Fix calls to dfu_write() and dfu_flush() to detect errors in the I/O
itself. This could happen due to problems with the storage medium, or
simply when trying to write a FAT/ext file that is larger than the buffer
dfu_mmc.c maintains for this purpose.
Signal the error by switching the DFU state/status. This will be picked
up by the DFU client when it sends the next DFU request. Note that errors
can't simply be returned from e.g. dnload_request_complete(), since that
function has no way to pass errors back to the DFU client; a call to
dnload_request_complete() simply means that a USB OUT completed.
This error state/status needs to be cleared when the next DFU client
connects. While there is a DFU_CLRSTATUS request, no DFU client seems to
send this. Hence, clear this when selecting the USB alternate setting on
the USB interface.
Finally, dfu.c relies on a call to dfu_flush() to clear up the internal
state of the write transaction. Now that errors in dfu_write() are
detected, dfu_flush() may no longer be called for every transaction.
Separate out the cleanup code into a new function, and call it whenever
dfu_write() fails, as well as from any call to dfu_flush().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
DFU read support appears to rely upon dfu->read_medium() updating the
passed-by-reference len parameter to indicate the remaining size
available for reading.
dfu_read_medium_mmc() never does this, and the implementation of
dfu_read_medium_nand() will only work if called just once; it hard-codes
the value to the total size of the NAND device irrespective of read
offset.
I believe that overloading dfu->read_medium() is confusing. As such,
this patch introduces a new function dfu->get_medium_size() which can
be used to explicitly find out the medium size, and nothing else.
dfu_read() is modified to use this function to set the initial value for
dfu->r_left, rather than attempting to use the side-effects of
dfu->read_medium() for this purpose.
Due to this change, dfu_read() must initially set dfu->b_left to 0, since
no data has been read.
dfu_read_buffer_fill() must also be modified not to adjust dfu->r_left
when simply copying data from dfu->i_buf_start to the upload request
buffer. r_left represents the amount of data left to be read from HW.
That value is not affected by the memcpy(), but only by calls to
dfu->read_medium().
After this change, I can read from either a 4MB or 1.5MB chunk of a 4MB
eMMC boot partion with CONFIG_SYS_DFU_DATA_BUF_SIZE==1MB. Without this
change, attempting to do that would result in DFU read returning no data
at all due to r_left never being set.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
It is redundant to use 'PFUZE100_PMIC' as the PMIC name because we already
know it is a PMIC.
Call it simply 'PFUZE100' instead.
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Messages to afleming@freescale.com now bounce, and should be
directed to my personal address at afleming@gmail.com
Signed-off-by: Andy Fleming <afleming@gmail.com>
if status register do never set MXC_CSPICTRL_TC, spi_xchg_single
endless loops. Add a timeout here to prevent endless hang.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Dirk Behme <dirk.behme@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This parameter should also be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
The SPI transaction delay is supposed to be measured from the end of one
transaction to the start of the next. The code does not work that way, so
fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
An incorrect message version is passed to the EC in some cases and the
parameters of one function are switched.
Fix these problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
It's usually a common pattern to free() the memory that we allocated.
Implement this here to stop leaking memory.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
If the MCI IP version >= 0x300, it supports hight speed mode
option, this patch enable it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The mode register is different between MCI IP version.
So, according to MCI IP version to set the mode register.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
To fix the clock divider calculation error when the controller
clock same as the operating frequency. This is known as bypass
mode. In this mode, the divider should be 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Implement SD driver for the S3C24xx family. This implementation
is currently only capable of using the PIO transfers, DMA is not
supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Seems like the controller doesn't support the flag. None of the hi-speed cards
I've tried could be read, while they successfully worked with the quirk enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.
Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
The Allwinner aka sunxi SoCs have one or more USB host controllers.
This adds a driver for their EHCI.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This enables the necessary clocks, in AHB0 and in PLL6_CFG. This is done
for sun7i only since I don't have access to any other sunxi platforms
with sata included.
The PHY setup is derived from the Alwinner releases and Linux, but is mostly
undocumented.
The Allwinner AHCI controller also requires some magic (and, again,
undocumented) DMA initialisation when starting a port. This is added under a
suitable ifdef.
This option is enabled for Cubieboard, Cubieboard2 and Cubietruck based on
contents of Linux DTS files, including SATA power pin config taken from the
DTS. All build tested, but runtime tested on Cubieboard2 and Cubietruck only.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Use CONFIG_SOC_KEYSTONE in common places instead of defining
a lot of "if def .. || if def " for different Keystone2 SoC types.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The Keystone SoCs use the same NAND driver as Davinci.
This patch adds opportunity to write Keystone U-boot image to NAND
device using appropriate RBL ECC layout. This is needed only if RBL
boots U-boot from NAND device and that's supposed that raw u-boot
partition is used only for writing image.
The main problem is that default Davinci ECC layout is different from
Keystone RBL layout. To read U-boot image the RBL needs that image was
written using RBL ECC layout.
The BBT table is written using default Davinci layout and has to
be updated using one. The BBT can be updated only while erasing
chip or by forced bad block assigning, so erase function has to
use native ecc layout in order to be able to write BBT correctly.
So if we're writing to NAND U-boot address we use RBL layout for
others we use default ECC layout.
Also remove definition for CONFIG_CMD_NAND_ECCLAYOUT as there is no
reasons to use ECC layout commands. It was added by mistake.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Add in an init function for the drivers/power framework so we can dump
and read the registers via i2c.
Cc: Łukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Tom Rini <trini@ti.com>
R8A7794 has the same sh-ether IP core as other SH/rmobile.
This patch adds support of R8A7794.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Some boards will have devices which are not in the device tree and do not
have platform data. They may be programnatically created, for example.
Add a hook which boards can use to bind those devices early in boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a debug message for when a device tree node has no driver. Also reword
the warning when a device fails to bind, which was misleading.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices (particularly bus devices) must track their children, knowing
when a new child is added so that it can be set up for communication on the
bus.
Add a child_pre_probe() method to provide this feature, and a corresponding
child_post_remove() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some device types can have child devices and want to store information
about them. For example a USB flash stick attached to a USB host
controller would likely use this space. The controller can hold
information about the USB state of each of its children.
The data is stored attached to the child device in the 'parent_priv'
member. It can be auto-allocated by dm when the child is probed. To
do this, add a per_child_auto_alloc_size value to the parent driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Devices can have childen that can be addressed by a simple index, the
sequence number or a device tree offset. Add functions to access a child
in each of these ways.
The index is typically used as a fallback when the sequence number is not
available. For example we may use a serial UART with sequence number 0 as
the console, but if no UART has sequence number 0, then we can fall back
to just using the first UART (index 0).
The device tree offset function is useful for buses, where they want to
locate one of their children. The device tree can be scanned to find the
offset of each child, and that offset can then find the device.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only root nodes in the device tree are scanned for devices.
But some devices can have children. For example a SPI bus may have
several children for each of its chip selects.
Add a function which scans subnodes and binds devices for each one. This
can be used for the root node scan also, so change it.
A device can call this function in its bind() or probe() methods to bind
its children.
Signed-off-by: Simon Glass <sjg@chromium.org>
Each device that was bound from a device tree has an node that caused it to
be bound. Add functions that find and return a device based on a device tree
offset.
Signed-off-by: Simon Glass <sjg@chromium.org>
In U-Boot it is pretty common to number devices from 0 and access them
on the command line using this numbering. While it may come to pass that
we will move away from this numbering, the possibility seems remote at
present.
Given that devices within a uclass will have an implied numbering, it
makes sense to build this into driver model as a core feature. The cost
is fairly small in terms of code and data space.
With each uclass having numbered devices we can ask for SPI port 0 or
serial port 1 and receive a single device.
Devices typically request a sequence number using aliases in the device
tree. These are resolved when the device is probed, to deal with conflicts.
Sequence numbers need not be sequential and holes are permitted.
At present there is no support for sequence numbers using static platform
data. It could easily be added to 'struct driver_info' if needed, but it
seems better to add features as we find a use for them, and the use of -1
to mean 'no sequence' makes the default value somewhat painful.
Signed-off-by: Simon Glass <sjg@chromium.org>
For sandbox we have a fallback console which is used very early in
U-Boot, before serial drivers are available. Rather than try to guess
when to switch to the real console, add a flag so we can be sure. This
makes sure that sandbox can always output a panic() message, for example,
and avoids silent failure (which is very annoying in sandbox).
Signed-off-by: Simon Glass <sjg@chromium.org>
Initialise devices marked 'pre-reloc' and make them available prior to
relocation. Note that this requires pre-reloc malloc() to be available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Driver model currently only operates after relocation is complete. In this
state U-Boot typically has a small amount of memory available. In adding
support for driver model prior to relocation we must try to use as little
memory as possible.
In addition, on some machines the memory has not be inited and/or the CPU
is not running at full speed or the data cache is off. These can reduce
execution performance, so the less initialisation that is done before
relocation the better.
An immediately-obvious improvement is to only initialise drivers which are
actually going to be used before relocation. On many boards the only such
driver is a serial UART, so this provides a very large potential benefit.
Allow drivers to mark themselves as 'pre-reloc' which means that they will
be initialised prior to relocation. This can be done either with a driver
flag or with a 'dm,pre-reloc' device tree property.
To support this, the various dm scanning function now take a 'pre_reloc_only'
parameter which indicates that only drivers marked pre-reloc should be
bound.
Signed-off-by: Simon Glass <sjg@chromium.org>
The root device should be probed just like any other device. The effect of
this is to mark the device as activated, so that it can be removed (along
with its children) if required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
There is no point in setting a structure's memory to NULL when it has
already been zeroed with memset().
Also, there is no need to create a stub function for stdio to call - if the
function is NULL it will not be called.
This is a clean-up, with no change in functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
enable the W#/Vpp signal to disable writing to the status
register on ST MICRON flashes like the N25Q128 thorugh
the new config option CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
add basic support for the pwm modul found on imx6.
Pieces of this code are based on linux code from drivers/pwm/pwm-imx.c
Commit "cd3de83f1476 Linux 3.16-rc4"
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The field wrtord_bg should add 2 clocks if on the fly chop is enabled,
according to DDR controller manual for DDR4.
Signed-off-by: York Sun <yorksun@freescale.com>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
Internal SRAM has been incresed from 8KB to 16KB for IFC cotroller ver 2.0.
Update the page offset calculation logic to support the same.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Even u-boot boots up, the pcie link may not setup correctly when
Freescale SOC acts as endpoint.
So change the link status from 'no link' to 'undetermined' to
reduce the confusion.
The link status can check from host side eventually.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
IFC controller v1.1.0 requires internal SRAM initialize by reading
NAND flash. Higher controller versions have provided "SRAM init" bit in
NCFGR register space.
update SRAM initialize logic to reflect the same.
Also print error message in case of Page read error.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The number of chip select used by IFC controller vary from one SoC to other.
For eg. P1010 has 4, T4240 has 8.
Update MAX_BANKS same as SoC defined
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
ls1021 is arm-core and supports qe too.
Move immap_qe.h into common directory for both arm and powerpc.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Some of the fm_port_to_index() callers did not check for -1 return value and
used -1 as an array index.
Signed-off-by: Marian Rotariu <marian.rotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In 73545f75b6 "ahci: wait longer for link" I increased the
timeout to 40ms based on the observed behaviour of a WD disk on a
Cubietruck. Since then Karsten Merker and myself have both
observed timeouts with HGST disks (Karsten on Cubietruck, me on
Cubieboard2). Increasing the timeout to ~175ms fixes this, so go
to 200ms for a bit of headroom.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Karsten Merker <merker@debian.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Just for type checking.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
The function still returns the same value.
The comment block is no longer necessary because our intention is
clear enough by using DIV_ROUND_CLOSEST() macro.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If CONFIG_OMAP1610 is defined, the code returning the fixed value (26)
is enabled. But this case is covered by the following code.
(CONFIG_SYS_NS16550_CLK + (gd->baudrate * (MODE_X_DIV / 2))) /
(MODE_X_DIV * gd->baudrate)
= (48000000 + (115200 * (16 / 2))) / (16 * 115200)
= 48921600 / 1843200
= 26
The "#ifdef CONFIG_OMAP1610" was added by commit 6f21347d more than
ten years ago. In those days, the divide-and-round was not used.
I guess that is why this weird code was added here.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Rishi Bhattacharya <rishi@ti.com>
upper_32_bits() and lower_32_bits() have been ported into linux/compat.h.
Start use them now in drivers/usb/host/xhci.h.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Add missing prototypes for global functions and
make local functions static.
cc: panto@antoniou-consulting.com
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
lists.c / root.c do not include their own header and they
could potentially implement a different function. Therefore
actually include the headers.
cc: sjg@chromium.org
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Simon Glass <sjg@chromium.org>
clang warns this check is silly; it is since s is
a local variable.
u-boot/drivers/mtd/cfi_flash.c:2363:13: warning: comparison of
array 's' not equal to a null pointer is always true
else if ((s != NULL) && (strcmp(s, "yes") == 0)) {
cc: Stefan Roese <sr@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Add support for the x-powers axp152 pmic which is found on most A10s boards
and enable it for the r7-tv-dongle board.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the x-powers axp209 pmic which is found on most A10, A13 and
A20 boards.
And enable AXP209 support for the Cubietruck and Cubieboard boards.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).
The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
If a bus busy is detected when intializing the driver,
toggle 9 times the scl pin. Therefore enable the test mode
of the controller, in which the scl, sda pins can be
controlled manually.
Tested on the siemens boards pxm2, rut and dxr2.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Lubomir Popov <lpopov@mm-sol.com>
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Vincent Stehlé <v-stehle@ti.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Newer AM437x silicon requires us to explicitly power up
the USB2 PHY. By implementing usb_phy_power() we can
achieve that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
IHS I2C master support was merely a hack in the osd driver.
Now it is a proper u-boot I2C framework driver, supporting the
v2.00 master features.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
get_sclk() was not defined in bfin_wdt.c, include the corresponding header.
Cc: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Vasili Galka <vvv444@gmail.com>
clang is tempted to inteprete such a condition as a assignment
as well. Since it isn't don't use double brackets.
cc: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
The directory arch/${ARCH}/cpu/${CPU} does not exist
in avr32, blackfin, microblaze, nios2, openrisc, sandbox, x86.
These architectures have only one CPU type.
Defining CPU should not be required for such architectures.
This commit allows cpu field (= the 3rd field of boards.cfg)
to be kept blank.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
There have been 3 versions of the sunxi_emac support patch during its
development. Somehow version 2 ended up in upstream u-boot where as
the u-boot-sunxi git repo got version 3.
This bumps the version in upstream u-boot to version 3 of the patch:
- Initialize MII clock earlier so mii access to allow independent use
- Name change from WEMAC to EMAC to match mainline kernel & chip manual
- Cosmetic code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The DMA code in sunxi_mmc.c is broken. mmc_trans_data_by_dma() allocates the
dma descriptors on the stack, and then exits while the dma transfer is in
progress, so the dma engine is reading stack memory which at that point may
be re-used. So far we've gotten away with this by luck, but recent u-boot
changes have shifted the stack start address by 16 bytes, which combined
with dma alignment now exposes this problem.
Since we end up just busy waiting for the dma engine anyway, this commit
fixes things by simply removing the dma code, resulting in smaller bug-free
code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
To add the DesignWare watchdog driver support. It required
information such as register base address and clock info from
configuration header file within include/configs folder.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
In current gpio_set_value() implementation, it always sets the gpio control bit
no matter the value argument is 0 or 1. Thus the GPIOs never set to low.
This patch fixes this bug.
The address bus is used as a mask on read/write operations, so that independent
software drivers can set their GPIO bits without affecting any other pins in a
single write operation. Thus we don't need a read-modify-write to update the
register.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Adding support to load and start the Layerscape Management Complex (MC)
firmware. First, the MC GCR register is set to 0 to reset all cores. MC
firmware and DPL images are copied from their location in NOR flash to
DDR. MC registers are updated with the location of these images.
Deasserting the reset bit of MC GCR register releases core 0 to run.
Core 1 will be released by MC firmware. Stop bits are not touched for
this step. U-boot waits for MC until it boots up. In case of a failure,
device tree is updated accordingly. The MC firmware image uses FIT format.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Since tegra_i2c_{read,write}'s debug() call dumps the chip address, dump
the address length (alen) too, so the address value can be correctly
interpreted.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
The Tegra I2C controller's TX FIFO contains 32-bit words. If the final
FIFO entry of a transaction contains fewer than 4 bytes, the driver
currently fills the unused FIFO bytes with uninitialized data. This can
be confusing when reading back the FIFO content for debugging purposes.
Solve this by explicitly initializing the variable containing FIFO data
before filling it (partially) with data. With this change,
send_recv_packets()'s loop's if (is_write) code mirrors the else (i.e.
read) branch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
I2C read transactions are typically implemented as follows:
START(write) address REPEATED_START(read) data... STOP
However, Tegra's I2C driver currently implements reads as follows:
START(write) address STOP START(read) data... STOP
This sequence confuses at least the AS3722 PMIC on the Jetson TK1 board,
leading to corrupted read data in some cases. Fix the driver to chain
the transactions together using repeated starts to solve this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
Almost all of ci_udc.c uses variable name "ep" for a struct usb_ep and
"ci_ep" for a struct ci_ep. This is nice and consistent, and helps people
know what type a variable is without searching for the declaration.
handle_ep_complete() doesn't do this, so fix it to be consistent.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A UDC's alloc_request method should zero out the newly allocated request.
Ensure the Atmel driver does so. This issue was found by code inspection,
following the investigation of an intermittent issue with ci_udc, which
was tracked down to failing to zero out allocated requests following some
of my changes. All other UDC drivers already zero out requests in one
way or another.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
struct ci_req is a purely software structure, and needs no specific
memory alignment. Hence, allocate it with calloc() rather than
memalign(). The use of memalign() was left-over from when struct ci_req
was going to hold the aligned bounce buffer, but this is now dynamically
allocated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
There's no need to store an array of QTD pointers in the controller.
Since the calculation is so simple, just have ci_get_qtd() perform it
at run-time, rather than pre-calculating everything.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
2 QTDs are allocated for each EP. The current allocation scheme aligns
the first QTD in each pair, but simply adds the struct size to calculate
the second QTD's address. This will result in a non-cache-aligned
addresss IF the system's ARCH_DMA_MINALIGN is not 32 bytes (i.e. the
size of struct ept_queue_item).
Similarly, the original ilist_ent_sz calculation aligned the value to
ARCH_DMA_MINALIGN but didn't take the USB HW's 32-byte alignment
requirement into account. This doesn't cause a practical issue unless
ARCH_DMA_MINALIGN < 32 (which I suspect is quite unlikely), but we may
as well fix the code to be explicit, so it's obviously completely
correct.
The new value of ILIST_ENT_SZ takes all alignment requirements into
account, so we can simplify ci_{flush,invalidate}_qtd() by simply using
that macro rather than calling roundup().
Similarly, the calculation of controller.items[i] can be simplified,
since each QTD is evenly spaced at its individual alignment requirement,
rather than each pair being aligned, and entries within the pair being
spaced apart only by structure size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This will allow functions other than ci_udc_probe() to make use of the
constants in a future change.
This in turn requires converting the const int variables to #defines,
since the initialization of one global const int can't depend on the
value of another const int; the compiler thinks it's non-constant if
that dependency exists.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Fix ci_ep_submit_next_request()'s ZLP transmission code to explicitly
call ci_get_qtd() to find the address of the other QTD to use. This
will allow us to correctly align each QTD individually in the future,
which may involve leaving a gap between the QTDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ci_udc_probe() initializes a pair of QHs and QTDs for each EP. After
each pair has been initialized, the pair is cache-flushed. The
conversion from QH/QTD index [0..2*NUM_END_POINTS) to EP index
[0..NUM_ENDPOINTS] is incorrect; it simply subtracts 1 (which yields
the QH/QTD index of the first entry in the pair) rather than dividing
by two (which scales the range). Fix this.
On my system, this avoids cache debug prints due to requests to flush
unaligned ranges. This is caused because the flush calls happen before
the items[] array entries are initialized for all but EP0.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add LAN9500A product ID (0x9e00) in order to support LAN9500A based dongles.
Tested on cm_t335.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Acked-by: Marek Vasut <marex@denx.de>
cb_getvar tries to prevent overflowing the response buffer
by using strncat. But strncat takes the number of data bytes
copied as a limit not the total buffer length so it can still
overflow. Pass the correct value instead.
cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
cc: Rob Herring <robh@kernel.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Because of the brackets the & and && is evaluated before
the comparison. This is likely not the intention. Change
it to test the first and second condition to both be true.
cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
since ALLOC_CACHE_ALIGN_BUFFER defines a pointer and not a
buffer, the memset with sizeof(rqt) likely does something else
then intended. Since there is a memcpy directly after it with
the full size, drop the memset completely.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Since the struct fsg_common is calloced, reset it completely
with zero's when reused. While at it, make checkpatch happy.
cc: Lukasz Majewski <l.majewski@samsung.com>
cc: Piotr Wilczek <p.wilczek@samsung.com>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Initialization of r8a66597 info structure is not enough.
Because initilization was used size of pointer.
This fixes that use size of r8a6659 info structure.
Signed-off-by: Yasuhisa Umano <yasuhisa.umano.zc@renesas.com>
This driver is processed as two USB hub despite one.
The number of root hub is defined in R8A66597_MAX_ROOT_HUB.
This fixes that register is accessed by using the definition
of R8A66597_MAX_ROOT_HUB.
Signed-off-by: Yasuhisa Umano <yasuhisa.umano.zc@renesas.com>
For plain array const can be either before or after
the type definition. Adding both is simply redundand.
Remove the later one.
cc: marex@denx.de
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
ci_udc.c's usb_gadget_unregister_driver() doesn't call driver->unbind()
unlike other USB gadget drivers. Fix it to do this.
Without this, when ether.c's CDC Ethernet device is torn down,
eth_unbind() is never called, so dev->gadget is never set to NULL.
For some reason, usb_eth_halt() is called both at the end of the first
use of the Ethernet device, and prior to any subsequent use. Since
dev->gadget is never cleared, all calls to usb_eth_halt() attempt to
stop, disconnect, and clean up the device, resulting in double cleanup,
which hangs U-Boot on my Tegra device at least.
ci_udc allocates its own singleton EP0 request object, and cleans it up
during usb_gadget_unregister_driver(). This appears necessary when using
the USB gadget framework in U-Boot, since that does not allocate/free
the EP0 request. However, the CDC Ethernet driver *does* allocate and
free its own EP0 requests. Consequently, we must protect
ci_ep_free_request() against double-freeing the request.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Since p->bus is unsigned checking for negative values
is optimized away. Since bus is already used as an argument
use tmp. While at it, don't declare variables in the middle
of a function.
cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
SPI recieve and transfer code in exynos_spi driver has a logical bug.
We read data in a variable which can hold an integer. Then we assign
this integer 32 bit value to another variable which has data type uchar.
Latter represents a unit of our recieve buffer. Everytime when we write
a value to our recieve buffer we step ahead by 4 units when actually we
wrote to one unit. This results in the loss of 3 bytes out of every 4
bytes recieved. This patch intends to fix this bug.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In a very few cases we need to adjust the driver model root device, such as
when setting it up at initialisation. Add a macro to make this easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want 'N0' and 'n0' to mean the same thing, so ensure that case is not
considered when naming GPIO banks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
The function tps65090_init checks the i2c bus of p->bus. However
the pointer p is not intialiased at this point. Check the local
variable bus instead.
cc: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Simon Glass <sjg@chromium.org>
commit 18b06652cd "tools: include u-boot version of sha256.h"
unconditionally forced the sha256.h from u-boot to be used
for tools instead of the host version. This is fragile though
as it will also include the host version. Therefore move it
to include/u-boot to join u-boot/md5.h etc which were renamed
for the same reason.
cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
To support dcache, we need flush DMA descriptor buffer before enable lcd
DMA.
Also we need call lcd_set_flush_dcache(1) to make lcd driver flush the
lcd buffer if there is any change.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add to code to flush the dcache after we writing in DMA buffer.
Also we need invalidate the dcache before we check the status in the
DMA buffer.
Tested in SAMA5D3x-EK with gmac0. Tftp download speed shows in below:
Disable DCache: 1.1 MiB/s
Enable DCache: 1.6 MiB/s
Increase speed with about 40%.
The code should have no impact with the boards which are not
enable_dcache().
Tested in AT91SAM9M10G45EK.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This also renames the CONFIG_SYS_MACB_xx defines. They are used just local and
therefore don't need the CONFIG_SYS_ prefix.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Josh Wu <josh.wu@atmel.com>
Cleanup to balance malloc/free calls.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Rather than just returning -1 everywhere, try to return something
meaningful from mmc_select_hwpart(). Note that most other MMC functions
don't do this, including functions called from mmc_select_hwpart(), so
I'm not sure how effective this will be. Still, it's one less place with
hard-coded -1.
Suggested-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Most of the warnings seem to be related to using 'int' for size_t. Change
this and fix up the remaining warnings and problems. For bootm, the warning
was masked by others, and there is an actual bug in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Patch (SHA1: bd694244db)
dfu: Introduction of the "dfu_hash_algo" env variable for checksum method
setting
already introduced more generic handling of the crc32 calculation.
Up till now the CRC32 of received data was calculated unconditionally.
This patch changes this and from now - by default the crc32 is NOT
calculated anymore.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Sometimes, a zero-length packet is required at the end of an IN
transaction so that the host knows the device is done sending data.
Enhance ci_udc to send a zlp when necessary. See the comments for
more details.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
usb_gadget_unregister_driver() is called to tear down the USB device mode
stack. Fix the driver to stop the USB HW (which causes any attached host
to notice the disappearance of the device), and free all allocations
(which obviously prevents memory leaks).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ci_ep_alloc_request() avoids allocating multiple request objects for ep0
by keeping a record of the first req allocated for ep0, and always
returning that instead of allocating a new req. However, if this req is
ever freed, the record of the previous allocation is not cleared, so
ci_ep_alloc_request() will keep returning this stale pointer. Fix
ci_ep_free_request() to clear the record of the previous allocation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
ci_pullup()'s !is_on path contains a cut/paste copy of udc_disconnect().
Remove the duplication by simply calling udc_disconnect() instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
'r' of rESR_RTLF is a mistake of E.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
