The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Replace driver internally coded enabling/disabling of the
analog-filter with the DT binding "i2c-analog-filter".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Today all the I2C instance point on the same global
variable stm32_i2c_setup according the compatible: i2c_priv->setup =
pointer to the same driver data.
This patch changes this driver data (stm32f7_setup and stm32mp15_setup)
to a const struct and move the timing struct 'setup' as element of i2c
privdata, initialized in stm32_ofdata_to_platdata() with the driver
configuration data.
This patch solves issues when several I2C instance have not the same
clock source or not the same configuration: each timing setup is saved
is the I2C privdata.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Commit ca1a4c8632 ("mvebu: select boot device at SoC level") made it
unnecessary for the A385 boards to have their own kwbimage.cfg but as
the x530 was in flight at the time it was added with it's own
kwbimage.cfg. Remove the custom kwbimage.cfg as the SoC level file is
suitable.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Since the CP1 pinctrl is not properly set in the DTS, there is no
need for setting the pinctrl by writing hardcoded values to the MPP
registers.
So, drop the code relating to that.
Fixes: 87c220d0 ("arm: mvebu: mvebu_armada-8k: Add support for initializing iEi Puzzle-M801 networking")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Current CP1 pinctrl that is set on the Puzzle M801 is incorrect.
CP1 pins are only used for the SMI bus and the MSS I2C, all other
pins are just GPIO-s.
Due to this being set completely wrong, the pinctrl was actually
ended up being hardcoded in the board_early_init_f() step so that
SMI would work.
That is obviously not the right thing to do, so convert the register
hex values that were being written to individual pin modes and set it
in the DTS.
Add the SMI pins to the CP1 MDIO node as otherwise CP1 pinctrl does
not get probed without an consumer.
Fixes: 2ae2b8a2 ("arm: mvebu: Initial iEi Puzzle-M801 support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Select SPL_SKIP_LOWLEVEL_INIT on 32bit Armada platforms via Kconfig,
as this was removed from mach/config.h in a2ac2b96 ("Convert
CONFIG_SKIP_LOWLEVEL_INIT et al to Kconfig").
Signed-off-by: Stefan Roese <sr@denx.de>
Fixes: a2ac2b96 ("Convert CONFIG_SKIP_LOWLEVEL_INIT et al to Kconfig")
Cc: Tom Rini <trini@konsulko.com>
Cc: Marek Behún <kabel@kernel.org>
Cc: Pali Rohár <pali@kernel.org>
Tested-by: Pali Rohár <pali@kernel.org>
There were several changes for this structure but the documentation was
not changed at the time. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge (PCIe Root Port) for Aardvark is emulated in U-Boot,
add support for handling and propagation of CRSSVE bit.
When CRSSVE bit is unset (default), driver has to reissue config
read/write request on CRS response.
CRSSVE bit is supported only when CRSVIS bit is provided in read-only
Root Capabilities register. So manually inject this CRSVIS bit into read
response for that register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge is working for the PCIe Root Port, U-Boot's PCI_PNP
code automatically enables memory access and bus mastering when needed.
We do not need to enable it when setting the HW up.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Aardvark does not have a real PCIe Root Port device on the root bus.
Instead it has PCIe registers of PCIe Root Port device mapped in
internal Aardvark memory space starting at offset 0xc0.
The PCIe Root Port itself is normally available as a PCI Bridge device
on the root bus with bus number zero. Aardvark instead has the
configuration registers of this PCI Bridge at offset 0x00 of Aardvark's
memory space, but the class code of this device is Mass Storage
Controller (0x010400), instead of PCI Bridge (0x600400), which causes
U-Boot to fail to recognize it as a P2P Bridge
Add a hook into the pcie_advk_read_config() / pcie_advk_write_config()
functions to redirect access for root bus from PIO transfer to this
internal Aardvark memory space. This will allow U-Boot to access
configuration space of this PCI Bridge which represents PCIe Root Port.
Redirect access to PCI Bridge registers in range 0x10 - 0x34 to driver's
internal buffer (cfgcache[]). This is because at those addresses
Aardvark has different registers, incompatible with config space of a
PCI Bridge.
Redirect access to PCI Bridge register PCI_ROM_ADDRESS1 (0x38) to
Aardvark internal address for that register (0x30).
When reading PCI Bridge register PCI_HEADER_TYPE, set it explicitly to
value Type 1 (PCI_HEADER_TYPE_BRIDGE) as PCI Bridge must be of Type 1.
When writing to PCI_PRIMARY_BUS or PCI_SECONDARY_BUS registers on this
PCI Bridge, correctly update driver's first_busno and sec_busno
variables, so that pcie_advk_addr_valid() function can check if address
of any device behind the root bus is valid and that PIO transfers are
started with correct config type (1 vs 0), which is required for
accessing devices behind some PCI bridge after the root bus.
U-Boot's PCI_PNP code sets primary and secondary bus numbers as relative
to the configured bus number of the root bus. This is done so that
U-Boot can support multiple PCIe host bridges or multiple root port
buses, when internal bus numbers are different.
Now that root bus is available, update code in pcie_advk_read_config()
and pcie_advk_write_config() functions to correctly calculate real
Aardvark bus number of the target device from U-Boot's bus number as:
busno = PCI_BUS(bdf) - dev_seq(bus)
Stefan: Small fix of header masking as suggested by Pali.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Aardvark reports Disabled and Hot Reset LTSSM states as values >= 0x20.
Link is not up in these states, so fix pcie_advk_link_up() function.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
These are part of SOC_CONTROL_REG1 register, not PEX_CAPABILITIES_REG.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Remove unused PCIe functions from SerDes code. They are unused and are
duplicated either from generic PCIe code or from pci_mvebu.c.
Remove also unused PCIe macros from SerDes code. They are just obfuscated
variants of standards macros in include/pci.h or in pci_mvebu.c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
This code is trying to parse PCIe config space of PCIe card connected on
the other end of link and then is trying to force 5.0 GT/s speed via Target
Link Speed bits in PCIe Root Port Link Control 2 Register on the local part
of link if it sees that card supports 5.0 GT/s via Max Link Speed bits in
Link Capabilities Register.
The code is incorrect for more reasons:
- Accessing config space of an endpoint card cannot be done immediately.
If the PCIe link is not up, reading vendor/device ID registers will
return all ones.
- Parsing is incomplete, so it can cause issues even for working cards.
Moreover there is no need to force speed to 5.0 GT/s via Target Link Speed
bits on PCIe Root Port Link Control 2 Register. Hardware changes speed from
2.5 GT/s to 5.0 GT/s autonomously when it is supported.
Most importantly, this code does not change link speed at all, since
because after updating Target Link Speed bits on PCIe Root Port Link
Control 2 Register, it is required to retrain the link, and the code for
that is completely missing.
The code was probably needed for making buggy endpoint cards work. Such a
workaround, though, should be implemented via PCIe subsystem (via quirks,
for example), as buggy cards could also affect other PCIe controllers.
Note that this code is fully unrelated to a38x SerDes code and really
should not have been included in SerDes initialization. Usage of magic
constants without names and comments made this SerDes code hard to read and
understand.
Remove this PCIe application code from low level SerDes code. As this code
is configuring only 5.0 GT/s part, in the worst case, it could leave buggy
cards at the initial speed of 2.5 GT/s (if somehow before this change they
could have been "upgraded" to 5.0 GT/s speed even with missing link
retraining). Compliant cards which just need longer initialization should
work better after this change.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI device ID is part of the PCIe controller SoC / revision. For Root
Complex mode (which is the default and the only mode supported currently
by U-Boot and Linux kernel), it is PCI device ID of PCIe Root Port device.
If there is some issue with this device ID, it should be set / updated by
PCIe controller driver (pci_mvebu.c), as this register resides in address
space of the controller. It shouldn't be done in SerDes initialization
code.
In the worst case (a specific board for example) it could be done via
U-Boot's weak function board_pex_config().
But it should not be overwritten globally for all A38x devices.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Enabling Common Clock Configuration bit in PCIe Root Port Link Control
Register should not be done unconditionally. It is enabled by operating
system as part of ASPM. Also after enabling Common Clock Configuration it
is required to do more work, like retraining link. Some cards may be broken
due to this incomplete Common Clock Configuration and some cards are broken
and do not support ASPM at all.
Remove this incomplete code for Common Clock Configuration. It really
should not be done in SerDes code as it is not related to SerDes, but to
PCIe subsystem.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Device/Port Type bits of PCIe Root Port PCI Express Capabilities Register
are read-only SAR registers and are initialized according to current mode
configured by PCIe controller. Changing PCIe controller mode (from Root
Complex mode to Endpoint mode or the other way) is possible via PCI
Express Control Register (offset 0x41A00), bit 1 (ConfRoot Complex). This
has to be done in PCIe controller driver (in our case pci_mvebu.c). Note
that default mode is Root Complex.
Maximum Link Speed bits of PCIe Root Port Link Capabilities Register are
platform specific and overwriting them does not make sense. They are set by
PCIe controller according to current SerDes configuration. For A38x it is
5.0 GT/s if SerDes supports appropriate speed.
Maximum Link Width bits of PCIe Root Port Link Capabilities Register are
read-only SAR registers, but unfortunately if this is not set correctly
here, then access PCI config space of the endpoint card behind this Root
Port does not work.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add comments to understand what this magic code is doing.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
SoC Control 1 Register (offset 0x18204) is already defined by macro
SOC_CONTROL_REG1.
Use macro SOC_CONTROL_REG1 instead of macro SOC_CTRL_REG in ctrl_pex.c
code and remove the other definition.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Replace magic register offsets by macros to make code more readable.
Add comments about what this code is doing.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Subroutines in comphy_usb2_power_up() and comphy_sgmii_power_up() functions
may fail. In this case, do not continue execution of current function and
instead jump to the end. Return value in 'ret' variable is already set.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
phy_txd_inv or phy_rxd_inv needs to be set only in case when
appropriate polarity is inverted. Otherwise these bits should be
cleared.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9406
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Marvell Armada 3700 Functional Specifications, section 52.2 PCIe Link
Initialization says that TXDCLK_2X_SEL bit needs to be enabled for PCIe
Root Complex mode.
Same change was included in TF-A project:
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/9408
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit 079b35a261 ("arm: a37xx: pci: Increase PCIe MEM size from 16 MiB
to 127 MiB") increased size of PCIe MEM to 127 MiB, which is the maximal
possible size for allocated 128 MiB PCIe window. PCIe IO size in that
commit was unchanged.
Armada 3720 PCIe controller supports 32-bit IO space mapping so it is
possible to assign more than 64 KiB if address space for IO.
Currently controller has assigned 127 MiB + 64 KiB memory and therefore
there is 960 KiB of unused memory. So assign it to IO space by increasing
IO window from 64 KiB to 1 MiB.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 079b35a261 ("arm: a37xx: pci: Increase PCIe MEM size from 16 MiB to 127 MiB")
Reviewed-by: Stefan Roese <sr@denx.de>
Remove the latest reference of CONFIG_USER_LOWLEVEL_INIT in code
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove the following STV0991 specific configs:
- CONFIG_STV0991 (never used, only defined in CONFIG_SYS_EXTRA_OPTIONS)
- CONFIG_STV0991_HZ (replaced by generic CONFIG_SYS_HZ)
- CONFIG_STV0991_HZ_CLOCK (replaced by generic CONFIG_SYS_HZ_CLOCK)
This patch allows to reduce the file config_whitelist.txt.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move CONFIG_BOOTCOMMAND defined in Kconfig in the board defconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Using the tools moveconfig.py to move the following config in the
defconfig files:
CONFIG_USB_HOST_ETHER
CONFIG_USB_ETHER_ASIX
CONFIG_USB_ETHER_MCS7830
CONFIG_USB_ETHER_SMSC95XX
These option are already migrated since the commit f58ad98a62 ("usb: net:
migrate USB Ethernet adapters to Kconfig") and the commit ae3584498b
("usb: net: migrate CONFIG_USB_HOST_ETHER to Kconfig").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This converts the CONFIG_STM32_FLASH to Kconfig by using
tools/moveconfig.py
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This reverts commit d5d726d3cc,
which breaks boards which ship with multiple SD/eMMC sockets.
This stm32mp1.h config is not used only by the ST reference
boards, but all the other STM32MP1 based boards in U-Boot, so
changes to this stm32mp1.h cannot break the other boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add protection on presence and order of the phy node sub node
by using the mandatory reg information.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The vbus-supply is an optional property of sub-node connector node.
and no more in the usb phyc node (in first proposed binding).
This regulator for USB VBUS may be needed for host mode.
See the latest kernel binding for details in
Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml.
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
#phy-cells = <0>;
connector {
compatible = "usb-a-connector";
vbus-supply = <&vbus_sw>;
};
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The stm32 platforms never had to support an ATAGs-based Linux Kernel,
so remove the bi_boot_params initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
These platforms never had to support an ATAGs-based Linux Kernel, so
remove the options.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
- pcie_dw_meson: fix usb fail when pci link fails to go up
- Sync Amlogic DT from Linux 5.14
- dwc3-meson-gxl: add AXG compatible
- dts: keep back HW order for MMC devices since change in Upstream Linux
- Cleanup local AXG DT USB nodes now everything is upstream
- distro_bootcmd: run pci enum for scsi_boot just like it is done for nvme_boot
- New Boards:
- Odroid-HC4: a variant of Odroid-C4 with 2 SATA ports (via PCIe-SATA bridge)
- Beelink GS-King X: A variant of the other Beelink board with 2 SATA ports (via USB3-SATA bridge)
- Banana Pi M5: another credit card SBC
- JetHub D1/H1: home automation controllers
- Radxa Zero: another RPi Zero sized SBC
-----BEGIN PGP SIGNATURE-----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=pDip
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20211007' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add new SoC ID for S905Y2 found in Radxa Zero
- pcie_dw_meson: fix usb fail when pci link fails to go up
- Sync Amlogic DT from Linux 5.14
- dwc3-meson-gxl: add AXG compatible
- dts: keep back HW order for MMC devices since change in Upstream Linux
- Cleanup local AXG DT USB nodes now everything is upstream
- distro_bootcmd: run pci enum for scsi_boot just like it is done for nvme_boot
- New Boards:
- Odroid-HC4: a variant of Odroid-C4 with 2 SATA ports (via PCIe-SATA bridge)
- Beelink GS-King X: A variant of the other Beelink board with 2 SATA ports (via USB3-SATA bridge)
- Banana Pi M5: another credit card SBC
- JetHub D1/H1: home automation controllers
- Radxa Zero: another RPi Zero sized SBC
Add documentation bits for the Radxa Zero
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: updated u200 MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add a defconfig for the Radxa Zero SBC, using an Amlogic S905Y2 chip.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: updated u200 MAINTAINERS & add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import the initial dts queued for Linux 5.16.y
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Alpha sort the Amlogic dtb list (same as the kernel).
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for new home automation devices.
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console
Patches from:
- JetHub H1
https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.inhttps://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.inhttps://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: removed unused variable value]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
JetHub devices uses its own boot sequence with "rescue" button
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
