When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.
This commit also introduces the configurable options in Kconfig.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This driver adds NAND support to SPL.
It was tested on Allwinner A20.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add kconfig options for various SPI flashes and use them in cm-fx6 defconfig.
Cc: Jagan Teki <jteki@openedev.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Since commit 09c3280754 (mtd, nand: Move common functions from
cmd_nand.c to common place), NAND commands would not work at all
on large devices.
=> nand read 80000000 10000 10000
NAND read: Offset exceeds device limit
=> nand erase 100000 100000
NAND erase: Offset exceeds device limit
The type of the "size" of "struct mtd_info" is uint64_t, while
mtd_arg_off_size() and mtd_arg_off() treat chipsize as int type.
The chipsize is wrapped around if the argument is given with 2GB
or larger.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Added SPI_FLASH_DATAFLASH entry on Kconfig with help description.
data flash driver comes with good decription, hence moved the
same on to kconfig help decription.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Haikun Wang <haikun.wang@freescale.com>
Added SPI_FLASH_MTD entry on Kconfig with help description.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Rename CONFIG_SF_DATAFLASH into CONFIG_SPI_FLASH_DATAFLASH
as it follows the naming convention same as remaining configs.
Signed-off-by: Jagan Teki <jteki@openedev.com>
sst25wf040b doesn't support Auto Address Increment Programming command.
Remove SST_WR flag.
Signed-off-by: Haikun Wang <B53464@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Move common functions from cmd_nand.c (for calculating offset
and size from cmdline paramter) to common place, so they could
used from other commands which use mtd partitions.
For onenand the arg_off_size() is left in common/cmd_onenand.c.
It should use now the common arg_off() function, but as I could
not test onenand I let it there ...
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Add MTD layer driver for spi, original patch from:
http://git.denx.de/?p=u-boot/u-boot-mips.git;a=commitdiff;h=bb246819cdc90493dd7089eaa51b9e639765cced
Changes from Heiko Schocher against this patch:
- Remove compile error if not defining CONFIG_SPI_FLASH_MTD:
LD drivers/mtd/spi/built-in.o
drivers/mtd/spi/sf_probe.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
drivers/mtd/spi/sf_ops.o: In function `spi_flash_mtd_unregister':
/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: multiple definition of `spi_flash_mtd_unregister'
drivers/mtd/spi/sf_params.o:/home/hs/abb/imx6/u-boot/drivers/mtd/spi/sf_internal.h:168: first defined here
make[1]: *** [drivers/mtd/spi/built-in.o] Fehler 1
make: *** [drivers/mtd/spi] Fehler 2
- Add a README entry.
- Add correct writebufsize, to fit with Linux v3.14
MTD, UBI/UBIFS sync.
Note (From Jagan): For testing raw mtd parition erase/read/write operations
using cmd_sf, sf_mtd should be required to register the spi flash device to
MTD layer but the sf_mtd_info ops were not required until and unless if we
use any flash filesystem layer say for example UBI. Due to this the foot-print
got increased ~290bytes in non-UBI case here that should be acceptible.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Jagannadh Teki <jteki@openedev.com>
Reviewed-by: Jagannadh Teki <jteki@openedev.com>
Atmel DataFlash chips have commands different from common spi
flash commands.
Atmel DataFlash also have special page-size.
This driver add support for accessing Atmel DataFlash.
It is based on the Driver Model.
Example:
=> sf probe 1:0
SPI DataFlash: Detected AT45DB021B with page size 264 Bytes, erase size 264 Bytes, total 264 KiB, revision d
=> sf erase 0 42000
SF: 270336 bytes @ 0x0 Erased: OK
=> mw.l 82000000 45444342 20000
=> sf write 82000000 0 42000
SF: 270336 bytes @ 0x0 Written: OK
=> sf read 83000000 0 42000
SF: 270336 bytes @ 0x0 Read: OK
=> cmp.b 82000000 83000000 42000
Total of 270336 byte(s) were the same
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Tested-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Chakra Divi <cdivi@openedev.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This reverts commit f76eba38b3.
This patch did not have a full and proper copyright/S-o-b chain.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Conflicts:
include/configs/sun6i.h
include/configs/sun8i.h
commit c316f57 "mtd: OMAP: Enable GPMC prefetch mode" only enabled
prefetch mode for 8 bit nand access, this adds 16 bit as well.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
The prefech mode is a feature of the gpmc, not the ELM. An am3517
does not have an elm, but can do prefeches, so move the code out
of the CONFIG_NAND_OMAP_ELM ifdef.
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.
Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This changes enable ONFI detection. The Read ID command now allows
one address byte which is needed for ONFI detection. To read the
ONFI parameter page, the NAND_CMD_PARAM need to be supported. The
CMD code enables one command and one address byte along with reading
data from flash using R/B#, as specified by ONFI.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Add option to choose between current 24-error correction and 32-error
correction through Kconfig. 32-error correction allow to use NAND
chips which require up to 8-bit error correction per 512 byte (when
using 2K pages).
Signed-off-by: Stefan Agner <stefan@agner.ch>
This commit allows users to enable/disable the Freescale NFC
controller found in systems like Vybrid (VF610), MPC5125, MCF54418
or Kinetis K70 via Kconfig with more detailed help docs.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefano Babic <sbabic@denx.de>
[scottwood: updated vf610twr_nand_defconfig]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use in-band bad block table (NAND_BBT_NO_OOB) which allows to
use the full OOB for hardare ECC purposes. Since there is no
ECC correction on the OOB it is also safer to use in-band area
to store the bad block table marker.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Implement read of OOB area only. When using column and sector size
properties, only parts of the page can be read. However, this works
only when hardware ECC is disabled, otherwise the ECC engine would
ruin the data in the buffer. To allow OOB only reads, three points
had to be addressed:
- Set ECC mode per command.
- Handle NAND_CMD_READOOB seperate. Make sure column and sector
size is correctly set up, while disabling ECC.
- Now, the OOB data end up at the beginning of the buffer. Remove
the special handling of OOB (spareonly).
Especially bad block scans benefit from this change. On a 512MiB
SLC NAND device, the bad block scan took 1.5s less than before.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Since we do not support sub-page writes anyway, reading the page
back to the controller on SEQIN command is not required. Remove
the page read on SEQIN.
However, the column/page values relevant to the SEQIN command, hence
set the column/row address on SEQIN command.
Signed-off-by: Stefan Agner <stefan@agner.ch>
To improve performance we remember the current page in the buffer
and avoid reading it twice. This implicit page cache increases
complexity while does not increase performance in real world cases.
This patch removes that feature.
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Calculate ecc strength according oobsize, but not hardcoded
which is not aligned with kernel driver
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <b37916@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Freeing allocated memory to priv before returning
from the function
Signed-off-by: Raghav Dogra <raghav@freescale.com>
[scottwood: removed unnecessary cast]
Signed-off-by: Scott Wood <scottwood@freescale.com>
On systems with caches enabled, NAND I/O may need to flush/invalidate
the cache during read/write operations. For this to work correctly, all
buffers must be cache-aligned. Fix nand_verify*() to allocate aligned
buffers.
This prevents cache alignment warnings from being spewed when using
U-Boot to write an updated version of itself to flash on NVIDIA Tegra
Seaboard (after perturbation of stack/data layout in current
u-boot-dm/next branch).
I have validatd (executed) nand_verify(), but I don't think I've executed
nand_verify_page_oob(); testing of that would be useful.
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Fixes: 59b5a2ad83 ("nand: Add verification functions")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Scott Wood <scottwood@freescale.com>
This printf() should have a newline at the end. Add it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Default name of spi flash like this "0:0", update it to "spi_flash@0:0".
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Upto now flash sector_size is assigned from params which isn't
necessarily a sector size from vendor, so based on the SECT_*
flags from flash_params the erase_size will compute and it will
become the sector_size finally.
Bug report (from Bin Meng):
=> sf probe
SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB,
total 2 MiB, mapped at ffe00000
=> sf erase 0 +100
SF: 65536 bytes @ 0x0 Erased: OK
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With SPI flash moving to driver model, commit fbb0991 "dm: Convert
spi_flash_probe() and 'sf probe' to use driver model" ignored the
SST flash-specific write op (byte program & word program), which
actually broke the SST flash from wroking.
This commit makes SST flash work again under driver model, by adding
SST flash-specific handling in the spi_flash_std_write().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add a new member 'flags' in struct spi_flash to store the flash flags
during spi_flash_validate_params().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
IFC has two register pages.Till IFC version 1.4 each
register page is 4KB each.But IFC ver 2.0 register page
size is 64KB each.IFC regiters structure is break into
two viz FCM and RUNTIME.FCM(Flash control machine) registers
are defined in PAGE0 and controls IFC generic functionality.
RUNTIME registers are defined in PAGE1 and controls NAND and
GPCM funcinality.
FCM and RUNTIME structures defination is common for IFC
version 1.4 and 2.0.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
IFC 2.0 doubled the SRAM size, which means double the number of
ECCSTAT registers. Fix the resulting array overflow.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This reverts commit 562f8df18d.
Note: Even un-reverting this patch couldn't works as expected, based
on the latest testing from Heiko Schocher.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Need to check value of spi_setup_slave and spi_setup_slave_fdt.
If their return value 'bus' is NULL, there is no need to pass it
to following spi_flash_probe_tail.
If 'bus' is null, the original function flow is as following:
spi_flash_probe
|->spi_setup_slave
|->spi_probe_bus_tail
|->spi_flash_probe_slave
|->spi_free_slave
Alougth check the pointer in spi_free_slave is ok, checking the return value
of spi_setup_slave and spi_setup_slave_fdt is better.
Before this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
SF: Failed to set up slave
data abort
pc : [<fff66dcc>] lr : [<fff7628c>]
reloc pc : [<87814dcc>] lr : [<8782428c>]
sp : fdf4fcf0 ip : e630396c fp : fe0d0888
r10: fffa2538 r9 : fdf4feb8 r8 : 02625a00
r7 : 00000002 r6 : fff94ec0 r5 : 00000000 r4 : 9355553c
r3 : 1af0593c r2 : cb3fe030 r1 : fff94eb8 r0 : e59ff018
Flags: nZCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
"
After this fix:
"
=> sf probe 0:2
FSL_QSPI: Not a valid cs !
Failed to initialize SPI flash at 0:2
"
No data abort using this patch.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Poll both the Read status and Flag status registers
for sucessful erase and program operations for the
Micron devices with E_FSR flag set in params table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
CONFIG_SPI does not exist in Kconfig in the first place, so the
dependency "depends on DM && SPI" is never met, i.e., DM_SPI_FLASH
can never be enabled (unless you ignore the dependency in an illegal
way. See below.)
Actually, some defconfigs such as socfpga_*_defconfig define
CONFIG_DM_SPI_FLASH=y, but it never appears in the .config file
because of this wrong dependency.
On the other hand, all the Tegra boards enable DM_SPI_FLASH because
config DM_SPI_FLASH
default y
silently ignores the dependency.
Unfortunately, this style of CONFIG definition is abused everywhere
in U-Boot, so we easily miss such a wrong dependency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Permit use of a udevice to talk to SPI flash. Ultimately we would like
to retire the use of 'struct spi_flash' for this purpose, so create the
new API for those who want to move to it.
Signed-off-by: Simon Glass <sjg@chromium.org>
In the case where the arch defines a custom map_sysmem(), make sure that
including just mapmem.h is sufficient to have these functions as they
are when the arch does not override it.
Also split the non-arch specific functions out of common.h
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
The controller's Reed-Solomon ECC hardware is
used except of course for raw reads and writes.
It covers in- and out-of-band data together.
The SPL framework is supported.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
