Currently, a random MAC address is assigned to eth1 in Linux.
Fix this behavor by retrieving the second MAC address from the fuses.
Signed-off-by: Fabio Estevam <festevam@denx.de>
On the XEA (imx287) system the FAT file system is not used neither in
SPL nor u-boot proper.
Hence, to save ~6KiB of u-boot.img size - it has been disabled.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The XEA system (imx287 based) is not using support for EXTLINUX and VBE.
As those configuration options have been enabled by default with modern
Kconfig it is safe to explicitly disable them.
After that change the u-boot.img size has been reduced by ~16 KiB.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Drive CTRL_SLEEP_MOCI# high at boot (SPL) using a GPIO hog, this signal
may be used to control some power-rails on the carrier board, therefore
it should be set to high when the module is booting.
To do this as early as possible is generally a good idea and the issue
was noticed on the Yavia carrier board where it is needed to power the
I2C EEPROM on the carrier board.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable CONFIG_SPL_GPIO_HOG option to be able to control GPIO hogs from
SPL.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drive CTRL_SLEEP_MOCI# high at boot (SPL) using a GPIO hog, this signal
may be used to control some power-rails on the carrier board, therefore
it should be set to high when the module is booting.
To do this as early as possible is generally a good idea and the issue
was noticed on the Yavia carrier board where it is needed to power the
I2C EEPROM on the carrier board.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable CONFIG_SPL_GPIO_HOG option to be able to control GPIO hogs from
SPL.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The USB Power domains should not have been removed as it causes
the board to hang if the USB is started.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Several changes have been made to the device tree
in the kernel, so update that as well as the
corresponding imx8mp-u-boot.dtsi files to prevent
breaking the booting.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
There are some newer clocks added to the kernel recently,
so to fix prepare for resycing the device trees, update
the clock list. Since there are some minor changes to
the USB clocks, update which USB clocks are enabled
to match with the upstream kernel as well.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
For SOM with the EC configuration, the ethernet PHY is located on the
SOM itself, and connected to the CPU ethernet controller. It has a
reset line controlled via GPIO1_IO9. In this configuration, the PHY
located on the carrier board is not connected to anything and is
therefore not used.
For SOM without EC configuration, the ethernet PHY on the carrier
board is connected to the CPU ethernet controller. It has a reset line
controlled via the GPIO expander PCA9534_IO5.
The hardware configuration (EC) is determined at runtime by
reading from the SOM EEPROM.
To support both hardware configurations (EC and non-EC), adjust/fix
the PHY reset gpios according to the hardware configuration
read at runtime from the SOM EEPROM. This adjustement is done in
U-Boot (OF_BOARD_FIXUP) and kernel (OF_BOARD_SETUP) device trees.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
In case the i.MX8M Plus starts from eMMC BOOT1/BOOT2 HW partitions, the
flash.bin container is stored at offset 0 from the start, that means the
fitImage itb is at offset 0x2c0 instead of 0x300 sectors from the start.
Handle this difference in custom spl_mmc_get_uboot_raw_sector() .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Bitwise operations on signed integers are not defined,
replace them with per-call checks.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
This also needs to occur in the SPL so enable CONFIG_SPL_BOARD_INIT and
add a void spl_board_init function which calls arch_misc_init to probe
the CAAM driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Update RAM Timings for 2GB RAM based on DDR Controller Configuration
Spreadsheet revision 22. Including the update of the refresh
rate to workaround errata ERR050805.
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
The csf_spl.txt and csf_fit.txt templates contain file paths which must
be edited for the location of your NXP CST generated key files.
Streamline the process of signing an image by assigning unique var names
to these which can be expended from env variables in the csf.sh script.
The following vars are used:
SRK_TABLE - full path to SRK_1_2_3_4_table.bin
CSF_KEY - full path to the CSF Key CSF1_1_sha256_4096_65537_v3_usr_crt.pem
IMG_KEY - full path to the IMG Key IMG1_1_sha256_4096_65537_v3_usr_crt.pem
Additionally provide an example of running the csf.sh script.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The sec_in32 preprocessor is defined as follows in include/fsl_sec.h file:
When address "a" is calculated using math for ex: addition of base address and
an offset, then casting is applied only to the first address which in this
example is base address.
caam_ccbvid_reg = sec_in32(CONFIG_SYS_FSL_SEC_ADDR + CAAM_CCBVID_OFFSET)
resolves to:
caam_ccbvid_reg = in_le32((ulong *)(ulong)CONFIG_SYS_FSL_SEC_ADDR +
CAAM_CCBVID_OFFSET)
instead it should resolve to:
caam_ccbvid_reg = in_le32((ulong *)(ulong)(CONFIG_SYS_FSL_SEC_ADDR +
CAAM_CCBVID_OFFSET))
Thus add parenthesis around the address "a" so that however the address is
calculated, the casting is applied to the final calculated address.
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
add support for SHA-256 secure hash algorithm using the ARM v8
SHA-256 instructions for verifying image hash.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Abstract common interfaces for AHAB authentication operations.
Then share some common codes for AHAB and SPL container authentication
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If the container has image which conflicts with
spl_get_load_buffer address, there are processing failures.
Use malloc instead of spl_get_load_buffer.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Nitin Garg <nitin.garg@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
1. Implement bootaux for the M4 boot on i.MX8QM and QXP. Users need to download
M4 image to any DDR address first. Then use the
"bootaux <M4 download DDR address> [M4 core id]" to boot CM4_0
or CM4_1, the default core id is 0 for CM4_0.
Since current M4 only supports running in TCM. The bootaux will copy
the M4 image from DDR to its TCML.
2. Implment bootaux for HIFI on QXP
command: bootaux 0x81000000 1
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The bootaux uses ulong to read private data and write to M4 TCM,
this cause problem on ARM64 platform where the ulong is 8bytes.
Fix it by using u32 to replace ulong.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current bootaux supports i.MX8M and i.MX93, but the name "_M4_"
implies that the SoCs have Cortex-M4. Actually i.MX8MM/Q use Cortex-M4,
i.MX8MN/P use Cortex-M7, i.MX93 use Cortex-M33, so use "_MCU_" in place
of "_M4_" to simplify the naming.
Signed-off-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the support for loading image from secondary container set on
iMX8QM B0, iMX8QXP C0.
Using the SCFW API to get container set index, if it is the secondary
boot, get the offset from fuse and apply to offset of current container
set beginning for loading.
Also override the emmc boot partition to check secondary boot and switch
to the other boot part.
This patch is modified from NXP downstream:
imx8: Fix the fuse used by secondary container offset
imx: container: Skip container set check for ROM API
imx8: spl: Support booting from secondary container set
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Checking container header tag and version is wrong, it causes to fail
to bypass invalid container
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix below coverity issues caused by get_idx function where "-1" is
compared with uint8_t "element"
343336 Unsigned compared with neg
343337 Operands don't affect result
Additional, this function returns "-1" will cause overflow to
event string array.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On the imx8ulp A1 SoC, the ELE RNG needs to be manually started.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Extend the RX timeout value to 10s, because when authentication is failed
the ELE needs long time (>2s for 28M image) to return the result. Print
rx wait info per 1s.
Also correct TX and RX status registers in debug.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to SRM, the Sentinel MU has 8 TR and 4 RR registers. All
of them are used for ELE message. So update TR count to 8 and fix a
typo in receive msg
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity (CID 21143558).
When tee_shm_register returns failure, the shm_input pointer is
invalid, should not free it. Same issue also exists on registering
shm_output.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add two ELE API: ele_return_lifecycle_update and ele_write_secure_fuse
Add two cmd: ahab_return_lifecycle and ahab_sec_fuse_prog
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix build warning:
warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3
has type ‘u64’ {aka ‘long long unsigned int’} [-Wformat=]
printf("can't find memreg for image %d load address 0x%x, error %d\n",
warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but
argument 3 has type ‘sc_faddr_t’ {aka ‘long long unsigned int’} [-Wformat=]
debug("memreg %u 0x%lx -- 0x%lx\n", mr, start, end);
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The return value is int type, not sc_err_t(u8), correct the usage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
