Commit graph

72 commits

Author SHA1 Message Date
Jyri Sarha
8c17cbdf8a arm: am33xx: Initialize EMIF REG_PR_OLD_COUNT for BBB and am335x-evm
Initialize EMIF OCP_CONFIG registers REG_COS_COUNT_1, REG_COS_COUNT_2,
and REG_PR_OLD_COUNT field for Beaglebone-Black and am335x-evm. With
the default values LCDC suffers from DMA FIFO underflows and frame
synchronization lost errors. The initialization values are the highest
that work flawlessly when heavy memory load is generated by CPU. 32bpp
colors were used in the test. On BBB the video mode used 110MHz pixel
clock. The mode supported by the panel of am335x-evm uses 30MHz pixel
clock.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-09 15:00:03 -05:00
Lokesh Vutla
5d4d436c6d ARM: AMx3xx: Make FIT boot as default boot on HS devices
Verification has to be done before booting any images on HS devices. So
default the boot to FIT on HS devices.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:09 -05:00
Lokesh Vutla
140d76a9ee board: ti: amx3xx: Remove multiple EEPROM reads
Detect the board very early and avoid reading eeprom multiple times.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-21 13:59:25 -05:00
Roger Quadros
f411b5cca4 board: am335x: Always set eth/eth1addr environment variable
Ethernet ports might be used in the kernel even if CPSW driver
is disabled at u-boot. So always set ethaddr and eth1addr
environment variable from efuse.

Retain usbnet_devaddr as it is required for SPL USB eth boot.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13 12:25:10 -05:00
Roger Quadros
e607ec993b board: am335x-icev2: add ethernet phy mode detection logic
Both ethernet ports can be used as CPSW ethernet (RMII mode)
or PRU ethernet (MII mode) by setting the jumper near the port.
Read the jumper value and set the pinmux, external mux and
PHY clock accordingly.

As jumper line is overridden by PHY RX_DV pin immediately
after bootstrap (power-up/reset), we have to use GPIO edge
detection to capture the jumper line status.

As u-boot doesn't provide any infrastructure for GPIO edge
detection, we directly access the GPIO registers.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-13 12:25:06 -05:00
Andrew F. Davis
b0a4eea1a0 board: am33xx-hs: Allow post-processing of FIT image on AM33xx
When CONFIG_FIT_IMAGE_POST_PROCESS or CONFIG_SPL_FIT_IMAGE_POST_PROCESS
is enabled board_fit_image_post_process will be called, add this
function to am33xx boards when CONFIG_TI_SECURE_DEVICE is set to
verify the loaded image.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-02 08:10:01 -04:00
Lokesh Vutla
3d16389c90 board: am335x: Allow to choose serial device dynamically
Different AM335x based platforms have different serial consoles. As serial
console is Kconfig option a separate defconfig has to be created for each
platform. So pass the serial device dynamically.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:54 -04:00
Lokesh Vutla
73ec696059 ARM: dts: AM335x-ICEv2: Add minimal dts support
Add minimal dts support for AM335x-ICEv2 board

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-05-27 15:47:53 -04:00
Lokesh Vutla
97f3a178b2 board: AM335x-ICEv2: Add cpsw support
In order to enable cpsw on AM335x ICEv2 board, the following needs to be done:

1)There are few on board jumper settings which gives a choice between
cpsw and PRUSS, that needs to be properly selected[1]. Even after selecting
this, there are few GPIOs which control these muxes that needs to be held high.

2) The clock to PHY is provided by a PLL-based clock synthesizer[2] connected
via I2C. This needs to properly programmed and locked for PHY operation.
And PHY needs to be reset before before being used, which is also held by
a GPIO.

3) RMII mode needs to be selected.

[1] http://www.ti.com/lit/zip/tidr336
[2] http://www.ti.com/lit/ds/symlink/cdce913.pdf

Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:52 -04:00
Lokesh Vutla
d8ff4fdb10 board: AM335x-ICEv2: Add DDR data
AM335x ICEv2 contains a 2Gbit(128Mx16) of DDR3 SDRAM(MT41J128M16JT-125),
capable of running at 400MHz. Adding this specific DDR configuration
details running at 400MHz.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:51 -04:00
Lokesh Vutla
da9d9599ac ARM: dts: AM335x-BBG: Add initial support
Add initial DTS support for AM335x-BBG

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:49 -04:00
Lokesh Vutla
3819ea7063 ARM: dts: AM335x-evmsk: Add initial support
Add initial DTS support for AM335x-evm sk.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:49 -04:00
Lokesh Vutla
505ea6e82a board: am33xx: fit: add support for selecting dtb dynamically
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:47:47 -04:00
Nishanth Menon
770e68c0a3 ti: AM335x: Use generic EEPROM detection logic
Use the generic EEPROM detection logic instead of duplicating the AM
eeprom logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Steven Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:33 -04:00
robertcnelson@gmail.com
dfd1bb4ec8 board/ti/am335x: add support for BeagleBone Green
SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).

This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35  42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]

http://beagleboard.org/green
http://www.seeedstudio.com/wiki/Beaglebone_green

In Mainline Kernel as of:
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=79a4e64c679d8a0b1037da174e4aea578c80c4e6

Patch tested on BeagleBone Black (rev C) and BeagleBone Green (production model)

Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-11-18 14:50:07 -05:00
Mugunthan V N
bd83e3df45 am335x_evm: prepare for eth driver model support
Prepare board file so that ethernet registration are
commented for DM conversion

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:18:33 -04:00
Paul Kocialkowski
95de1e2f26 usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSB
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2015-08-05 17:20:34 +02:00
Joe Hershberger
0adb5b761f net: cosmetic: Name ethaddr variables consistently
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:32 -06:00
Tom Rini
1286b7f6ca am335x_evm: Convert CONFIG_CONS_INDEX into a menu choice
- Drop CONFIG_SERIAL[1-6] and use CONFIG_CONS_INDEX tests instead
- Add choice and help text to board/ti/am335x/Kconfig
- Correct comment about IDK in board/ti/am335x/mux.c
- Remove am335x_evm_uart* defconfig files as they're just variations
  on a config option now.

Signed-off-by: Tom Rini <trini@ti.com>
2014-08-25 10:48:13 -04:00
Tom Rini
c4f80f5003 am335x_evm / gumstix pepper: Correct DDR settings
As noted by clang, we have been shifting certain values out of 32bit
range when setting some DDR registers.  Upon further inspection these
had been touching reserved fields (and having no impact).  These came in
from historical bring-up code and can be discarded.  Similarly, we had
been declaring some fields as 0 when they will be initialized that way.
Tested on Beaglebone White.

Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Cc: Ash Charles <ash@gumstix.com>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-By: Ash Charles <ashcharles@gmail.com>
2014-07-25 16:26:08 -04:00
Tom Rini
d0e6d34d7c am335x: Switch to CONFIG_SKIP_LOWLEVEL_INIT from guarding SPL or NOR_BOOT
In the case of SPL or NOR_BOOT (no SPL involved) we need to include
certain code in the build.  Use !CONFIG_SKIP_LOWLEVEL_INIT rather than
CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to
make supporting XIP QSPI boot clearer in the code.

Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
2014-04-17 17:24:40 -04:00
Tom Rini
ba9a6708ec am335x_evm: Make SPL_OS also check the boot_os variable for falcon mode
We use the same variable as a3m071 in the environment to determine if we
should boot into Linux or U-Boot.  This is useful on boards like
Beaglebone Black or AM335x GP EVM where we have persistent storage for
the environment.

Signed-off-by: Tom Rini <trini@ti.com>
2014-04-17 14:39:54 -04:00
Tom Rini
68996b84b6 am335x_evm: Clarify when we build board_eth_init
If we build this function in cases where we would be discarding it
anyhow we still end up with maybe unused warnings.  Rather than litter
the function with __maybe_unused, just spell out when to build it.

Signed-off-by: Tom Rini <trini@ti.com>
2014-03-28 15:15:10 -04:00
Mugunthan V N
a35ad51efe ARM: AM335x: add support for reading cpsw 2nd mac address from efuse
Adding support for reading cpsw 2nd mac address from efuse and pass it
to kernel via dtb which will be used in dual emac mode of cpsw.
Also adding mii command support to am335x common config.

Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-03-04 09:42:06 -05:00
Mugunthan V N
9c653aad16 drivers: net: cpsw: add support to have phy address from cpsw platform data
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
2014-03-04 09:41:53 -05:00
Lokesh Vutla
965de8b91b ARM: AM33xx+: Update ioregs to pass different values
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-18 21:14:18 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Tom Rini
39245c8699 am33xx: Stop modifying certain EMIF4D registers
Based on the definitive guide to EMIF configuration[1] certain registers
that we have been modifying (and are documented registers) should be
left in their reset values rather than modified.  This has been tested
on AM335x GP EVM and Beaglebone White.

[1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
2013-12-04 08:11:45 -05:00
Tom Rini
faca8ff55f Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2013-11-25 10:42:13 -05:00
pekon gupta
2c17e6d1d9 am335x: fix GPMC config for NAND and NOR SPL boot
GPMC controller is common IP to interface with both NAND and NOR flash devices.
Also, it supports max 8 chip-selects, which can be independently connected to
any of the devices.
But ROM code expects the boot-device to be connected to only chip-select[0].
Thus to resolve conflict between NOR and NAND boot. This patch:
- combines NOR and NAND configs spread in board files to common gpmc_init()
- configures GPMC based on boot-mode selected for SPL boot.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Tom Rini
6843918e00 am335x: Enable CONFIG_OMAP_WATCHDOG support
There is a board-specific portion for calling watchdog enable itself, in
main U-Boot.

Signed-off-by: Tom Rini <trini@ti.com>
2013-11-01 15:55:59 -04:00
Steve Kipisz
52f7d8442e am335x:Handle worst case scenario for Errata 1.0.24
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset,
the boot ROM sets the frequencies for OPP100. This patch attempts to
drop the frequencies back to OPP50 as soon as possible in the SPL. Then
later the voltages and frequencies up set higher.

Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Adapt to current framework]
Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 16:57:40 -04:00
Tom Rini
9721027aae am335x_evm: am33xx_spl_board_init function and scale core frequency
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on.  In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed.  In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz.  In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1.  As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe.  In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.

Signed-off-by: Tom Rini <trini@ti.com>
2013-09-20 16:57:35 -04:00
Heiko Schocher
dafd4db33a arm, am33xx: add defines for gmii_sel_register bits
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-08-28 11:44:59 -04:00
Tom Rini
73feefdc1a am33xx: Stop using PHYS_DRAM_1 define
We defined PHYS_DRAM_1 to 0x80000000 (start of DRAM) and then used this
for CONFIG_SYS_SDRAM_BASE.  But then we kept on referencing PHYS_DRAM_1
in other places.  Change to directly setting CONFIG_SYS_DRAM_BASE and
then using that name in code.

Signed-off-by: Tom Rini <trini@ti.com>
2013-08-15 18:38:35 -04:00
Heiko Schocher
0660481a59 ARM: AM33xx: Move s_init to a common place
s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
95cb69faeb ARM: AM33xx: Cleanup clocks layer
Cleaning up the clocks layer.
This helps in addition of new Soc with minimal
changes.
This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Lokesh Vutla
94d77fb656 ARM: AM33xx: Cleanup dplls data
Locking sequence for all the dplls is same.
In the current code same sequence is done repeatedly
for each dpll. Instead have a generic function
for locking dplls and pass dpll data to that function.

This is derived from OMAP4 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2013-08-15 08:51:10 -04:00
Steve Kipisz
c5c7a7c32d am335x_evm: Add support to boot from NOR.
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on.  When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB.  We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.

We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Steve Kipisz
cd8845d7a4 am335x_evm: Add support for the NOR module on the memory cape
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.

Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Tom Rini
ace4275eb3 am335x_evm: Rework board_is_foo() checks
We rework the various board_is_foo() checks to take a pointer to
struct am335x_baseboard_id rather than using a local copy in board.c.
This allows us to make use of the same checks in mux.c as well as fixing
problems when this code could be running from read-only memory.

Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-30 09:21:41 -04:00
Mugunthan V N
2bf36ac638 drivers: net: cpsw: remove hard coding bd ram for cpsw
BD ram address may vary in various SOC, so removing the hardcoding and
passing the same information through platform data

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Tom Rini
348e47f766 Merge branch 'master' of git://git.denx.de/u-boot-arm 2013-06-22 07:38:12 -04:00
Heiko Schocher
7ea7f689ca arm, am33xx: move uart soft reset code to common place
move uart soft reset code to common place and call
this function from board code, instead of copy and paste
this code for every board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
[trini: Fix igep0033 build, remove 'regval' on pcm051]
Signed-off-by: Tom Rini <trini@ti.com>
2013-06-18 10:40:06 -04:00
Heiko Schocher
49f7836500 arm, am33xx: move rtc32k_enable() to common place
move rtc32k_enable() to common place so all am33xx boards can use it.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Matt Porter <mporter@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Tom Rini <trini@ti.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
2013-06-18 09:12:38 -04:00
Tom Rini
41341221d1 Merge branch 'master' of git://git.denx.de/u-boot-arm
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR

Conflicts:
	arch/arm/include/asm/arch-omap5/omap.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-06-13 15:16:15 -04:00
Joel A Fernandes
a662e0c345 am33xx: Board: Make CPSW section of ethernet initialization depend on CPSW driver
Not doing so breaks cases where CPSW is not required such as for USB RNDIS network boot.

Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
2013-06-10 08:43:08 -04:00
Peter Korsgaard
12d7a47420 am335x: enable falcon boot mode for mmc (raw and fat) and nand
Jump into full u-boot mode if a 'c' character is received on the uart.

We need to adjust the spl bss/malloc area to not overlap with the
loadaddr of the kernel (sdram + 32k), so move it past u-boot instead.

For raw mmc, we store the kernel parameter area in the free space after
the MBR (if used). For nand, we use the last sector of the partition
reserved for u-boot.

This also enables the spl command in the full u-boot so the kernel
parameter area snapshot can be created.

Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
2013-06-07 14:17:01 -04:00