Commit graph

75 commits

Author SHA1 Message Date
Keerthy
9ecdf30cfe board: ti: dra71x-evm: Hook LDO1 of LP8733 to EN_PIN
All regulators are hooked to EN_Pin at reset so that EN Pin controls
their state. Hook the LDO1 regulator to EN pin which at reset is not
hooked. This applies only to LP8733.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-11-17 07:43:32 -05:00
Vishal Mahaveer
ba39608147 ARM: DRA72x: Add support for detection of DRA71x SR 2.1
DRA71x processors are reduced pin and software compatible
derivative of DRA72 processors. Add support for detection
of SR2.1 version of DRA71x family of processors.

Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-12 18:02:29 -04:00
Lokesh Vutla
fede942980 board: ti: dra76: Add dt support
Add support for selecting proper dtb for
dra76x u-boot from FIT.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-09-11 16:22:30 -04:00
Lokesh Vutla
cd43b51600 board: ti: dra76-evm: Add support for powering on mmc ldo
ldo4 is used to poweron mmc on dra76-evm. Enable it.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:43 -04:00
Lokesh Vutla
9120ef079c board: ti: dra76-evm: Add the pinmux data
Adding pinmux and IODELAY data for dra76-evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:42 -04:00
Lokesh Vutla
c9a7c17a96 board: ti: dra76-evm: Add DDR data
dra76-evm has the ddr parts connectedi running at 666MHz:
EMIF1: MT41K512M16HA-125 AIT:A  x 2
EMIF2: MT41K512M8RH-125-AAT:E x 4
Add support for configuring the above DDR parts.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:41 -04:00
Keerthy
c247605510 board: ti: dra76-evm: Add the pmic data
dra76-evm uses lp8736 and tps65917 pmic for powering on
various peripherals. Add data for these pmics and register
for dra76-evm.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:40 -04:00
Lokesh Vutla
c8c04eca30 board: ti: dra76-evm: Add epprom support
The dra76-evm is a board based on TI's DRA76 processor
Add eeprom support

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:39 -04:00
Lokesh Vutla
db4fce8fcd palmas: Add support for powering different ldos
It is not necessary that ldo1 is used to power on mmc.
So, add support for passing ldo registers for powering on mmc.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:37 -04:00
Lokesh Vutla
91d3e90668 arm: omap5+: Add board specific ldo powering
It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-09-11 16:19:35 -04:00
Simon Glass
bfebc8c965 env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()
We are now using an env_ prefix for environment functions. Rename these
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:32 -04:00
Simon Glass
00caae6d47 env: Rename getenv/_f() to env_get()
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:24 -04:00
Simon Glass
fd1e959e91 env: Rename eth_setenv_enetaddr() to eth_env_set_enetaddr()
Rename this function for consistency with env_set().

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:23:56 -04:00
Simon Glass
382bee57f1 env: Rename setenv() to env_set()
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:22:18 -04:00
Simon Glass
310fb14b26 env: Drop env_relocate_spec() in favour of env_load()
This is a strange name for a function that loads the environment. There is
now only one implementation of this function, so use the new env_load()
function directly instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-15 20:50:29 -04:00
Semen Protsenko
4a30a93929 arm: dra7: Set fastboot variables in environment
One can obtain those variables using next commands:

    $ fastboot getvar cpu
    $ fastboot getvar secure
    $ fastboot getvar board_rev
    $ fastboot getvar userdata_size

Those variables are needed for fastboot.sh script.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-06-12 08:36:26 -04:00
Masahiro Yamada
4aa2ba3a34 mmc: replace CONFIG_GENERIC_MMC with CONFIG_MMC
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature.  Deprecate the
former.

This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-05-15 18:28:23 +09:00
Uri Mashiach
1a9a5f7a39 usb: host: xhci-omap: fix double weak board_usb_init functions
A weak version of the function board_usb_init is implemented in:
common/usb.c
drivers/usb/host/xhci-omap.c

To fix the double implementations:
* Convert the board_usb_init function in drivers/usb/host/xhci-omap.c
  normal (not weak).
* The function board_usb_init in drivers/usb/host/xhci-omap.c calls to
  the weak function omap_xhci_board_usb_init.
* Rename board version of the function board_usb_init to
  omap_xhci_board_usb_init.
  Done only for boards that defines CONFIG_USB_XHCI_OMAP.

To achieve the same flexibility with the function board_usb_cleanup:
* Add a normal (not weak) implementation of the function
  board_usb_cleanup in drivers/usb/host/xhci-omap.c
* The function board_usb_cleanup in drivers/usb/host/xhci-omap.c calls
  to the weak function omap_xhci_board_usb_cleanup.
* Rename board version of the function board_usb_cleanup to
  omap_xhci_board_usb_cleanup.
  Done only for boards that defines CONFIG_USB_XHCI_OMAP.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
2017-05-08 11:38:37 -04:00
Lokesh Vutla
6cc96bc75a board: dra71: Fix selection of OPPs
As per the DM[1] Dated June 2016–Revised February 2017, Table 5-3,
DRA71 supports the following OPPs for various voltage domains:

VDD_MPU:	OPP_NOM
VDD_CORE:	OPP_NOM
VDD_GPU:	OPP_NOM
VDD_DSPEVE:	OPP_NOM, OPP_HIGH
VDD_IVA:	OPP_NOM, OPP_HIGH

This patch add support for selection of the above OPPs instead of
using OPP_NOM for all voltage domains.

[1] http://www.ti.com/lit/ds/symlink/dra718.pdf

Reported-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2017-04-27 16:49:04 -04:00
Simon Glass
76b00aca4f board_f: Drop setup_dram_config() wrapper
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 16:36:51 -04:00
Jean-Jacques Hiblot
d5abcf94c7 ti: boot: Register the MMC controllers in SPL in the same way as in u-boot
To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2017-03-19 22:17:14 -04:00
Lokesh Vutla
40de70fbf7 ARM: dts: dra71x-evm: Add DT support
Add DT support for dra71-evm and built it as part of FIT image.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:51 -05:00
Keerthy
f56e635099 board: ti: dra71x-evm: Add PMIC support
Add the pmic_data for LP873x PMIC which is used to power
up dra71x-evm.

Note: As per the DM[1] DRA71x supports only OP_NOM. So, updating
the efuse registers only to use OPP_NOM irrespective of any
CONFIG_DRA7_<VOLT>_OPP_{NOM,od,high} is defined.

[1] http://www.ti.com/product/DRA718/technicaldocuments

Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:50 -05:00
Lokesh Vutla
4d74804818 board: ti: dra71x-evm: Add mux settings
Add mux and iodelay settings for dra71x-evm.
Data generated using PCT_DRA71x_SR2.0_v1.0.0.0 version (June 2016).

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:49 -05:00
Lokesh Vutla
463dd22531 board: ti: dra71x-evm: Add epprom support
The dra71x-evm is a board based on TI's DRA718 processor targeting BOM-optimized
entry infotainment systems such as display audio and is a software compatible
derivative of the highly successful DRA74 and DRA72 processor families.
More information can be found here[1].

Add epprom detection for dra71-evm.

[1] http://www.ti.com/product/dra718

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:49 -05:00
Lokesh Vutla
beb71279d8 ARM: OMAP4+: Add support for dynamically selecting OPPs
It can be expected that different paper spins of a SoC can have
different definitions for OPP and can have their own constraints
on the boot up OPP for each voltage rail. In order to have this
flexibility, add support for dynamically selecting the OPP voltage
based on the board to handle any such exceptions.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:48 -05:00
Andrew F. Davis
0fcc5207ba board: ti: dra7xx: add FIT image TEE processing
Populate the corresponding TEE image processing call to be
performed during FIT loadable processing.

Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:22 -05:00
Lokesh Vutla
71c1b58e89 ARM: DRA7: Make FIT boot as default boot on HS devices
Verification has to be done before booting any images on HS devices. So
default the boot to FIT on HS devices.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-03 13:21:08 -05:00
Mugunthan V N
1053a769fb board: ti: dra7xx: complex definitions should be protected with parentheses
As a standard practice complex definitions should be protected
with parentheses, as it might fail when used in a complex if
statements.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-08 09:33:35 -04:00
Mugunthan V N
e8131386dc ARM: dts: dra72: add rev C evm support
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.

Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-08 09:33:35 -04:00
Andreas Dannenberg
17c2987336 arm: omap5: add U-Boot FIT signing and SPL image post-processing
Modify the SPL build procedure for AM57xx and DRA7xx high-security (HS)
device variants to create a secure u-boot_HS.img FIT blob that contains
U-Boot and DTB artifacts signed with a TI-specific process based on the
CONFIG_TI_SECURE_DEVICE config option and the externally-provided image
signing tool.

Also populate the corresponding FIT image post processing call to be
performed during SPL runtime.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-07-14 18:22:22 -04:00
Lokesh Vutla
df6b506f16 ti_omap5_common: Find right dtb file for DRA72-RevC Evm
DRA72-Evm revC uses dra72-evm-revc.dtb. Update the same in env vatiables.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-07-01 17:42:57 -04:00
Keerthy
1428d83270 arm: dra7xx: Assign omap_vcores based on board type
Currently omap_vcores which holds pmic data is being assigned based
on the SoC type. PMIC is not a part of SoC. It is logical to
to assign omap_vcores based on board type. Hence over ride the
vcores_init function and assign omap_vcores based on the board type.

Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
2016-06-12 13:14:57 -04:00
Lokesh Vutla
09da87dafd board: dra7: fit: add support for selecting dtb dynamically
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-05-27 15:47:43 -04:00
Daniel Allred
62a09f0535 ARM: omap5: add ft_board_setup for dra7xx/am57xx
Adds the board specific ft_board_setup() functions that
are called when CONFIG_OF_BOARD_SETUP is defined. These functions
will currently just call the ft_cpu_setup() function.

Adds CONFIG_OF_BOARD_SETUP to the defconfig files
for dra72_evm, dra74_evm, and am57xx_evm.

Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>

Reviewed-by: Tom Rini <trini@konsulko.com>
2016-05-27 15:41:38 -04:00
Dan Murphy
39fbac91e1 board: ti: DRA7: Add DP83867 TI phy for rev c
Enable the TI DP83867 Giga bit phy on the
dra7 rev c board.  The rx and tx internal
delays are need for this board so the usage
of RGMII_ID is required.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-04-01 17:18:07 -04:00
Nishanth Menon
8cac14719d board: ti: DRA7: Add DRA72-rev C evm pinmux
Add the pinmux data for rev C evm. This is different from previous
revisions of the platform thanks to the deltas introduced both from
silicon side and from SoC side.

Based on J6EcoES2_EVM_Base_Config-20160309b and PCT-DRA72x-v1.3.0.7 for
SR2.0 silicon.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:16 -04:00
Ravi Babu
6b1c14bb67 board: ti: DRA72: revC evm: Update sdram timing configuration for SR2.0
DDR configuration has changes from SR1.1 based Rev-A/B version of evm
to the SR2.0 based Rev C of the EVM. Rev C evm now uses the higher
density MT41K512M8RH-125-AAT:E (IT) which is of size 2GB.

Update the DDR configuration based on data from EMIF configuration
tool 1.1.1. NOTE: we use eeprom information (ram_size) to update the
configuration.

Tested-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:14 -04:00
Paul Kocialkowski
3ef56e61c8 omap-common: Rename set_muxconf_regs_essential to set_muxconf_regs
There is no distinction between essential and non-essential mux configuration,
so it doesn't make sense to have an "essential" prefix.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
2016-03-15 15:12:06 -04:00
Lokesh Vutla
26eccf31b3 ARM: DRA72-evm: Update mux and VIRTUAL/MANUAL mode timings
All the mux configurations needs to be done as part of the IODelay
sequence to avoid glitch. Adding all the mux configuration, MANUAL/VIRTUAL
mode configuration as needed for DRA72-evm.

Also update the mux for SD card detect on DRA74-evm.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:52 -04:00
Lokesh Vutla
d468b1781a ARM: DRA7-evm: Update memory info in banks
Updating the memory banks properly so that DT is populated accordingly.
And updating this only after DDR is properly detected by eeprom, so that
git bisect is still maintained.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:51 -04:00
Lokesh Vutla
c4a2736ca1 ARM: DRA7: EMIF: Add 4GB DDR settings
The REVH and later versions of DRA7-evm uses MICRON MT41K512M16HA-125 memory
chips which is of size 4GB(2GB on EMIF1 and 2GB on EMIF2). Add support for the
same.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:51 -04:00
Lokesh Vutla
a7638833b3 ARM: DRA7: Move emif settings to board specific files
The newer versions of DRA7 boards has EEPROM populated with DDR
size specified in it. Moving DRA7 specific emif related settings
to board files so that emif settings can be identified based on EEPROM.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:50 -04:00
Lokesh Vutla
25afe55de5 ARM: DRA7: Enable EEPROM support
Enable EEPROM support for DRA74-evm.

Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-03-14 19:18:50 -04:00
Paul Kocialkowski
07815eb9f3 omap-common: Common serial and usbethaddr functions based on die id
Now that we have a common prototype to grab the omap die id, functions to figure
out a serial number and usb ethernet address can use it directly.
Those also get an omap_die_id prefix for better consistency.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:22 -04:00
Paul Kocialkowski
9fd5401659 omap5: omap_die_id support
This introduces omap5 support for omap_die_id, which matches the common
omap_die_id definition. It replaces board-specific code to grab the die id bits.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-22 14:17:21 -04:00
Kishon Vijay Abraham I
6f1af1e358 board: ti: invoke clock API to enable and disable clocks
invoke enable_usb_clocks during board_usb_init and disable_usb_clocks
during board_usb_exit to enable and disable clocks respectively.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:22 -04:00
Kishon Vijay Abraham I
03c128c949 board: ti: remove duplicate initialization of vbus_id_status
vbus_id_status is initialized in board_usb_init. So remove it
while creating dwc3_device objects.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:20 -04:00
Nishanth Menon
76cff2b108 ARM: DRA74-evm: Use SMA_1 spare register to workaround DP83865 phy on SR2.0
DP83865 ethernet phy used on DRA74x-evm is quirky and the datasheet
provided IODELAY values for standard RGMII phys do not work.

Silicon Revision(SR) 2.0 provides an alternative bit configuration
that allows us to do a "gross adjustment" to launch the data off a
different internal clock edge. Manual IO Delay overrides are still
necessary to fine tune the clock-to-data delays. This is a necessary
workaround for the quirky ethernet Phy we have on the platform.

NOTE: SMA registers are spare "kitchen sink" registers that does
contain bits for other workaround as necessary as well. Hence the
control for the same is introduced in a generic SoC specific, board
generic location.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:13 -04:00
Nishanth Menon
0358923409 ARM: DRA74-evm: Add iodelay values for SR2.0
Silicon revision 2.0 has new signal routing hence has an updated set of
iodelay parameters to be used. Update the configuration for the same.
Padmux remains the same.

Based on data from VayuES2_EVM_Base_Config-20150807.

NOTE: With respect to the RGMII values, the Manual IODelay values
are used for the fine adjusments needed to meet the tight RGMII
specification.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:13 -04:00