Commit graph

62 commits

Author SHA1 Message Date
Matt Porter
f485c8a35b phy: add support for ET1011C phys
Adds an ET1011C PHY driver which is derived from the
Linux kernel PHY driver (drivers/net/phy/et1011c.c)
from the v3.9-rc2 tag. Note that an errata workaround
config option is implemented to allow for TX_CLK to be
enabled even when gigabit mode is negotiated. This
workaround is used on the PG1.0 TI814X EVM.

Signed-off-by: Matt Porter <mporter@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-05-10 08:25:54 -04:00
Troy Kisky
1adb406b01 phy: add phy_find_by_mask/phy_connect_dev
It is useful to be able to try a range of
possible phy addresses to connect.

Also, an ethernet device is not required
to use phy_find_by_mask leading to better
separation of mii vs ethernet, as suggested
by Andy Fleming.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Kim Phillips
960d70c600 drivers/net/: sparse fixes
phy.c:46:5: warning: symbol 'genphy_config_advert' was not declared. Should it be static?
phy.c:121:5: warning: symbol 'genphy_setup_forced' was not declared. Should it be static?
phy.c:468:5: warning: symbol 'phy_probe' was not declared. Should it be static?
phy.c:491:19: warning: symbol 'get_phy_driver' was not declared. Should it be static?
phy.c:508:19: warning: symbol 'phy_device_create' was not declared. Should it be static?
phy.c:552:5: warning: symbol 'get_phy_id' was not declared. Should it be static?
phy.c:584:19: warning: symbol 'get_phy_device' was not declared. Should it be sta
vitesse.c:126:5: warning: symbol 'vsc8601_config' was not declared. Should it be static?
vsc7385.c:33:5: warning: symbol 'vsc7385_upload_firmware' was not declared. Should it be static?
tgec_phy.c:33:5: warning: symbol 'tgec_mdio_write' was not declared. Should it be static?
tgec_phy.c:75:5: warning: symbol 'tgec_mdio_read' was not declared. Should it be static?
tgec_phy.c:117:5: warning: symbol 'tgec_mdio_reset' was not declared. Should it be static?
eth.c:48:6: warning: symbol 'dtsec_configure_serdes' was not declared. Should it be static?
p4080.c:26:5: warning: symbol 'port_to_devdisr' was not declared. Should it be static?

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04 11:00:36 -07:00
Timur Tabi
6e5b9ac097 phylib: phy_startup() should return an error code on failure
phy_startup() calls the PHY driver's startup function, but it ignores the
return code from that function, and so it never returns any failures.

Signed-off-by: Timur Tabi <timur@freescale.com>
2012-07-11 13:15:30 -05:00
Troy Kisky
9fafe7dab9 net: phy: make board_phy_config responsible for calling drv->config
Boards may have things they want done before or after normal phy config.
Letting the boards call drv->config allows them more flexibilty.
Boards affected by this change are corenet_ds and mpc8544ds.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2012-02-27 21:19:25 +01:00
Nobuhiro Iwamatsu
5751aa2f24 phy: Add support for SMSC LAN87xx PHYs
This adds support for the SMSC LAN87xx PHYs.

Following PHYs can be used by set CONFIG_PHY_SMSC to config.
 - SMSC LAN8700
 - SMSC LAN8710/LAN8720
 - SMSC LAN8710/LAN8720

A setup of PHY was copied from linux kenrel.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Fixed white space errors; modified commit message a bit.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-12-05 23:07:59 +01:00
Wolfgang Denk
0dcfb0fcb8 Revert "phylib: remove a couple of redundant code lines"
This reverts commit 041c542219.

The lines removed by this commit weren't redundant. The logic is (and
probably should be better commented):

Find the intersection of the advertised capabilities of both sides of
the link (lpa).
From that intersection, find the highest capability we can run at
(that will be the negotiated link).

Now imagine that the intersection (lpa) is (LPA_100HALF | LPA_10FULL).

The code will now set phydev->speed to 100, and phydev->duplex to 1,
but this link does not support 100FULL.

Kudos to Andy Fleming <afleming@gmail.com> for binging this to
attention and for the explanation.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-28 21:02:43 +02:00
Vladimir Zapolskiy
041c542219 phylib: remove a couple of redundant code lines
This change slightly improves readability of the phydev speed/duplex
assignment logic.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-09-10 00:08:26 +02:00
Vladimir Zapolskiy
e3a77218a2 phylib: reset mii bus only if reset handler is registered
This change allows to cope with a mii bus device registered using
miiphy_register(), which doesn't assign a default reset handler.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-09-10 00:07:55 +02:00
Wolfgang Denk
b91a9d9d4d phy.c: make less verbose - turn printf() into debug()
The PHY driver was too verbose and corrupted the boot message display
like this:

	...
	Net:   TSEC0 connected to Marvell 88E1111S
	TSEC1 connected to Marvell 88E1111S
	TSEC0, TSEC1
	...

Turn printf() into debug() so we het the expected output again:

	...
	Net:   TSEC0, TSEC1
	...

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
2011-08-31 22:35:27 +02:00
Andy Fleming
9082eeac5d phylib: Add a bunch of PHY drivers from tsec
The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.

While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible).  Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:34 -05:00
Andy Fleming
5f184715ec Create PHY Lib for U-Boot
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme.  The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support

The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).

The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.

We now have MDIO drivers and PHY drivers

An MDIO driver provides:
read
write
reset

A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed

The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()

Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)

We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.

We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,

we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.

Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
2011-04-20 15:09:19 -05:00