Legacy eeprom layout represents the revision number syntactically
(i.e. revision 1.00 is written as 0x100). This is inconsistent with
the representation in newer layouts, where it is defined semantically
(i.e. 0x64).
This patch fixes the issue by replacing the syntactic representation
with the semantic one.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Non-legacy layouts have an extended revision field,
but only the first 2 bytes are the PCB revision.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Enable I2C multi-bus support and config I2C muxes for I2C2 and I2C3.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Introduce a __weak misc_init_r function that just runs dieid_num_r().
Remove misc_init_r from cm_t35, mcx, omap3_logic and mt_ventoux as this was
all they did for misc_init_r.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
The reset_net_chip() function has wrong timings for the reset pulse.
This appeared to work until:
0607e2b (ARMV7: OMAP: Write more than 1 byte at a time in i2c_write)
Fix the Ethernet support by introducing right timings.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Switch to the new EEPROM module and fix the problem of MAC address
being read from the wrong offset due to lack of distinction between
EEPROM layouts.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Read revision from EEPROM and pass it to Linux.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Add board specific EEPROM handling module,
read the serial number from the EEPROM and pass it to Linux.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Move #ifdef CONFIG_SMC911X out of board_eth_init() function,
simplify the board_mmc_init() function, and enclose handle_mac_address()
in the CONFIG_SMC911X.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Seems people fixed their files to use libfoo.o, but didn't actually
update the creation targets to use $(cmd_link_o_target). Update the
rest of the Makefile's found with grep.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Switch from the legacy omap3 mmc driver to the new generic omap hsmmc
driver. This patch is based on the work done for Beagle, etc.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
CM-T3730 is exactly the same board as CM-T35, but it has
TI DM3730 SoC onboard and therefore some changes have to take place
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Use CONFIG_OMAP3_MMC in cm-t35 configuration file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
