Commit graph

213 commits

Author SHA1 Message Date
Simon Glass
cd93d625fd common: Drop linux/bitops.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
c05ed00afb common: Drop linux/delay.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
f7ae49fc4f common: Drop log.h from common header
Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:18 -04:00
Simon Glass
691d719db7 common: Drop init.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Simon Glass
90526e9fba common: Drop net.h from common header
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:31 -04:00
Florinel Iordache
5d3bcdb12f phy: add support for backplane kr mode
Add generic support for backplane kr modes currently available:
10gbase-kr, 40gbase-kr4. Remove platform generic fixups
(armv8/layerscape and powerpc) for ethernet interfaces specified
in device tree as supported backplane modes.

Signed-off-by: Florinel Iordache <florinel.iordache@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-20 13:35:11 +05:30
Simon Glass
db41d65a97 common: Move hang() to the same header as panic()
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.

Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-17 17:53:40 -05:00
Simon Glass
b5981474f1 common: Move some CPU functions out of common.h
These functions belong in cpu_func.h since they do not use driver model.
Move them over. Don't bother adding comments since these functions should
be deleted.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:13 -05:00
Simon Glass
6887c5bed9 common: Move some time functions out of common.h
These functions belong in time.h so move them over and add comments.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:11 -05:00
Udit Agarwal
bef1845404 freescale/powerpc: Rename the config CONFIG_SECURE_BOOT name
Rename the CONFIG_SECURE_BOOT name to CONFIG_NXP_ESBC to avoid
conflicts with UEFI secure boot.

Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-08 16:32:08 +05:30
Mario Six
5c22998503 mpc83xx: Use pre-defined asm functions
For a lot of inline assembly calls in the mpc8xxx and mpc83xx
directories, we already have convenient pre-defined helper functions,
but they're not used, resulting in hard-to-read code.

Use these helper functions where ever possible and useful.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21 07:52:34 +02:00
Mario Six
fe7d654d04 mpc83xx: Migrate CONFIG_SYS_{BR, OR}*_PRELIM to Kconfig
Migrate the BR/OR settings to Kconfig. These must be known at compile
time, so cannot be configured via DT.

Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
2019-05-21 07:52:33 +02:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Masahiro Yamada
b08c8c4870 libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05 10:16:28 -05:00
Simon Glass
cbcbf71bf2 powerpc: Drop probecpu() in favour of arch_cpu_init()
To avoid an unnecessary arch-specific call in board_init_f(), rename this
function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-25 17:38:41 -05:00
Masahiro Yamada
1221ce459d treewide: replace #include <asm/errno.h> with <linux/errno.h>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content.  (both just wrap <asm-generic/errno.h>)

Replace all include directives for <asm/errno.h> with <linux/errno.h>.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-09-23 17:55:42 -04:00
Sumit Garg
8f01397ba7 powerpc/mpc85xx: SECURE BOOT- Enable chain of trust in SPL
As part of Chain of Trust for Secure boot, the SPL U-Boot will validate
the next level U-boot image. Add a new function spl_validate_uboot to
perform the validation.

Enable hardware crypto operations in SPL using SEC block.
In case of Secure Boot, PAMU is not bypassed. For allowing SEC block
access to CPC configured as SRAM, configure PAMU.

Reviewed-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-21 11:09:23 -07:00
Aneesh Bansal
f698e9f39a powerpc/SECURE_BOOT: Add PAMU driver
PAMU driver basic support for usage in Secure Boot.
In secure boot PAMU is not in bypass mode. Hence to use
any peripheral (SEC Job ring in our case), PAMU has to be
configured.

The patch reverts commit 7cad2e38d6.

The Header file pamu.h and few functions in driver have been derived
from Freescale Libos.

Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-24 08:40:55 -08:00
Ashish kumar
43381474ff arch/powperpc: Fix start_align due to use of __ffs64() instead ffs64()
Incorrect DDR law was created in case of B4860qds after commit
2d2f490d. Return value of ffs64() differs from __ffs64(), eg.
    ffs64(0x80000000) = 0x20
    __ffs64(0x80000000) = 0x1f
As a result of this change, callers need to adjust the expected
return value by removing -1.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 12:30:31 -08:00
Tom Rini
5b8031ccb4 Add more SPDX-License-Identifier tags
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously.  Convert all of these to the correct SPDX-License-Identifier
tag.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-19 08:31:21 -05:00
Tom Rini
da58dec866 Various Makefiles: Add SPDX-License-Identifier tags
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one.  This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.

Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-11-10 09:19:52 -05:00
Fabio Estevam
2d2f490dd5 powerpc: Remove __ilog2_u64 and ffs4 from bitops
Remove __ilog2_u64 and ffs4 from powerpc bitops to align with the
kernel implementation.

Use the generic __ffs64 instead of a custom powerpc implementation.

Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-11-05 16:47:05 -05:00
Shaveta Leekha
b8bf0adc12 powerpc/mpc85xx: Add DSP side awareness for Freescale Heterogeneous SoCs
The code provides framework for heterogeneous multicore chips based on StarCore
and Power Architecture which are chasis-2 compliant, like B4860 and B4420

It will make u-boot recognize all non-ppc cores and peripherals like
SC3900/DSP CPUs, MAPLE, CPRI and print their configuration in u-boot logs.
Example boot logs of B4860QDS:

U-Boot 2015.01-00232-geef6e36-dirty (Jan 19 2015 - 11:58:45)

CPU0:  B4860E, Version: 2.2, (0x86880022)
Core:  e6500, Version: 2.0, (0x80400120)
Clock Configuration:
       CPU0:1600 MHz, CPU1:1600 MHz, CPU2:1600 MHz, CPU3:1600 MHz,
       DSP CPU0:1200 MHz, DSP CPU1:1200 MHz, DSP CPU2:1200 MHz, DSP CPU3:1200 MHz,
       DSP CPU4:1200 MHz, DSP CPU5:1200 MHz,
       CCB:666.667 MHz,
       DDR:933.333 MHz (1866.667 MT/s data rate) (Asynchronous), IFC:166.667 MHz
       CPRI:600  MHz
       MAPLE:600  MHz, MAPLE-ULB:800  MHz, MAPLE-eTVPE:1000 MHz
       FMAN1: 666.667 MHz
       QMAN:  333.333 MHz

Top level changes include:
(1) Top level CONFIG to identify HETEROGENUOUS clusters
(2) CONFIGS for SC3900/DSP components
(3) Global structures like "cpu_type" and "MPC85xx_SYS_INFO"
    updated for dsp cores and other components
(3) APIs to get DSP num cores and their Mask like:
        cpu_dsp_mask, cpu_num_dspcores etc same as that of PowerPC
(5) Code to fetch and print SC cores and other heterogenous
    device's frequencies
(6) README added for the same

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-03-04 10:15:29 -08:00
Ruchika Gupta
0181937fa3 crypto/fsl: Add fixup for crypto node
Era property is added in the crypto node in device tree.
Move the code to do so from arch/powerpc/mpc8xxx/fdt.c to
drivers/sec/sec.c so that it can be used across arm and
powerpc platforms having crypto node.

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
[York Sun: Fix commit message indentation]
Reviewed-by: York Sun <yorksun@freescale.com>
2015-01-23 22:29:14 -06:00
Codrin Ciubotariu
7e40e4beb8 arch/powerpc: Initialize VSC9953 L2 Switch
This patch initializes VSC9953 L2 Switch for boards that have
CONFIG_VSC9953 defined in their config file.

Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
2015-01-21 09:23:35 -06:00
Nikhil Badola
a1c04e2785 drivers: usb: Make usb device-tree fixup code architecture independent
move usb device tree fixup code from "arch/powerpc/" to "drivers/usb/"
so that it works independent of architecture it is running on

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:40:50 -08:00
Shengzhou Liu
f605079041 powerpc/mpc85xx: Add T1024/T1023 SoC support
Add support for Freescale T1024/T1023 SoC.

The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
  - Three PCI Express 2.0 controllers
- Additional peripheral interfaces
  - One SATA 2.0 controller
  - Two USB 2.0 controllers with integrated PHY
  - Enhanced secure digital host controller (SD/eSDHC/eMMC)
  - Enhanced serial peripheral interface (eSPI)
  - Four I2C controllers
  - Four 2-pin UARTs or two 4-pin UARTs
  - Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0

Differences between T1024 and T1023:
  Feature         T1024  T1023
  QUICC Engine:   yes    no
  DIU:            yes    no
  Deep Sleep:     yes    no
  I2C controller: 4      3
  DDR:            64-bit 32-bit
  IFC:            32-bit 28-bit

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:14 -08:00
Ruchika Gupta
028dbb8db1 fsl_sec : Change accessor function to take care of endianness
SEC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of SEC IP.

So update acessor functions with common SEC acessor functions to take care
both type of endianness.

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-10-16 14:16:50 -07:00
ramneek mehresh
e628c8f75d powerpc/8xxx: Fix in USB device-tree fixup
Fix following issues in USB device-tree fixup:
        - returns when either dr_mode or phy_type not defined.
          This was terminating fix-up when only either property
          was defined in hwconfig string
        - updates dr_mode_type or dr_phy_type with junk value when
          their index is -1. Now these are updated only when their
          respective index is pointing to relevant types
          in modes[] and phys[] array
        - dr_mode_type and dr_phy_type were not NULL for
          each controller

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-09-24 13:05:51 -07:00
Sandeep Singh
d43a386a91 powerpc/mpc85xx: Removed support for G4060
G4060 has no PA cores, hence removing its support.

Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:54 -07:00
Shaveta Leekha
9c3fdd883a powerpc/mpc85xx: Added B4460 support
B4460 differs from B4860 only in number of CPU cores,
hence used existing support for B4860.
B4460 has 2 PPC cores whereas B4860 has 4 PPC cores.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:24:26 -05:00
Alexander Graf
b539534d12 PPC 85xx QEMU: Always assume 1 core
We only need u-boot to bother about a single core in the QEMU machine.
Everything that would require additional knowledge of more cores gets
handled by QEMU and passed straight into the payload we execute.

Because of this setup, it would be counterproductive to enable SMP support
in u-boot. We would have to rip CPUs out of already existing spin tables
and respin them from u-boot. It would be a pretty big mess.

So only assume we have a single core. This fixes errors about CONFIG_MP
being disabled.

Signed-off-by: Alexander Graf <agraf@suse.de>
2014-05-13 08:26:55 -07:00
Shengzhou Liu
5122dfae5d powerpc/85xx: add T4080 SoC support
The T4080 SoC is a low-power version of the T4160.
T4080 combines 4 dual-threaded Power Architecture e6500
cores with single cluster and two memory complexes.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-05-13 08:26:54 -07:00
Prabhakar Kushwaha
6b3d588efe powerpc/mpc85xx:Disable non DDR LAWs before init_law
Before parsing LAW table i.e. init_law, boot loader should disable all
previous LAWs except DDR LAWs which has been created by previous
pre boot loader during DDR initialization.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:50 -07:00
Aneesh Bansal
7efb4b5197 powerpc/mpc8xxx: SECURE BOOT- Disable law 0 for non PBL platforms
ISBC creates a LAW 0 entry for non PBL platforms, which is not
disabled before transferring the control to uboot.
The LAW 0 entry has to be disabled.

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:46 -07:00
Masahiro Yamada
e8a8b8246a Makefile: Select objects by CONFIG_ rather than $(ARCH) or $(CPU)
Convert like follows:

 CPU mpc83xx  -> CONFIG_MPC83xx
 CPU mpc85xx  -> CONFIG_MPC85xx
 CPU mpc86xx  -> CONFIG_MPC86xx
 CPU mpc5xxx  -> CONFIG_MPC5xxx
 CPU mpc8xx   -> CONFIG_8xx
 CPU mpc8260  -> CONFIG_8260
 CPU ppc4xx   -> CONFIG_4xx
 CPU x86      -> CONFIG_X86
 ARCH x86     -> CONFIG_X86
 ARCH powerpc -> CONFIG_PPC

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-12-16 08:59:42 -05:00
Shengzhou Liu
629d6b32d6 powerpc/mpc85xx: Add T2080/T2081 SoC support
Add support for Freescale T2080/T2081 SoC.

T2080 includes the following functions and features:
- Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs)
- High-speed peripheral interfaces
  - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
  - Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
  - Two serial ATA (SATA 2.0) controllers
  - Two high-speed USB 2.0 controllers with integrated PHY
  - Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
  - Enhanced serial peripheral interface (eSPI)
  - Four I2C controllers
  - Four 2-pin UARTs or two 4-pin UARTs
  - Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0

Differences between T2080 and T2081:
  Feature               T2080 T2081
  1G Ethernet numbers:  8     6
  10G Ethernet numbers: 4     2
  SerDes lanes:         16    8
  Serial RapidIO,RMan:  2     no
  SATA Controller:      2     no
  Aurora:               yes   no
  SoC Package:          896-pins 780-pins

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-11-25 11:44:25 -08:00
York Sun
0b66513b27 Driver/IFC: Move Freescale IFC driver to a common driver
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25 11:43:47 -08:00
York Sun
5614e71b49 Driver/DDR: Moving Freescale DDR driver to a common driver
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25 11:43:43 -08:00
Masahiro Yamada
c54ecaa965 powerpc: move mpc8xxx entry under arch/powerpc/cpu/
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2013-11-17 14:11:31 -05:00
Masahiro Yamada
06c14117c4 powerpc: convert makefiles to Kbuild style
Note:
arch/powerpc/cpu/mpc8260/Makefile is originally like follows:

    ---<snip>---
    START   = start.o kgdb.o
    COBJS   = traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \
    ---<snip>---
    COBJS-$(CONFIG_ETHER_ON_SCC) = ether_scc.o
    ---<snip>---
    $(LIB): $(OBJS)
            $(call cmd_link_o_target, $(OBJS) $(obj)kgdb.o)

The link rule `$(call cmd_link_o_target, $(OBJS) $(obj)kgdb.o)'
is weird.
kbdg.o is not included in $(OBJS) but linked into $(LIB)
and $(LIB) is not dependent on kgdb.o.
(Broken dependency tracking)

So,
    START   = start.o kgdb.o
shoud have been
    START   = start.o
    SOBJS   = kgdb.o

That is why this commit adds kgdb.o to obj-y, not to extra-y.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
2013-10-31 13:26:44 -04:00
Valentin Longchamp
7e157b0ade mpc8xxx: set x2 DDR3 refresh rate if SPD config requires it
If the DDR3 module supports industrial temperature range and requires
the x2 refresh rate for that temp range, the refresh period must be
3.9us instead of 7.8 us.

This was successfuly tested on kmp204x board with some MT41K128M16 DDR3
RAM chips (no module used, chips directly soldered on board with an SPD
EEPROM).

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix minor conflicts in fsl_ddr_dimm_params.h,
	   lc_common_dimm_params.c, common_timing_params.h]
Acked-by: York Sun <yorksun@freescale.com>
2013-10-24 09:35:52 -07:00
Valentin Longchamp
0778bbe2d4 mpc8xxx: call i2c_set_bus_num in __get_spd
This is necessary with the new I2C subystem that was introduced lately.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
2013-10-24 09:35:46 -07:00
ramneek mehresh
f1810d851c powerpc/usb:Define CONFIG_USB_MAX_CONTROLLER_COUNT for all 85xx socs
CONFIG_USB_MAX_CONTROLLER_COUNT macro recently defined for
initializing all USB controllers on a given platform. This
macro is defined for all 85xx socs

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
2013-10-24 09:35:03 -07:00
Priyanka Jain
0dd38a35f4 powerpc: Fix CamelCase warnings in DDR related code
Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h
has various parameters with embedded acronyms capitalized that trigger the CamelCase
warning in checkpatch.pl

Convert those variable names to smallcase naming convention and modify all files
which are using these structures with modified structures.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
2013-10-16 16:15:16 -07:00
Shruti Kanetkar
2f848f97d7 powerpc: Use print_size() where appropriate
Makes the startup output more consistent

Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-20 10:37:58 -07:00
Ying Zhang
bb0dc1084f powerpc: mpc85xx: Support booting from SD Card with SPL
The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.

The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
	* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
	ddr spd code can get the interleaving mode setting in env. It loads
	final uboot image from offset 96KB.
	* final uboot image, size is variable depends on the functions enabled.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-20 09:47:26 -07:00
Ying Zhang
0151d99d74 powerpc: deleted unused symbol CONFIG_SPL_NAND_MINIMAL and enabled some functionality for common SPL
1. The symbol CONFIG_SPL_NAND_MINIMAL is unused, so deleted it.
2. Some functions were unused in the minimal SPL, but it is useful
in the common SPL. So, enabled some functionality for common SPL.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-20 09:47:15 -07:00
ramneek mehresh
61033367a0 powerpc/usb: Depricate usb_phy_type and usb_dr_mode uboot env variables
Remove getting values of usb mode and phy_type from "usb_dr_mode"
and "usb_phy_type" uboot env variables. Now, these are determined
only from hwconfig string

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-14 10:58:21 -07:00
James Yang
c45f5c08b7 powerpc/mpc8xxx: Fix TIMING_CFG_3[EXT_ACTTOPRE]
The TIMING_CFG_3[EXT_ACTTOPRE] register field is 2 bits wide, but
the mask omitted the LSB.  This patch provides a 2-bit wide mask.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09 12:43:32 -07:00