Commit graph

255 commits

Author SHA1 Message Date
Scott Wood
be33b046b5 Remove legacy NAND and disk on chip code.
Legacy NAND had been scheduled for removal.  Any boards that use this
were already not building in the previous release due to an #error.

The disk on chip code in common/cmd_doc.c relies on legacy NAND,
and it has also been removed.  There is newer disk on chip code
in drivers/mtd/nand; someone with access to hardware and sufficient
time and motivation can try to get that working, but for now disk
on chip is not supported.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 19:07:47 -05:00
Stefan Roese
fbdaafaee7 nand: Change NAND_MAX_OOBSIZE to 218 as needed for some 4k page devices
This is needed for the MPC512x NAND driver (fsl_nfc_nand.c) which already
defines such a 4k plus 218 bytes ECC layout.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-07-16 17:52:03 -05:00
Wolfgang Denk
8e5e9b940c Coding style cleanup; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-07-07 22:35:02 +02:00
Stefan Roese
8d2effea23 mtd: Update MTD infrastructure to support 64bit device size
This patch brings the U-Boot MTD infrastructure in sync with the current
Linux MTD version (2.6.30-rc3). Biggest change is the 64bit device size
support and a resync of the mtdpart.c file which has seen multiple fixes
meanwhile.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kyungmin Park <kmpark@infradead.org>
2009-06-12 20:45:47 +02:00
Stefan Roese
0a57265533 mtd: Add MTD concat support to concatenate multiple MTD NOR devices
This patch adds concatenation support to the U-Boot MTD infrastructure.
By enabling CONFIG_MTD_CONCAT this MTD CFI wrapper will concatenate
all found NOR devices into one single MTD device. This can be used by
e.g by UBI to access a partition that spans over multiple NOR chips.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-06-12 20:45:47 +02:00
Wolfgang Grandegger
33846df28f Add wait flags to support board/chip specific delays
The NAND flash on the TQM8548_BE modules requires a short delay after
running the UPM pattern like the MPC8360ERDK board does. The TQM8548_BE
requires a further short delay after writing out a buffer. Normally the
R/B pin should be checked, but it's not connected on the TQM8548_BE.
The corresponding Linux FSL UPM driver uses similar delay points at the
same locations. To manage these extra delays in a more general way, I
introduced the "wait_flags" field allowing the board-specific driver to
specify various types of extra delay.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:40 -05:00
Wolfgang Grandegger
06e9f7df05 Add support for TQM-specific chip select logic to FSL-UPM
For the NAND chips on the TQM8548 modules, a special chip-select logic is
used. It uses dedicated address lines to be set via UPM machine address
register (mar). This patch adds such support to the FSL-UPM driver.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:39 -05:00
Wolfgang Grandegger
e93c1c169d Add multi chip support to the FSL-UPM driver
This patch adds support for multi-chip NAND devices to the FSL-UPM
driver. The "dev_ready" callback of the "struct fsl_upm_nand" is now
called with the argument "chip_nr" to allow testing the proper chip
select line. The NAND support of the MPC8360ERDK is updated as well.
No other boards are currently using the FSL UPM driver.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-03-23 15:53:38 -05:00
Wolfgang Grandegger
6c869637fe NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and
changes the default from 8 to 1 for the legacy and the new MTD
NAND layer. This allows to remove all NAND_MAX_CHIPS definitions
in the board config files because none of the boards use multi
chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440
define

 #define NAND_MAX_CHIPS          CONFIG_SYS_MAX_NAND_DEVICE

but that's bogus and did not work anyhow.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:51 -06:00
Stefan Roese
1ae3986204 OneNAND: Additional sync with 2.6.27
- Add subpage write support
- Add onenand_oob_64/32 ecclayout

This has been missing and without it UBI has some incompatibilies issues
with the current (>= 2.6.27) Linux kernel version. vid_hdr_offset is
placed differently (2048 instead of 512) without this fix.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23 10:32:48 -06:00
Kyungmin Park
ef0921d6b0 Sync with 2.6.27
Sync with OneNAND kernel codes

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-01-23 10:32:44 -06:00
Wolfgang Denk
455ae7e87f Coding style cleanup, update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-16 01:02:17 +01:00
Kyungmin Park
58be3a1056 UBI: Add basic UBI support to U-Boot (Part 8/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Kyungmin Park
47ae6693f5 UBI: Add basic UBI support to U-Boot (Part 7/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Kyungmin Park
7e6ee7ad27 UBI: Add basic UBI support to U-Boot (Part 6/8)
This patch adds basic UBI (Unsorted Block Image) support to U-Boot.
It's based on the Linux UBI version and basically has a "OS"
translation wrapper that defines most Linux specific calls
(spin_lock() etc.) into no-ops. Some source code parts have been
uncommented by "#ifdef UBI_LINUX". This makes it easier to compare
this version with the Linux version and simplifies future UBI
ports/bug-fixes from the Linux version.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-19 20:34:39 +01:00
Alessandro Rubini
a47f957ab5 NAND: Allow NAND and OneNAND to coexist
This removes in nand.h code that is verbatim duplicated from bbm.h,
including directly bbm.h in nand.h. The previous state of affairs
prevented compiling code for a board hosting both NAND and OneNAND chips.

Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-31 16:37:53 -05:00
Scott Wood
c45912d8ab NAND: sync with 2.6.27
This brings the core NAND code up to date with the Linux kernel.

Since there were several drivers in Linux as of the last update that are
not in u-boot, I'm not bringing over new drivers that have been added
since in the absence of an interested party.

I did not update OneNAND since it was recently synced by Kyungmin Park,
and I'm not sure exactly what the common ancestor is.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-10-29 10:42:16 -05:00
Kyungmin Park
bfd7f38614 Fix OneNAND read_oob/write_oob functions compatability
Also sync with kernel OneNAND codes

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-21 13:50:20 -05:00
Wolfgang Denk
4b0708093e Coding Style cleanup, update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-08-14 14:41:06 +02:00
Wolfgang Denk
28ac671910 Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2008-08-14 11:26:22 +02:00
Kyungmin Park
d438d50848 Fix OneNAND build break
Since page size field is changed from oobblock to writesize. But OneNAND is not updated.
- fix bufferram management at erase operation
This patch includes the NAND/OneNAND state filed too.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-13 11:00:19 -05:00
Jean-Christophe PLAGNIOL-VILLARD
cc4a0ceeac drivers/mtd/nand: Move conditional compilation to Makefile
rename CFG_NAND_LEGACY to CONFIG_NAND_LEGACY

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-08-13 01:40:43 +02:00
Ilya Yanok
13f0fd94e3 NAND: Scan bad blocks lazily.
Rather than scanning on boot, scan upon the first attempt to check the
badness of a block.  This speeds up boot when not using NAND, and reduces
the likelihood of needing to reflash via JTAG if NAND becomes
nonfunctional.

Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:28 -05:00
Anton Vorontsov
e1c3dbada3 nand: fsl_upm: convert to updated MTD NAND infrastructure
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:27 -05:00
William Juul
5e1dae5c3d Fixing coding style issues
- Fixing leading white spaces
 - Fixing indentation where 4 spaces are used instead of tab
 - Removing C++ comments (//), wherever I introduced them

Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:17 -05:00
William Juul
4cbb651b29 Remove white space at end.
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:16 -05:00
William Juul
cfa460adfd Update MTD to that of Linux 2.6.22.1
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.

This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.

MAKEALL ppc/arm has some issues:
 * DOC/OneNand/nand_spl is not building (I have not tried porting
   these parts, and since I do not have any HW and I am not familiar
   with this code/HW I think its best left to someone else.)

Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
 cpu/ppc4xx/ndfc.c
 cpu/arm926ejs/davinci/nand.c
 board/delta/nand.c
 board/zylonite/nand.c

Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-12 11:31:15 -05:00
Scott Wood
3167c5386e NAND: Rename DEBUG to MTDDEBUG to avoid namespace pollution.
This is particularly problematic now that non-NAND-specific code is
including <nand.h>, and thus all debugging code is being compiled
regardless of whether it was requested, as reported by Scott McNutt
<smcnutt@psyent.com>.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-07-09 17:24:47 -05:00
Sergei Poselenov
248ae5cfc8 NAND: Added support for 128-bit OOB, adapted
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
2008-06-11 00:30:22 -05:00
Wolfgang Grandegger
a75a57ef6e NAND FSL UPM: driver re-write using the hwcontrol callback
This is a re-write of the NAND FSL UPM driver using the more universal
hwcontrol callback (instead of the cmdfunc callback). Here is a brief
list of furher modifications:

- For the time being, the UPM setup writing the UPM array has been
  removed from the driver and must now be done by the board specific
  code.

- The bus width definition in "struct fsl_upm_nand" is now in bits to
  comply with the corresponding Linux driver and 8, 16 and 32 bit
  accesses are supported.

- chip->dev_read is only set if fun->dev_ready != NULL, which is
  required for boards not connecting the R/B pin.

- A few issue have been fixed with MxMR bit manipulation like in the
  corresponding Linux driver.

Note: I think the "io_addr" field of "struct fsl_upm" could be removed
      as well, because the address is already determined by
      "nand->IO_ADDR_[RW]", but I'm not 100% sure.

This patch has been tested on a TQM8548 modules with the NAND chip
Micron MT29F8G08FABWP.

This patch is based on the following patches posted to this list a few
minutes ago:

  PPC: add accessor macros to clear and set bits in one shot
  83xx/85xx/86xx: add more MxMR local bus definitions

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-06-10 18:22:26 -05:00
Scott Wood
135f0a7488 NAND: Provide a sane default for NAND_MAX_CHIPS.
This allows the header to be included regardless of whether a board's
config file provides NAND-related defininitions.

Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-05-28 11:06:24 -05:00
Wolfgang Denk
53677ef18e Big white-space cleanup.
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-21 00:14:08 +02:00
Anton Vorontsov
cd9d23053d nand: FSL UPM NAND driver
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-01-16 14:14:40 +01:00
Marcel Ziswiler
10c7382bc5 fix various comments
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2008-01-09 21:50:47 +01:00
Kyungmin Park
d7e8ce101a OneNAND support (take #2)
[PATCH 3/3] OneNAND support (take #2)

OneNAND support at U-Boot

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2007-09-17 08:19:08 +02:00
Ulf Samuelsson
7ebb4479b0 [PATCH][NAND] Define the Vendor Id for Micron NAND Flash
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2007-05-24 12:12:47 +02:00
Stefan Roese
887e2ec9ec Add support for AMCC Sequoia PPC440EPx eval board
- Add support for PPC440EPx & PPC440GRx
- Add support for PPC440EP(x)/GR(x) NAND controller
  in cpu/ppc4xx directory
- Add NAND boot functionality for Sequoia board,
  please see doc/README.nand-boot-ppc440 for details
- This Sequoia NAND image doesn't support environment
  in NAND for now. This will be added in a short while.
Patch by Stefan Roese, 07 Sep 2006
2006-09-07 11:51:23 +02:00
Wolfgang Denk
b9365a26a1 Code cleanup 2006-07-21 11:56:05 +02:00
Marian Balakowicz
2fc000d756 Remove dependencies between DoC code and old legacy NAND driver.
Necessary defines and data structures were copied to DoC specific files
so that legacy NAND code could be entirely removed from u-boot tree
in the near future.
2006-04-05 20:46:41 +02:00
Wolfgang Denk
bfc81252c0 Minor code cleanup 2006-03-06 13:03:37 +01:00
Bartlomiej Sieka
addb2e1650 Re-factoring the legacy NAND code (legacy NAND now only in board-specific
code and in SoC code). Boards using the old way have CFG_NAND_LEGACY and
BOARDLIBS = drivers/nand_legacy/libnand_legacy.a added. Build breakage for
NETTA.ERR and NETTA_ISDN - will go away when the new NAND support is
implemented for these boards.
2006-03-05 18:57:33 +01:00
Bartlomiej Sieka
038ccac511 Merge with /home/wd/git/u-boot/testing-NAND/ to add new NAND handling. 2006-02-24 09:37:22 +01:00
Wolfgang Denk
ac7eb8a315 Update of new NAND code
Patch by Ladislav Michl, 13 Sep 2005
2005-09-14 23:53:32 +02:00
Wolfgang Denk
932394ac43 Rewrite of NAND code based on what is in 2.6.12 Linux kernel
Patch by Ladislav Michl, 29 Jun 2005
2005-08-17 12:55:25 +02:00
wdenk
384cc68744 Patches by Josef Wagner, 29 Oct 2004:
- Add support for MicroSys CPU87 board
- Add support for MicroSys PM854 board
2005-04-03 22:35:21 +00:00
wdenk
a43278a43d * Patch by Gary Jennejohn, 11 Sep 2003:
- allow for longer timeouts for USB mass storage devices

* Patch by Denis Peter, 11 Sep 2003:
  - fix USB data pointer assignment for bulk only transfer.
  - prevent to display erased directories in FAT filesystem.

* Change output format for NAND flash - make it look like for other
  memory, too
2003-09-11 19:48:06 +00:00
wdenk
1f4bb37d6b * Patch by Scott McNutt, 21 Jul 2003:
Add support for LynuxWorks Kernel Downloadable Images (KDIs).
  Both LynxOS and BlueCat linux KDIs are supported.

* Patch by Richard Woodruff, 25 Jul 2003:
  use more reliable reset for OMAP/925T

* Patch by Nye Liu, 25 Jul 2003:
  fix typo in mpc8xx.h

* Patch by Richard Woodruff, 24 Jul 2003:
  Fixes for cmd_nand.c:
  - Fixed null dereferece which could result in incorrect ECC values.
  - Added support for devices with no Ready/Busy signal hooked up.
  - Added OMAP1510 read/write protect handling.
  - Fixed nand.h's ECCPOS. A conflict existed with POS5 and badblock
    for non-JFFS2.
  - Switched default ECC to be JFFS2.
2003-07-27 00:21:01 +00:00
wdenk
8bde7f776c * Code cleanup:
- remove trailing white space, trailing empty lines, C++ comments, etc.
  - split cmd_boot.c (separate cmd_bdinfo.c and cmd_load.c)

* Patches by Kenneth Johansson, 25 Jun 2003:
  - major rework of command structure
    (work done mostly by Michal Cendrowski and Joakim Kristiansen)
2003-06-27 21:31:46 +00:00
wdenk
592c5cabe7 Patch by Murray Jensen, 20 Jun 2003:
- hymod update
- cleanup (especially for gcc-3.x compilers)
2003-06-21 00:17:24 +00:00
wdenk
7a8e9bed17 * Patch by Marc Singer, 29 May 2003:
Fixed rarp boot method for IA32 and other little-endian CPUs.

* Patch by Marc Singer, 28 May 2003:
  Added port I/O commands.

* Patch by Matthew McClintock, 28 May 2003
  - cpu/mpc824x/start.S: fix relocation code when booting from RAM
  - minor patches for utx8245

* Patch by Daniel Engström, 28 May 2003:
  x86 update

* Patch by Dave Ellis, 9 May 2003 + 27 May 2003:
  add nand flash support to SXNI855T configuration
  fix/extend nand flash support:
  - fix 'nand erase' command so does not erase bad blocks
  - fix 'nand write' command so does not write to bad blocks
  - fix nand_probe() so handles no flash detected properly
  - add doc/README.nand
  - add .jffs2 and .oob options to nand read/write
  - add 'nand bad' command to list bad blocks
  - add 'clean' option to 'nand erase' to write JFFS2 clean markers
  - make NAND read/write faster

* Patch by Rune Torgersen, 23 May 2003:
  Update for MPC8266ADS board
2003-05-31 18:35:21 +00:00
wdenk
ac6dbb85b7 Make compile clean, fix the usual small problems. 2003-03-26 11:42:53 +00:00
wdenk
dc7c9a1a52 * Patch by Rick Bronson, 16 Mar 2003:
Add support for Atmel AT91RM9200DK w/NAND

* Patches by Robert Schwebel, 19 Mar 2003:
  - use arm-linux-gcc as default compiler for ARM
  - fix i2c fixup code
  - fix missing baudrate setting
  - added $loadaddr / CFG_LOAD_ADDR support to loadb
  - moved "ignoring trailing characters" _before_ u-boot wants to
    print out diagnostics messages; removes bogus characters at the
    end of transmission

* Patch by John Zhan, 18 Mar 2003:
  Add support for SinoVee Microsystems SC8xx boards

* Patch by Rolf Offermanns, 21 Mar 2003:
  ported the dnp1110 related changes from the current armboot cvs to
  current u-boot cvs. smc91111 does not work. problem marked in
  smc91111.c, grep for "FIXME".

* Patch by Brian Auld, 25 Mar 2003:
  Add support for STM flash chips on ebony board

 * Add PCI support for MPC8250 Boards (PM825 module)

 * Patch by Stefan Roese, 25 Mar 2003:
2003-03-26 06:55:25 +00:00
wdenk
e221174377 Initial revision 2002-11-02 23:30:20 +00:00
wdenk
012771d88a Initial revision 2002-03-08 21:31:05 +00:00
wdenk
a1e329b41b Initial revision 2002-01-26 00:07:42 +00:00