155fa9af95 "spi: mxc: fix sf probe when using mxc_spi" break
spi flash detection on the aristainetos board. Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.
Signed-off-by: Ye.Li <B37916@freescale.com>
Set the CONFIG_MXC_GPT_HCLK configuration in mx6_common.h, so that
24Mhz OSC clock source will be selected for GPT on all MX6 platforms.
Signed-off-by: Ye.Li <B37916@freescale.com>
For MX6SL and MX6SX, the perclk can come from OSC 24Mhz source. Fix
the get_ipg_per_clk function to support it.
Signed-off-by: Ye.Li <B37916@freescale.com>
Introduce a new configuration "CONFIG_MXC_GPT_HCLK". When it is set,
the GPT will select a high frequency clock as clock source.
Otherwise, the GPT will stay to use 32Khz OSC as clock source.
In the implementation, since only the GPT on i.MX6 series provide the
clock source option for 24Mhz OSC. For others (only i.MX5 and i.MX6
compile the driver), if the configuration is set, the perclk will be
selected as clock source.
MX6Q/D Rev 1.0 and MX6SL are special in the implementation, because they
don't have the 24Mhz OSC clock source option, so also select the perclk
for them. For MX6SL, we will set the OSC 24Mhz to perclk in CCM, so
eventually the clock comes from OSC 24Mhz.
Signed-off-by: Ye.Li <B37916@freescale.com>
In system boot chapter of i.MX6 reference manual, the "Image Vector Table"
figure shows the bootdata.start points to the beginning of the destination
memory. It means the bootdata.size should contain the IVT offset part,
but the calculation in imximage tool does not have.
We found this issue when booting from QuadSPI NOR on i.MX6SX. The u-boot
runs into abnormal (crash or stop) after booting. After checked the destination
memory where the image is loaded to, there are hundreds of bytes at
the image end are not loaded into memory. Since there is a 4096 bytes
round in the calculation, for the booting devices using smaller IVT offset,
such as SD and SPI booting, they are not easy to reproduce.
Signed-off-by: Ye.Li <B37916@freescale.com>
The patch below failed to define the variable, so define it
to make it consistent with M53EVK.
commit a428ac914b
Author: Lothar Rubusch <lothar@denx.de>
Date: Thu Jun 26 11:01:29 2014 +0200
ARM: m28evk: Update default environment
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add ECC geometry for NAND which has 2048b pagesize and 112b OOB
size. This is for example Macronix MX30LF2G28AB chip.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch fixes conflict between PHY pins becoming outputs after reset and
imx6 still driving the pins. It also fixes the reset timing as recommended by
the PHY datasheet.
Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
The older 'mr' variant and the generic variant of the
OT1200 differ in some places. As the name suggests the
generic variant supports more boot devices.
In order to be compatible with the 'mr' variant we define
some 'feature' GPIOs. On the 'mr' variant this pads are
not connected so we define their state with the help
of the internal pullups.
On the generic variant this GPIOs are connected and
represent the state of the hardware.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Commit 155fa9af95 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Add support for the 4.3'' Seiko WVGA parallel display.
In order to direct the splash screen to the Seiko display:
=> setenv panel SEIKO-WVGA
=> save
=> reset
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add support for the Kosagi Novena board. Currently supported are:
- I2C busses
- FEC Ethernet
- MMC0, MMC1, Booting from MMC
- SATA
- USB ports
- USB Ethernet
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Nikolay Dimitrov <picmaster@mail.bg>
Reviewed-by: Nikolay Dimitrov <picmaster@mail.bg>
Commit 155fa9af95 changed the way
to define a GPIO line, which can be used to force CS high
across multiple transactions. In order to fix sf detection
change board code to make use of board_spi_cs_gpio(..).
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
HDMI config options can be placed into the common mx6sabre_common.h file to
avoid duplication.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Declare displays[] and display_count in imx-common/video.h to
prevent "Should it be static?" messages when compiling board
files with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Include <asm/bootm.h> to see the prototype for get_board_rev()
and prevent warning "Should it be static?" with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Without preceding declarations, "make C=1" generates
"Should it be static?" warnings for symbols
do_bootm_linux,
boot_prep_vxworks, and
boot_jump_vxworks
Include of bootm.h also identified a signature mismatch
(const on argv[]).
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Currently uboot wrongly uses 25mV / step for dcdc3, this is a copy and paste
error introduced when adding the axp152_mvolt_to_target during review of the
axp152.c driver. This results in u-boot setting Vddr to 2.3V instead of 1.5V.
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
With the introduction of CONFIG_LOCALVERSION support we cannot build
tools without having a config file (as we won't know our PLAIN_VERSION
until then).
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@ti.com>
The SoCDK uses EMAC1, not EMAC0. This patch fixes the issue.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Add MAINTAINERS entry.
Signed-off-by: Pavel Machek <pavel@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Commit 832472 "tools: socfpga: Add socfpga preloader signing
to mkimage" added tools/socfpga.c which relies on htole32,
le32toh and friends. While compiler.h includes these protypes
for linux from endian.h, it doesn't do so for FreeBSD. Hence
include <sys/endian.h> for FreeBSD.
Cc: Marek Vasut <marex@denx.de>
CC: Tom Rini <trini@ti.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Update readme file for Keystone II EVM boards to actual sources.
Also correct some typos. For now the Edison evaluation board is
added, README for K2E is mostly the same, so update README to
contain information also for K2E evm. Rename file to README as
it contains information for all keystone evm boards.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The K2HK and K2E boards support SPL by default, so add
CONFIG_SPL option. Also export CONFIG_ARM, CONFIG_ARCH_KEYSTONE
and TARGET_K2*_EVM options to spl/.config as they are the same.
So now it's convinient to build gph images using only two commands:
make k2hk_evm_defconfig
make u-boot-spi.gph
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
