Switch to using hardware leveling for certain parameters on the EMIF
rather than using precalculated values. Doing this also means we have a
common place now between am437x and am335x for setting
emif_sdram_ref_ctrl with a value for the correct delay length.
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The code intends for the CM_DLL_READYST to be set, but
actually polls till any bit is set since the logical
AND is used instead of the bitwise one is used. Fix it.
cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
We have two contexts for booting these platforms. One is SPL which is
roughly: reset, cpu_init_crit, lowlevel_init, s_init, sdram_init, _main,
board_init_f from SPL, ... then U-Boot loads. The other is a
memory-mapped XIP case (NOR or QSPI) where we do not run an SPL. In
this case we go, roughly: reset, cpu_init_crit, lowlevel_init, s_init,
_main, regular board_init_f.
In the first case s_init will set a valid gd and then be able to call
sdram_init which in many cases will need i2c (which needs a valid gd for
gd->cur_i2c_bus). In this second case we must (and are able to and
should) defer sdram_init() into dram_init() called by board_init_f as gd
will have been set in _main and cleared in board_init_f.
Signed-off-by: Tom Rini <trini@ti.com>
In the case of SPL or NOR_BOOT (no SPL involved) we need to include
certain code in the build. Use !CONFIG_SKIP_LOWLEVEL_INIT rather than
CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to
make supporting XIP QSPI boot clearer in the code.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
The bit DDR3_RST_DEF_VAL inside CTRL_DDR_IO represents the default value
of the ddr reset value for DDR3 before the EMIF takes over. We must have
this bit set high so that on exit from DeepSleep0 within the kernel the
reset line has the proper value.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Fix warnings about vtp things in emif4.c, adapt AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.
This is derived from OMAP4 boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on. When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.
We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
The AM33xx emif4/ddr support closely matches what is need to support
TI814x except that TI814x has two EMIF instances. Refactor all the
emif4 helper calls and the config_ddr() init function to use an
additional instance number argument.
Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Move the hardcoded ddr2/ddr3 settings for the ti boards to board code,
so other boards can use different types/timings.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make apply with rtc32k_enable() in the file]
Signed-off-by: Tom Rini <trini@ti.com>
In order to support DDR3 as well as DDR2, we need to perform the same
init sequence, but with different values. So change config_ddr() to
toggle setting pointers/etc for what DDR2 wants, and then calling.
Signed-off-by: Tom Rini <trini@ti.com>
The ddr_regs struct was incorrectly offset after the dt0wiratio0 entry.
Correct this by documenting a missing register that will be used at some
point in the future (when write leveling is supported). Further, the
cmdNcs{force,delay} fields are undocumented and we have been setting
them to zero, remove. Next, setting of the
'DATAn_REG_PHY_USE_RANK0_DELAYS field belongs with the rest of the
ddr_data entries, so program it there. Finally, comment on how we are
configuring the DATA1 registers that correspond to the DATA0 (dt0)
registers defined in the struct.
Signed-off-by: Tom Rini <trini@ti.com>
The various ratio1 fields are not documented in any of the documentation
I can find. Removing these and testing has yielded success, so remove
the code that sets them and move their locations into the reserved
fields.
Signed-off-by: Tom Rini <trini@ti.com>
This function sets a number of related registers to the same value (the
registers in question all have the same field descriptions and are
related in operation). Rather than defining a struct and setting the
value repeatedly, just pass in the value.
Signed-off-by: Tom Rini <trini@ti.com>
Rather than defining our own structs to note what to use when
programming the EMIF and related re-use the emif_regs struct.
Signed-off-by: Tom Rini <trini@ti.com>
A number of memory initalization functions were int and always returned
0. Further it's not feasible to be doing error checking here, so simply
turn them into void functions.
Signed-off-by: Tom Rini <trini@ti.com>
- Remove the call to set ddrctrl->ddrioctrl as it's all zeros.
- Comment what we're really setting in ddrctrl->ddrckectrl which is that
we're operating in the normal mode where EMIF/PHY clock is controlled
by the PHY.
Signed-off-by: Tom Rini <trini@ti.com>
Depending on if we have DDR2 or DDR3 on the board we will need to call
ddr_pll_config with a different value. This call can be delayed
slightly to the point where we know which type of memory we have.
Signed-off-by: Tom Rini <trini@ti.com>
We need to pass in the type of memory that is connected to the board.
The only reliable way to do this is to know what type of board we are
running on (which later will be knowable in s_init()). For now, pass in
the value of DDR2.
Signed-off-by: Tom Rini <trini@ti.com>
Rework the EMIF4/DDR code slightly to setup the structs that
config_cmd_ctrl and config_ddr_data take to be setup at compile time and
mark them as const. This lets us simplify the calling path slightly as
well as making it easier to deal with DDR3.
Signed-off-by: Tom Rini <trini@ti.com>
With the previous bugfix we now don't need to set two different REF_CTRL
values and instead set the final value.
Signed-off-by: Tom Rini <trini@ti.com>
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This patch adds AM33xx emif/ddr support along with board specific
defines.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
