Commit graph

8 commits

Author SHA1 Message Date
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
SRICHARAN R
1a89a217f5 ARM: OMAP4/5: Move USB pads to essential list.
USB module pads are getting enabled under non-essential
group. These will be required for fastboot, tftp support.
So move this to essential list to have them working when
non-essential pads are no more muxed.

Signed-off-by: R Sricharan <r.sricharan@ti.com>
2012-07-07 14:07:36 +02:00
Nishanth Menon
3acb553439 OMAP4460: TPS Ensure SET1 is selected after voltage configuration
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
                           |---------------| (SET1 default 1.4V)
                           |               --------(programmed voltage)
                           | <- (This switch happens on mux7,pullup)
vdd_mpu(TPS)         -----/ (OPP boot voltage)
                                             --------- (programmed voltage)
vdd_core(TWL6030)    -----------------------/ (OPP boot voltage)
Problem 1)                |<----- Tx ------>|
   timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.

By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
                                  -------- (programmed voltage)
vdd_mpu(TPS)         ------------/ (Opp boot voltage)
                                   --------- (programmed voltage)
vdd_core(TWL6030)    -------------/ (OPP boot voltage)

NOTE: This does not attempt to address OMAP5 - Aneesh please confirm

Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2012-05-15 08:31:22 +02:00
Aneesh V
cd5847ac3a omap4460: fix TPS initialization
TPS power IC is controlled using a GPIO (gpio_wk7).
This GPIO should be maintained at logic 1 always. As
such an internal pull-up on this pin will do the job,
driving the GPIO outuput is not needed. This will avoid
the need of using GPIO library in SPL and also may
save some power.

Signed-off-by: Aneesh V <aneesh@ti.com>
2011-12-06 23:59:34 +01:00
Sricharan
78f455c055 omap4/5: Add support for booting with CH.
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.

Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Sricharan
508a58fa8e omap5: Add minimal support for omap5430.
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.

OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.

Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.

Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-11-15 22:25:50 +01:00
Aneesh V
43de24fdc7 omap4: fix pad configuration settings for SDP and Panda
omap4: fix pad configuration settings for SDP and Panda

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sebastien Jan <s-jan@ti.com>
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-13 08:25:16 +02:00
Aneesh V
469ec1e353 omap4: cleanup pin mux data
- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
  to SoC directory). Will help in having single SPL for all
  boards.
- Non-essential part(the pins not essential for u-boot to function)
  need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-08-03 12:49:19 +02:00
Renamed from board/ti/panda/panda.h (Browse further)