Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Enable CONFIG_SOC_DEVICE and CONFIG_SOC_DEVICE_TI_K3 so the TI K3 SoC
driver can be used for SoC detection.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.
Before this change it was necessary to use:
/* SPI Flash Configs */
#if defined(CONFIG_SPL_BUILD)
#undef CONFIG_DM_SPI
#undef CONFIG_DM_SPI_FLASH
#undef CONFIG_SPI_FLASH_MTD
#endif
in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.
The goal of this patch:
Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.
Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).
In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):
- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
environment with no fitImage and OF_LIBFDT support).
Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.
This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
Due to how the Makefile logic is we currently get DM_SPI support in SPL
enabled by having DM_SPI enabled for full U-Boot but not having
CONFIG_SPL_DM_SPI set. Add this missing option to boards that were
inadvertently making use of it.
Cc: Adam Ford <aford173@gmail.com>
Cc: Akash Gajjar <akash@openedev.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Andy Yan <andy.yan@rock-chips.com>
Cc: Anup Patel <anup.patel@wdc.com>
Cc: Atish Patra <atish.patra@wdc.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Chee Hong Ang <chee.hong.ang@intel.com>
Cc: Chin-Liang See <clsee@altera.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Klaus Goger <klaus.goger@theobroma-systems.com>
Cc: Levin Du <djw@t-chip.com.cn>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Suniel Mahesh <sunil@amarulasolutions.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Wolfgang Grandegger <wg@aries-embedded.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
ti_phy_init function was allocated to the DP83867 PHY. This function
name is to generic for a specific PHY. The function can be moved to a
TI specific file that can register all TI PHYs that are defined in the
defconfig. The ti_phy_init file will contain all TI PHYs initialization
so that only phy_ti_init can be called from the framework.
In addition to the above the config flag for the DP83867 needs to be changed
in the Kconfig and dependent defconfig files. The config flag that was
used for the DP83867 was also generic in nature so a more specific
config flag for the DP83867 was created.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Additions have been made to the non-HS defconfig without the same
being made to the HS defconfig, sync them.
Signed-off-by: Andrew F. Davis <afd@ti.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
HS devices use the FIT post processing step to authenticate boot images.
Set the configured boot command to load FIT by default.
Signed-off-by: Andrew F. Davis <afd@ti.com>
The K3 System Controller driver is used for loading and starting
the System Firmware, and is used only on R5 SPL. It need not be
enabled and built for the A53 U-Boot and SPL, so disable it from
both the GP and HS AM65x A53 defconfigs.
While at this, also remove the unneeded CONFIG_SPL_REMOTEPROC and
CONFIG_CMD_REMOTEPROC as no remoteprocs are now loaded from A53 SPL.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
k3_rproc driver is specifically meant for controlling an arm64
core using TISCI protocol. So rename the driver, Kconfig symbol,
compatible and functions accordingly.
While at it drop this remoteproc selection for a53 defconfig.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This will allow for downloading and applying overlays from an MMC/SD
boot media based on the overlay_files ENV variable containing a list
of overlay files.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The malloc pool used before relocation is getting tight leading to
out of memory errors doing certain DM-related calls. Since we are
running the A53 SPL out of DDR let's just go ahead and bump its size
as used in U-Boot proper as well as SPL (via Kconfig default value)
from 8KB to 32KB.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Enable GPIO driver for PCA953X-compatible I2C-based I/O expander
which includes support for the TCA9554/PCA9554-type expander found
on the AM654 EVM base board.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Enable I2C via driver model as well as the associated set of U-Boot
commands to allow us interacting with various I2C slave devices.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add new defconfig files for the AM65x High Security EVM.
This defconfigs are the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Dannenberg <dannenberg@ti.com>
