Commit graph

17 commits

Author SHA1 Message Date
Peng Fan
6aead23323 imx: imx8qm/qxp: Recover SPL data section for partition reboot
When doing partition reboot, the boot image won't be reloaded by ROM,
it is just CPU reset to boot entry. The SW has to keep the boot image
inside the RAM unchanged. It includes both the TEXT section and DATA
section.

For SPL, the problem is DATA section will be updated at runtime, so in
next partition reboot the data is not same as the initial value from
cold boot. If any code depends on the initial value, then it will have
problem.

This patch introduces a mechanism to recover the data section
for partition reboot. It adds a new section in image for saving
data section. When from cold boot, the data section will be saved
to that new section at SPL early phase. When from partition reboot,
the data section will be restored from the new section.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Peng Fan
f44afd546f imx: imx8qm/qxp: reserving DDR memory for M4
The DDR memory from 0x88000000 to 0x8FFFFFFF is assigned to M4 on
QM and QXP. The M4 can allocate this memory by two ways,
in SCD or u-boot.

In this patch, u-boot addes the memory reserve node to DTB to pass
the info to kernel, no matter the M4 memory is reserved in SCD
or u-boot. So kernel won't access M4 reserved memory.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-10 20:55:20 +02:00
Franck LENORMAND
242d1cd69b imx8: Configure SNVS
Add a module to configure the tamper and secure violation of
the SNVS using the SCU API.

The module also adds some commands:
 - snvs_cfg: Configure the SNVS HP and LP registers
 - snvs_dgo_cfg: Configure the SNVS DGO bloc if present (8QXP)
 - tamper_pin_cfg: Change the configuration of the tamper pins
 - snvs_clear_status: Allow to write to LPSR and LPTDSR to clear
   status bits

Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-05-01 13:46:22 +02:00
Anatolij Gustschin
eb79cafea2 imx: add imx8x based deneb board
Add support for Capricorn Deneb SoM variant.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2020-01-14 22:15:21 +01:00
Anatolij Gustschin
7b5b934313 imx: add imx8x capricorn giedi board
Add support for i.MX8X based Capricorn Giedi SoM.

Supported interfaces: GPIO, ENET, eMMC, I2C, UART.

Console output:

  U-Boot SPL 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100)
  Trying to boot from MMC1
  Load image from MMC/SD 0x3e400

  U-Boot 2020.01-00003-gfd1c98f (Jan 07 2020 - 15:51:25 +0100) ##v01.07

  CPU:   NXP i.MX8QXP RevB A35 at 1200 MHz at 30C

  Model: Siemens Giedi
  Board: Capricorn
  Boot:  MMC0
  DRAM:  1022 MiB
  MMC:   FSL_SDHC: 0
  Loading Environment from MMC... OK
  In:    serial@5a080000
  Out:   serial@5a080000
  Err:   serial@5a080000
  Net:   eth1: ethernet@5b050000 [PRIME]
  Autobooting in 1 seconds, press "<Esc><Esc>" to stop

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2020-01-14 22:15:21 +01:00
Oliver Graute
eef72440db imx: support i.MX8QM ROM 7720 a1 board
Add i.MX8QM ROM 7720a1 board support

Boot log as below:
U-Boot 2019.10-rc3-00004-gd073e0242f (Sep 20 2019 - 08:24:13 +0200)

CPU:   NXP i.MX8QM RevB A53 at 1200 MHz

Model: Advantech iMX8QM Qseven series
Board: ROM-7720-A1 4GB
Build: SCFW 65afe5f6
Boot:  SD2
DRAM:  4 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial@5a060000
Out:   serial@5a060000
Err:   serial@5a060000
Net:   eth0: ethernet@5b040000Could not get PHY for FEC1: addr 1
, eth-1: ethernet@5b050000
Hit any key to stop autoboot:  0

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
2019-11-03 21:18:00 +01:00
Peng Fan
7e2db74231 imx8: Add AHAB secure boot support
Add function and new command "auth_cntr" for secure boot support.
When booting with life cycle set to OEM closed, we need to use
this function to authenticate the OS container and load kernel & FDT
from OS container to their destination.

Also add image authentication call when loading container images.

Users can set CONFIG_AHAB_BOOT=y to enable the feature. It is not
set at default.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-11-03 17:04:16 +01:00
Peng Fan
700315c9ac imx: add container target
To support SPL loading container file, add a new Makefile target,
and introduce a new Kconfig file to source the cfg file which
will be parsed by mkimage.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:58 +02:00
Peng Fan
7b86cd4274 imx8: support parsing i.MX8 Container file
Add parsing i.MX8 Container file support, this is to let
SPL could load images in a container file to destination address.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:58 +02:00
Marcel Ziswiler
3d60366500 board: toradex: add apalis imx8qm 4gb wb it v1.0b module support
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.

Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C

Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-06-11 10:42:48 +02:00
Marcel Ziswiler
7ce134b7c3 board: toradex: add colibri imx8qxp 2gb wb it v1.0b module support
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.

Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C

Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-06-11 10:42:48 +02:00
Peng Fan
0d331c035a imx: support i.MX8QM MEK board
Add i.MX8QM MEK board support.
Included a basic dts, enabled SPL FIT

Boot log as below:
U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
Normal Boot
Trying to boot from MMC2_2

U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)

CPU:   NXP i.MX8QM RevB A53 at 142933 MHz

Model: Freescale i.MX8QM MEK
Board: iMX8QM MEK
Build: SCFW 9330215b
Boot:  SD1
DRAM:  6 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial@5a060000
Out:   serial@5a060000
Err:   serial@5a060000
Net:
Error: ethernet@5b040000 address not set.
eth-1: ethernet@5b040000
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25 17:03:25 +02:00
Peng Fan
7f50af6090 imx8: add cpu support
Add cpu type and Kconfig entry

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25 17:03:25 +02:00
Peng Fan
04b249656e imx8: scu: use dedicated MU for SPL
SPL runs in EL3 mode, except MU0_A, others are not powered on,
and could not be used. However normal U-Boot use MU1_A, so we
could not reuse the one in dts. And we could not replace the one
in dts with MU0_A, because MU0_A is reserved in secure world.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28 20:35:47 +01:00
Peng Fan
3bd888b55e imx8qxp: add SUPPORT_SPL option
Enable SUPPORT_SPL option for i.MX8QXP, then we could enable SPL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-01-28 20:35:47 +01:00
Peng Fan
d0dd73974c imx: add i.MX8QXP MEK board support
Add i.MX8QXP MEK board support
Enabled pinctrl/clk/power-domain/mmc/i2c/fec driver.
Added README file.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-10-22 13:00:09 +02:00
Peng Fan
b2b8b9be2f imx: add Kconfig entry for i.MX8QXP
Add Kconfig entry for i.MX8QXP

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 12:59:01 +02:00