdu0Cv7f0ssVCgrlR
p1e3
=xS6A
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.04 cycle
This feature set includes macb updates for all interfaces and new
sama7g5 variant support; micrel ksz9031 DLL support; a new board from
Giant based on Adafruit feather form factor which contains a SAMA5D27
SoC; several fixes regarding the NAND flash PMECC block; and pincontrol
drive strength support for pio4 controller.
This patch adds a clock driver for MediaTek MT7620 SoC.
This driver provides clock gate control as well as getting clock frequency
for CPU/SYS/XTAL and some peripherals.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add controller reset support through the
System Control Unit (SCU) of AST2600 SoC.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
This patch adds the clock control driver
for the AST2600 SoC.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Add clock driver code for the Microchip PolarFire SoC. This driver
handles reset and clock control of the Microchip PolarFire SoC device.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Add support for PRUSS SYSC type:
The PRUSS module has a SYSCFG which is unique. The SYSCFG has two
additional unique fields called STANDBY_INIT and SUB_MWAIT in addition
to regular IDLE_MODE and STANDBY_MODE fields. Add the bindings for this
new sysc type.
Add support for MCAN on dra76x:
The dra76x MCAN generic interconnect module has a its own format for the
bits in the control registers.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Handle the register RCC_MP_GCR without SET/CLR registers
but with a direct access to bit BOOT_MCU:
- deassert => set the bit: The MCU will not be in HOLD_BOOT
- assert => clear the bit: The MCU will be set in HOLD_BOOT
With this patch the RCC driver handles the MCU_HOLD_BOOT_R value
added in binding stm32mp1-resets.h
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Import updated device trees from Linux tag v5.9. This picks up new
hardware (PinePhone, PineTab); and it drops the U-Boot specific DTSI
files for the Pinebook and the Teres-I, since the ANX6345 bridge is
now supported upstream.
A couple of headers needed updates for recently-added hardware support.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
Add a new subsystem that handles multiplexer controllers. The API is the
same as in Linux.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[trini: Update some error calls to use different functions or pass
correct arguments]
Signed-off-by: Tom Rini <trini@konsulko.com>
The System Control Unit (SCU) controller of Aspeed
SoCs provides the reset control for each peripheral.
This patch refactors the reset method to leverage
the SCU reset control. Thus the driver dependency
on watchdog including dedicated WDT API and reset
flag encoding can be eliminated.
The Kconfig description is also updated accordingly.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The Fully-Programmable Input/Output Array (FPIOA) device controls pin
multiplexing on the K210. The FPIOA can remap any supported function to any
multifunctional IO pin. It can also perform basic GPIO functions, such as
reading the current value of a pin. However, GPIO functionality remains
largely unimplemented (in favor of the dedicated GPIO peripherals).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This extends the pinctrl-sandbox driver to support pin muxing, and adds a
test for that behaviour. The test is done in C and not python (like the
existing tests for the pinctrl uclass) because it needs to call
pinctrl_select_state. Another option could be to add a command that
invokes pinctrl_select_state and then test everything in
test/py/tests/test_pinmux.py.
The pinctrl-sandbox driver now mimics the way that many pinmux devices
work. There are two groups of pins which are muxed together, as well as
four pins which are muxed individually. I have tried to test all normal
paths. However, very few error cases are explicitly checked for.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
-----BEGIN PGP SIGNATURE-----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=rbAX
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20201005' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- generate unique mac address from SoC serial on S400 board
- Add USB support for GXL and AXG SoCs
- Update Gadget code to use the new GXL and AXG USB glue driver
- Add a VIM3 board support to add dynamic PCIe enable in OS DT
- Fix AXG pinmux with requesting GPIOs
- Add missing GPIOA_18 for AXG pinctrl
- Add Amlogic PWM driver
This imports the G12A & SM1 SoC and boards DT changes from the Linux
commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This imports the AXG, GXL & GXM SoC and boards DT changes from the Linux
commit b3a9e3b9622a ("Linux 5.8-rc1").
This change also removes GXL & GXM u-boot.dtsi hacks for USB gadget.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
Another "virtual" clock (in the sense that it isn't configurable). This
could possibly be done as a clock in the device tree, but I think this is a
bit cleaner.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
Add MSCC header with delay definitions for VSC8531 and associated
family devices.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add pre-requisite headers for AT91 clock architecture. These
are based on already present files on Linux and will be used
by following commits for AT91 CCF clock drivers.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
On Qualcomm IPQ40xx SoC series, GCC clock IP also handles the resets.
So since this will be needed by further drivers, lets add a driver for the reset controller.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Import Qualcomm IPQ4019 GCC bindings from Linux.
This will enable using bindings instead of raw clock numbers both in the driver and DTS like Linux does.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Modify SPDX-License for furture patch warning
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
v2: modify title description aspeed:clock -> clock:aspeed
Use kernel include/dt-bindings/clock/aspeed-clock.h define
for clock driver.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Rename the ast2500-scu.h to aspeed-clock.h.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Reviewed-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Add 4 new phy types which are present in Linux kernel.
DP and SGMII types are used on Xilinx ZynqMP devices.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add bit indexes for reset signals within the PRCI module
on FU540-C000 SoC.
The DDR and ethernet sub-system's have reset signals
indicated by these reset indexes.
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
This patch adds a simple clock driver for the Marvell Octeon MIPS SoC
family. Its for IO clock rate passing via DT in some of the Octeon
driver, like I2C. So that we don't need to use the non-mainline API
octeon_get_io_clock().
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukasz Majewski <lukma@denx.de>
This patch imports the device tree and required bindings to permit
the device tree to build for the R8Z774A1 (RZ/G2M).
Signed-off-by: Adam Ford <aford173@gmail.com>
- New timer API to allow delays with a 32-bit microsecond timer
- Add dynamic ACPI structs (DSDT/SSDT) generations to the DM core
- x86: Enable ACPI table generation by default
- x86: Enable the copy framebuffer on Coral
- x86: A few fixes to FSP2 with ApolloLake
- x86: Drop setup_pcat_compatibility()
- x86: Primary-to-Sideband Bus minor fixes
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXxCxWw8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76bPyACcDZ8gD9jf1P/Zh+7kqrGdIWwURF8AnAiEtNnu
FhE/WQQj4mAEWE4F2bFE
=7ceG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200716' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
i.MX for 2020.10
----------------
- i.MX DDR driver fix/update for i.MX8M
- i.MX pinctrl driver fix.
- Use arm_smccc_smc to remove imx sip function
- i.MX8M clk update
- support booting aarch32 kernel on aarch64 hardware
- fused part support for i.MX8MP
- imx6: pcm058 to DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/708734785
This binding currently has a flags cell but it is not used. Make use of it
to create ACPI tables for interrupts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Add devicetree bindings for the Intel Non-High-Definition-Audio Link Table
(NHLT).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sync DT bindings from kernel DT and move them to out of -u-boot.dtsi
files.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Raspberry Pi 4's co-processor controls some of the board's HW
initialization process, but it's up to Linux to trigger it when
relevant. Introduce a reset controller capable of interfacing with
RPi4's co-processor that models these firmware initialization routines as
reset lines.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Where possible, I have tried to find compatible drivers based on the layout
of registers. However, many devices remain untested. All untested devices
have been left disabled, but some tentative properties (such as compatible
strings, and clocks, interrupts, and resets properties) have been added.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Due to the large number of clocks, I decided to use the CCF. The overall
structure is modeled after the imx code. Clocks parameters are stored in
several arrays, and are then instantiated at run-time. There are some
translation macros (FOOIFY()) which allow for more dense packing.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
CC: Lukasz Majewski <lukma@denx.de>
Add support for configuring the CLK_25M pin as well as the RGMII I/O
voltage by the device tree.
By default the AT803x PHYs outputs the 25MHz clock of the XTAL input.
But this output can also be changed by software to other frequencies.
This commit introduces a generic way to configure this output.
Also the PHY supports different RGMII I/O voltages: 1.5V, 1.8V and 2.5V.
An internal LDO is able to provide 1.5V (default) and 1.8V. The 2.5V
option needs an external supply voltage. This commit adds support to
switch the internal LDO to 1.8V.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
A comment note has been left after completing pinctrl listing, so let's
remove it since it's useless.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
This syncs the rk3328 power domain header file from Linux kernel
next-20200324, to support newer hardware blocks when syncing the
device tree files.
The last non-merge commit to touch it was
b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This syncs the rk3328 clock header file from Linux kernel next-20200324,
to support newer hardware blocks when syncing the device tree files.
The last non-merge commit to touch it was
0dc14b013f79 ("clk: rockchip: add clock id for watchdog pclk on rk3328")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Loic Devulder <ldevulder@suse.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Synchronize R-Car Gen2 device trees with Linux 5.6.2,
commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
-----BEGIN PGP SIGNATURE-----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=e10O
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200428' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix sd-emmc controller A init on G12A/G12B/SM1 SoCs
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
Add support for additional timer clock which belongs to tunnel
domain.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This patch adds .dtsi file(sync with Linux 5.5-rc6 with hash "b3a987b0264d")
and required binding for S700 SoC that is a 64-bit Quad-core ARM
Cortex-A53 cores.
It also provisions dts file to be built based on selected
platform(CONFIG_MACH_S900/S700).
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Synchronize device tree bindings with v5.5-rc6 tag with commit id
"b3a987b0264d".
Also, it removes older clock binding defined for S900 along with undocumented
compatible string "actions,s900-serial" from serial driver and adapts clock
driver to cater to new bindings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Cleanup binding support, use the generic binding by default
(test u-class gpio_xlate_offs_flags function) and add
specific binding for added value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit extends the flags that can be used in GPIO specifiers to
indicate if a pull-up resistor or pull-down resistor should be
enabled.
It is the backport of linux commit ede033e1e863c ('dt-bindings:
gpio: document the new pull-up/pull-down flags')
from Thomas Petazzoni <thomas.petazzoni@bootlin.com>
and integrated in v5.1-rc1
https://github.com/torvalds/linux/commit/ede033e1e863c
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sync the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2")
The only exception to this is the mmc pinctrl pin bias of gxl SoC family.
This is a fix which found its way to u-boot but not Linux yet.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import the common leds bindings definition from linux
d5226fa6dbae ("Linux 5.5")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
So far we have avoided adding a clock driver for Intel devices. But the
Designware I2C driver needs a different clock (133MHz) on Intel devices
than on others (166MHz). Add a simple driver that provides this
information.
This driver can be expanded later as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sync the device tree files and device tree header files from upstream
Linux kernel, as of 2020-01-08. The commit synced to in the sunxi repo
98d25b0b266d Merge branch 'sunxi/dt-for-5.6' into sunxi/for-next
which is also part of next-20200108.
Changes brought in include:
- cleanup of pinmux node names
- addition of Security ID, MBUS, CSI, crypto engine, video codec,
pmu, and thermal sensor device nodes for both SoCs
- addition of deinterlacing engine device node on H3
- cleanup of RTC device node and addition of its clocks
- various board cleanups and improvements
- removal of pinmux node for GPIO lines
- cpufreq / DVFS
- HDMI output
- UART-based Bluetooth
- audio codec
- USB ports
- new boards
Most of the changes don't concern U-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
from https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git/
tag "ux500-armsoc-v5.6-2"
commit 224bf0fe7292 ("ARM: dts: ux500: samsung-golden: Add Bluetooth")
(queued for merge in Linux 5.6)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add clock manager driver for Agilex. Provides clock initialization
and get_rate functions.
agilex-clock.h is from Linux commit ID cd2e1ad12247.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Import fsl-imx-audmux.h from Linux as of v5.4-rc6. The header is
unchanged since v4.18.
That would make it easier to import DT files that depend on imx-audmux
definitions from the kernel tree.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Based on commit 980066e6d964 ("dt-bindings: phy: dp83867: Add documentation
for disabling clock output") of mainline linux kernel.
The clock output is generally only used for testing and development and not
used to daisy-chain PHYs. It's just a source of RF noise afterward.
Add a mux value for "off". I've added it as another enumeration to the
output property. In the actual PHY, the mux and the output enable are
independently controllable. However, it doesn't seem useful to be able
to describe the mux setting when the output is disabled.
Document that PHY's default setting will be left as is if the property
is omitted.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Device tree and binding alignment with kernel v5.4-rc4
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Device tree and binding alignment with kernel v5.3
and converted to SPDX.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add clk controller driver for RK3308 SOC.
This patch depends on Elaine's pll patch[0].
[0]http://patchwork.ozlabs.org/patch/1183718/
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The px30 contains 2 separate clock controllers, pmucru and cru.
Add drivers for them.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add headers needed by the upcoming px30 support, including two
new dt-binding headers taken from the Linux kernel.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This updates the i.MX8MQ device trees and, necessarily, also the
i.MX8MQ clock bindings. These are taken verbatim from from the
Linux kernel version v5.4-rc2, which three small changes which
were already part of the previous device tree:
* Keep the PSCI reserved memory range
* Keep the alias for ethernet, so that the MAC address can be set
* Keep the modified #include for the IOMUXC pins
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Acked-by: Peng Fan <peng.fan@nxp.com>
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEiQkHUH+J02LLC9InKPlOlyTyXBgFAl2zFisACgkQKPlOlyTy
XBgf9RAAkNwLjqUcBz3Ob1briRG5HF4D6bZCpjtkTIO8a2fanUHbSehh30TX8x2X
z0t/9Sd4OZwAeTxfQ/AlbbVdiB9IMgEb6lJ30Vr88MRNoPhABIQ8hw5xAzFi/6x9
88YolS/HQo6iR9rzSlaKjdIHhPTH5oQzRJ3JLqSwZzfUNy+zqINEhs3SYCnD2lyV
gTgiIT3Y5nKrhVHPUCy+jQG+wwWej2NFgwn71vR3/PSQJwxBuasg0qqOKD9hRtpC
XL6VErE7bf00elO8xjEObYrmB2FpffXJdkazS2HtRYNyKx0quaRNXJt7wqxEVP9L
M6SmL+S7zBFAetc/iyrlaakPvn7ImehSZkgLYaTPc3yzO+6bgq9tLfBERn/B/s5g
YyIzPGF66L96nuu0eVGCgSoUBjzBE8l2QTI8dho5xJxjWAUJOWSB0egqfFZzYVFu
4X37w6Z0j6uTK2oEl7KgJdc0JsZRsAJ8ZiqgOeNeMUTl2RnjGt0Oa7E24Va3n3hM
5vuEba9nPUFmdC5vlSd2RUK/dB587uKV93r5j54U62clpbiK+VMaRuRVX64ytZvB
B/0fKyCu+y7bxeZe4/X27jBUOk5yCuxbNI66m+cnnvfHqEmhz5PfDCEK1Dr29oqf
sCJLgTr7ahyuW4kEoL7KCOBEugPI85fp8/OlqC63M6/Kft0w5sA=
=6G/J
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-10-25' of git://git.denx.de/u-boot-mips
- bmips: add BCRM NAND support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs
- bmips: various small fixes
- mtmips: add new drivers for clock, reset-controller and pinctrl
- mtmips: add support for high speed UART
- mtmips: update/enhance drivers for SPI and ethernet
- mtmips: add support for MMC
This patch adds a clock driver for MediaTek MT7628/7688 SoC.
It provides clock gate control as well as getting clock frequency for
CPU/SYS/XTAL and some peripherals.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add dt clock header which can be included by dtses. And also use zynqmp-clk
compatible string.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In Linux meson-g12-common.dtsi was introduced as well as new g12b nodes
and headers, as dependencies of new meson-g12b-a311d-khadas-vim3.dts.
Copied from da0c9ea146cb ("Linux 5.4-rc2")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This follows the linux header rules to avoid conflict bitfields.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Add support for the reset controller that's used on the i.MX7D
and i.MX8MQ. This will be needed to be able to assert the PCIe
reset pins. Bindings taken from Linux, driver implementation
mostly taken from Linux and adjusted to U-Boot infrastructure.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for the power domain controller that's used on the
i.MX8MQ. This will be needed to be able to power on the PCIe
controller. Bindings taken from Linux, driver implementation
taken from the i.MX8 power domain controller and adjusted for
the i.MX8M SoC.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Sync kernel dts for i.MX6UL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add needed device-tree nodes to support PCIe 0
and SERDES on AM65x SoC. The nodes are kept
disabled by default.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>