This patch adds hardware ECC support to the NDFC driver. It also
changes the register access from using the "simple" in32/out32
functions to the in_be32/out_be32 functions, which make sure
that the access is correctly synced. This is the only recommended
access to SoC registers in the current Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the nand_ecc code to the latest Linux version.
The main reason for this is the more compact code. This makes
it possible to include the ECC code into the NAND bootloader
image (NAND_SPL) for PPC4xx.
Signed-off-by: Stefan Roese <sr@denx.de>
Enable redundant environment, add a MTD partition for it; also add env.
variable command for passing MTD partitions to the kernel command line.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
Allow passing longer command line to the kernel - useful especially
for passing MTD partition layout.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
Change EEPROM configuration according to the datasheet: "The 24C01A and 24C02A
have a page write capability of two bytes", and "This device offers fast (1ms)
byte write". Add 3ms of extra delay.
Signed-off-by: Piotr Kruszynski <ppk@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
After being reset in mpc5xxx_fec_init_phy(), PHY goes into FX mode, in which
networking does not function. This commit switches PHY to TX mode by clearing
the FX_SEL bit of Mode Control Register. It also reverses commit
008861a2f3, i.e., a temporary workaround.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
Both CFG_PCISPEED_66 and CFG_IPBSPEED_133 are misnamed, as defining
them does not cause PCI or IPB clocks to run at the specified speed.
Instead, they configure divisors used to calculate said clocks. This
patch renames the defines according to their real function.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
Acked-by: Bartlomiej Sieka <tur@semihalf.com>
As pointed out by Bruce Adler <bruce.adler@acm.org> this patch
fixes a small bug in the 405EZ OCM initialization. Thanks for
spotting.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch updates the Acadia (405EZ) support for the new 1.1 board
revision. It also adds support for NAND FLASH via the 4xx NDFC.
Please note that the jumper J7 must be in position 2-3 for this
NAND support. Position 1-2 is for NAND booting only. NAND booting
support will follow later.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for 405 PPC's to the 4xx NAND driver
ndfc.c. This is in preparation for the new AMCC 405EZ.
Signed-off-by: Stefan Roese <sr@denx.de>
For all practical u-boot purposes, TSECs don't differ throughout the
mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Because the Sequoia board does not boot with an EBC faster than 66MHz,
the clock divider are changed after the initial boot process.
This allows for maximum clocking speeds to be achieved on newer boards.
Sequoia boards with 666.66 MHz processors require that the EBC divider
be set to 3 in order to start the initial boot process at a slower EBC
speed. After the initial boot process, the divider can be set back to 2,
which will cause the boards to run at 83.333MHz. This is backward
compatible with boards with 533.33 MHz processors, as these boards will
already be set with an EBC divider of 2.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Bridge, ICH-5, ICH-6 and ICH-7.
Implementation:
1. Code is divided in to two files. All functions, which are
controller specific are kept in "drivers/ata_piix.c" file and
functions, which are not controller specific, are kept in
"common/cmd_sata.c" file.
2. Reading and Writing from the S-ATA drive is done using PIO method.
3. Driver can be configured for 48-bit addressing by defining macro
CONFIG_LBA48, if this macro is not defined driver uses the 28-bit
addressing.
4. S-ATA read function is hooked to the File system, commands like
ext2ls and ext2load file can be used. This has been tested.
5. U-Boot command "SATA_init" is added, which initializes the S-ATA
controller and identifies the S-ATA drives connected to it.
6. U-Boot command "sata" is added, which is used to read/write, print
partition table and get info about the drives present. This I have
implemented in same way as "ide" command is implemented in U-Boot.
7. This driver is for S-ATA in native mode.
8. This driver does not support the Native command queuing and
Hot-plugging.
Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
Hi,
There is a bug in the code of clearing the bss section for processor
i386.(File: cpu/i386/start.S)
In the code, bss_start addr (starting addr of bss section) is put into
the register %eax, but the code which clears the bss section refers to
the addr pointed by %edi.
This patch fixes this bug by putting bss_start into %edi register.
Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
Search the exception table with linear algorithm instead of
bisecting algorithm.
Because the exception table might be unsorted.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The attached patch fixes the compile of the JSE board in the
denx git as of 14 may 2007. It is an extremely simple patch,
it just adds the missing define of CFG_SYSTEMACE_WIDTH.
Fix to compile JSE against 20070514 git of u-boot
