Commit graph

142 commits

Author SHA1 Message Date
Grygorii Strashko
7da4fb9235 arm: ti: dra7: move BOOTP_DNS2 and PHY_TI in defconfig
Move BOOTP_DNS2 and PHY_TI from dra7xx_evm.h to
dra7xx_evm_defconfig.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-12-13 13:01:54 -05:00
Miquel Raynal
88718be300 mtd: rename CONFIG_NAND -> CONFIG_MTD_RAW_NAND
Add more clarity by changing the Kconfig entry name.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
2019-12-03 23:04:10 -05:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Tom Rini
cb6617a77f defconfigs: Migrate CONFIG_SYS_REDUNDAND_ENVIRONMENT
Move this symbol to Kconfig.  As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-12 11:08:00 -05:00
Hannes Schmelzer
1ee774d209 Convert CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_SPI_U_BOOT_OFFS

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25 20:59:00 -04:00
Sam Protsenko
adc097e133 env: ti: boot: Use ttyS2 instead of ttyO2
ttyO2 console enables legacy CONFIG_SERIAL_OMAP driver in kernel.
Nowadays it's preferred to use the generic CONFIG_SERIAL_8250_OMAP
driver, which being enabled via ttyS2 console. Both drivers are enabled
in multi_v7_defconfig and in omap2plus_defconfig, for compatibility
reasons. Let's switch to ttyS2 console, to be sure that standard 8250
serial driver is used.

Similar behavior can be also achieved by enabling
CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP option in kernel, but it's better not
to rely on that, as it can be disabled or removed after transitional
period.

Right now on DRA7/AM57x platforms the 8250-omap driver is being probed
first, and omap-serial driver is only probed if the first one failed.
It can be seen from uart3 definition in arch/arm/boot/dts/dra7-l4.dtsi:

    compatible = "ti,dra742-uart", "ti,omap4-uart";

So the kernel already uses 8250 driver. This change basically allows
kernel developers to throw away the omap-serial driver and associated
compatibility options. Similar discussions [1,2] have started several
years ago, so it should be safe to do that now.

[1] https://patchwork.kernel.org/patch/6198471/
[2] http://processors.wiki.ti.com/index.php/Sitara_Linux_UART_-_Switching_to_8250_Driver

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
[trini: Update omap5_uevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-07-27 13:36:54 -04:00
Markus Klotzbuecher
a9221f3ebd at91, omap2plus: configs: migrate CONFIG_ENV_ to defconfigs
Enable the extended ENV options for AT91 and OMAP2PLUS in order to be
able to use CONFIG_ENV_UBI_* on these architectures.

As this change also makes the configs ENV_SIZE, ENV_SECT_SIZE,
ENV_OFFSET visible to AT91 and OMAP2PLUS, migrate users of these to
KConfig.

This migration was run using an extended moveconfig.py which evaluates
expressions such as "(512 << 10)". See patch ("moveconfig: expand
simple expressions").

All modified boards were built with SOURCE_DATE_EPOCH=0 before and
after the change and successfully confirmed that the identical binary
is generated (the only exception was igep00x0, which does not define
CONFIG_ENV_IS_IN_UBI in the original board header. Once that is
defined, the test passes too).

hs: rebased patch to:
  68b90e57bc: "configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT"

Signed-off-by: Markus Klotzbuecher <markus.klotzbuecher@kistler.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Tom Rini <trini@konsulko.com>
2019-07-09 07:00:21 +02:00
Alex Kiernan
623de3f086 Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig
This converts the following to Kconfig:
   CONFIG_SUPPORT_EMMC_BOOT

As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:

  xilinx_zynqmp_zc1275_revB
  xilinx_zynqmp_zc1751_xm018_dc4
  xilinx_zynqmp_zc1751_xm019_dc5
  xilinx_zynqmp_zcu100_revC
  xilinx_zynqmp_zcu102_rev1_0
  xilinx_zynqmp_zcu102_revA
  xilinx_zynqmp_zcu102_revB
  xilinx_zynqmp_zcu104_revA
  xilinx_zynqmp_zcu104_revC
  xilinx_zynqmp_zcu106_revA
  xilinx_zynqmp_zcu111_revA

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-05-04 13:04:12 -04:00
Vignesh Raghavendra
61ae9782ef spi: ti_qspi: Drop non DM code
Now that all boards using TI QSPI have moved to DM and DT, drop non DM
code completely.

Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[jagan: update MIGRATION.txt, rebase config_whitelist.txt]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-17 17:43:19 +05:30
Faiz Abbas
097fd51b7a configs: ti_omap5_common: Add NAND environment settings
Now that NAND is supported on DRA71x include various NAND environment
settings

Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-04-12 08:05:50 -04:00
Patrick Delaunay
abe66b1b5d Convert CONFIG_ENV_SPI_* to Kconfig
This converts the following to Kconfig:
  CONFIG_ENV_SPI_BUS
  CONFIG_ENV_SPI_CS
  CONFIG_ENV_SPI_MAX_HZ
  CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:59 -04:00
Patrick Delaunay
14453fbfad Convert CONFIG_SF_DEFAULT_* to Kconfig
This converts the following to Kconfig:
  CONFIG_SF_DEFAULT_BUS
  CONFIG_SF_DEFAULT_CS
  CONFIG_SF_DEFAULT_MODE
  CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:53 -04:00
Andrew F. Davis
6536ca4d66 spl: Kconfig: Drop the _SUPPORT postfix from SPL_DFU
The symbol CONFIG_SPL_DFU_SUPPORT in SPL build has the same
meaning as CONFIG_DFU in regular U-Boot. Drop the _SUPPORT
to allow for cleaner use in code.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
2019-01-26 08:13:54 -05:00
Adam Ford
2fe88d4522 Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig
This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-10-19 19:19:50 -04:00
Tuomas Tynkkynen
1bc93b50e8 ata: Drop CONFIG_SYS_SCSI_MAX_* from boards using DM_SCSI
These options are not used or necessary when device model is being used
for SCSI. Just drop them.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
2018-09-25 21:49:18 -04:00
Adam Ford
d7869b2183 Convert CONFIG_MII et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-17 13:03:54 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Sam Protsenko
c90a760ffd arm: ti: boot: Extract PARTS_DEFAULT to boot.h
Eliminate code duplication: the same PARTS_DEFAULT was defined in
am57xx_evm.h and in dra7xx_evm.h. Extract it to environment/boot.h and
use in all OMAP5-based boards.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2018-05-08 18:50:22 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Marek Vasut
555004381e spl: spi: Move CONFIG_SPL_SPI_LOAD to Kconfig
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
2018-04-11 13:22:00 -04:00
Alex Kiernan
f02b8d1761 Migrate CONFIG_DRIVER_TI_CPSW to Kconfig
This converts CONFIG_DRIVER_TI_CPSW to Kconfig

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-08 23:00:58 -04:00
Adam Ford
d021e94210 Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTP_BOOTPATH
   CONFIG_BOOTP_DNS
   CONFIG_BOOTP_GATEWAY
   CONFIG_BOOTP_HOSTNAME
   CONFIG_BOOTP_PXE
   CONFIG_BOOTP_SUBNETMASK
   CONFIG_CMDLINE_EDITING
   CONFIG_AUTO_COMPLETE
   CONFIG_SYS_LONGHELP
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-23 21:41:49 -05:00
Kishon Vijay Abraham I
6a27333ba3 ARM: OMAP5/DRA7: Enable iodelay recalibration to be done from uboot
Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.

The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-02-19 16:58:55 +09:00
Adam Ford
b9b500b0f9 Convert CONFIG_OMAP_USB_PHY to Kconfig
This converts the following to Kconfig:
   CONFIG_OMAP_USB_PHY

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-01-22 16:43:30 -05:00
Tuomas Tynkkynen
b82e667f79 ata: Migrate CONFIG_LIBATA to Kconfig
This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12 18:16:05 -05:00
Tuomas Tynkkynen
9fd95ef0d3 ata: Migrate CONFIG_SCSI_AHCI to Kconfig
And use 'imply' liberally.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12 18:13:19 -05:00
Praneeth Bajjuri
65d87d6cfc dra7x: fastboot: Increase recovery partition size
As per current android recommendation
https://source.android.com/devices/architecture/kernel/modular-kernels

1. Android recovery mode should contain both SOC and ODM
kernel modules in the recovery partition.

2. If a kernel module is required both in recovery and normal boot
mode,  the module has to be located in recovery and vendor
partition seperately.

3. Kernel modules used in recovery mode should be independent
of vendor and odm partition

4. Recovery image should contain atleast
storage, display, keypad, battery and pmic modules.

Due to these requirements, recovery image size has increased
to >10MB.

This patch is to increase recovery partition size for TI devices
so that we dont see such flashing error

log:
sending 'recovery' (12560 KB)...
OKAY [  0.436s]
writing 'recovery'...
FAILED (remote: too large for partition)
finished. total time: 0.458s

Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2017-11-20 20:18:37 -05:00
Tom Rini
43ede0bca7 Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.

Tested-by: Adam Ford <aford173@gmail.com>  #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-11-05 11:21:35 -05:00
Adam Ford
0a9ef45158 Convert CONFIG_NAND_OMAP_GPMC et al and CONFIG_NAND_MXC to Kconfig
This converts the following to Kconfig:
   CONFIG_NAND_MXC
   CONFIG_NAND_OMAP_GPMC
   CONFIG_NAND_OMAP_GPMC_PREFETCH
   CONFIG_NAND_OMAP_ELM
   CONFIG_SPL_NAND_AM33XX_BCH
   CONFIG_SPL_NAND_SIMPLE
   CONFIG_SYS_NAND_BUSWIDTH_16BIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
        add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-10-20 16:44:07 -04:00
Vishal Mahaveer
3f3607ded4 arm: dra7xx: Add vendor partition to Android GPT table for eMMC
Add vendor partition to Android GPT table for eMMC.

A Vendor image contains SoC-specific code and configuration.

Prior to Android 8.0, the vendor partition was optional ;
files belonging to these images were placed in boot.img or system.img
with symlinks (such as /vendor >/system/vendor ) when absent.

Android 8.0 makes the vendor partition mandatory

The goal is to modularize Android partitions with standard interface between
the Android Platform (on system.img ) and vendor-provided code(on vendor.img).

This standard interface enables the Android Platform to be updated
without affecting the SoC partitions. This makes it possible to upgrade a
device system.img from Android 8.0 to Android P while other images (such as
vendor.img) remain at Android 8.0. This modularity enables timely
Android platform upgrades (such as monthly security updates )
without requiring SoC/ODM partners to update SoC- and device-specific code.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-10-16 09:43:34 -04:00
Maxime Ripard
47738acced cmd: Move CONFIG_RANDOM_UUID to Kconfig
CONFIG_RANDOM_UUID is used by the GPT command to generate random UUID when
none are provided.

Move that option to Kconfig.

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:05 +02:00
Sam Protsenko
a0b0ff0ae6 arm: dra7xx: Fix Linux boot from eMMC
Right now on OMAP5-based boards we have only one partition defined for
Linux boot, which is rootfs. That doesn't work with bootpart=1:2 (that
is defined in include/environment/ti/boot.h). To fix Linux boot we may
either:

 1. Change bootpart to be 1:1
 2. Or add preceding partition, so that rootfs is actually 1:2

Second choice seems more reasonable, as DFU is already using similar
partition table and can rely on bootpart to be 1:2.

This patch adds "bootloader" partition. So now eMMC layout for Linux
boot looks like this:

offset               content                 size          partition
(KiB)                                        (KiB)
Reviewed-by: Tom Rini <trini@konsulko.com>

=======================================================================

0       +--------------------------------+
        | MBR/GPT header                 |   128           -
128     +--------------------------------+
        | MLO                            |   256           -
384     +--------------------------------+
        | u-boot.img                     |   1792          bootloader
2176    +--------------------------------+
        | //////////// hole //////////// |   256           -
2432    +--------------------------------+
        | U-Boot environment             |   128           -
2560    +--------------------------------+
        | U-Boot environment (redundant) |   128           -
2688    +--------------------------------+
        | rootfs                         |   remaining     rootfs
end     +--------------------------------+

=======================================================================

Guard hole appears because U-Boot environment offset was calculated for
Android partition table, which has two additional partitions in place of
that hole ("environment" and "misc" partitions).

This patch also changes rootfs offset from 2 MiB further to 2688 KiB,
so that there won't be any collisions with U-Boot environment when we
flash rootfs.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
2017-09-29 14:07:58 -04:00
Tom Rini
48f6232e58 Kconfig: Migrate all of cmd/fastboot/Kconfig to defconfigs
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's
  not strictly part of fastboot.
- Add some defaults for the fastboot buffer location and size
- Migrate all options listed in cmd/fastboot/Kconfig
- Cleanup the README

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-01 16:18:21 -04:00
Adam Ford
ebb3e43de4 Convert CONFIG_OMAP3_SPI to Kconfig
This converts the following to Kconfig:
   CONFIG_OMAP3_SPI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Minor comment tweaks]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-13 15:17:10 -04:00
Simon Glass
3a91a25376 Convert CONFIG_CMD_SPL_WRITE_SIZE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_SPL_WRITE_SIZE

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:58 -04:00
Simon Glass
203dc1b3a8 Convert CONFIG_CMD_SPL_NAND_OFS to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_SPL_NAND_OFS

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:58 -04:00
Tom Rini
1989374b21 configs: Finish migration of PHY_GIGE
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-08 17:02:31 -04:00
Alexandru Gagniuc
3146f0c017 Move PHYLIB to Kconfig
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:22:28 -05:00
Bin Meng
2931342874 configs: Remove CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS in all boards
Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
2017-07-28 23:34:23 +02:00
Simon Glass
91c868fe7c Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_SPI_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-25 21:31:03 -04:00
Simon Glass
85fc970d74 Convert CONFIG_ENV_IS_IN_FLASH to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-25 21:20:02 -04:00
Simon Glass
2be296538e Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_MMC
   CONFIG_ENV_IS_IN_NAND
   CONFIG_ENV_IS_IN_UBI
   CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

   ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates.  This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-07-25 21:08:01 -04:00
Simon Glass
fedb428c5b Convert CONFIG_SCSI to Kconfig
This converts the following to Kconfig:
   CONFIG_SCSI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Semen Protsenko
ebeda0b117 arm: dra7: Increase "bootloader" partition size
Increase the size of u-boot.img, so that it conforms with new DFU
configuration (see commit [1]).

[1] 7a53a1a811 ARM: ti: Update layout for MMC and eMMC (env and dfu)

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-06-12 08:38:47 -04:00
Jean-Jacques Hiblot
7a53a1a811 ARM: ti: Update layout for MMC and eMMC (env and dfu)
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
     (>750KB). We need to increase it. eMMC uses a much bigger area (2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region
      "spl-os-image.raw".
both: region "spl-os-image.raw" is quite small and can't handle android
      kernels

Fixing this requires growing some regions and moving others.
Care has been taken to leave some room for further growth of
"spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the
region is not free space that can be used to grow "u-boot.img.raw".
The MLO region is 0x100 sectors wide but the 0x100 are unused in case the
MLO comes too overflow this areas.
The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
2017-06-05 14:13:10 -04:00
Simon Glass
a1dc980d88 Convert CONFIG_CMD_EEPROM et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_EEPROM
   CONFIG_CMD_EEPROM_LAYOUT
   CONFIG_EEPROM_LAYOUT_HELP_STRING

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-05-22 09:33:49 -04:00
Uri Mashiach
67566ab66b arm: dra7xx: move CONFIG_DRA7XX to Kconfig
The symbol CONFIG_DRA7XX is needed for Kconfig conditions.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-05-08 11:38:35 -04:00
Lokesh Vutla
0a3f407a7f configs: dra7xx_evm: Enable SPL_DM
Enable SPL_DM on all DRA7 based platforms.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-03-21 07:15:57 -04:00
Roger Quadros
66e04fb503 ARM: Use Kconfig for board EEPROM's I2C bus and chip address
In stead of defining the board EEPROM address in the board headers
let's define them in the board config files and make them
configurable by Kconfig.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-03-20 17:57:15 -04:00
Philipp Tomsich
f40574e2d7 Kconfig: Migrate CONFIG_BAUDRATE
Move this in to Kconfig with a default of 115200.

Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-19 14:48:37 -04:00