The PCI Bridge which represents mvebu PCIe Root Port has Expansion ROM
Base Address register at offset 0x30 but its meaning is different that
of PCI's Expansion ROM BAR register, although the address format of
the register is the same.
In reality, this device does not have any configurable PCI BARs. So
ensure that write operation into BARs (including Expansion ROM BAR) is a
noop and registers always contain zero address which indicates that BARs
are unsupported.
Fixes: a7b61ab58d ("pci: pci_mvebu: Properly configure and use PCI Bridge (PCIe Root Port)")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Since u32 takes up 4 bytes, we need to divide the number of u32s by 4
for cfgcache.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable KSZ9x01 PHY driver in DHCOR common configuration, since the
AV96 board has this PHY populated on the PCB.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The ethernet PHY must be reset on AV96, however DWMAC currently does
not support the MDIO-bus PHY GPIO reset bindings and the ethernet MAC
PHY reset property is going away on next DT sync. Add PHY specific
reset bindings to trigger the PHY reset and fix sporadic ethernet
malfunctions, until the next DT sync.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The variables retaining the strap values have to be initialized, always,
make it so. Moreover, free the requested GPIO list at the end to avoid
wasting memory.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The Micrel PHYs on known DHSOM based boards take a while to come out
of reset, increase the auto-negotiation timeout to prevent it from
timing out in case the ethernet is used right after the board was
reset.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add script to read U-Boot from SD card and write it to matching
locations in the SPI NOR, thus making the SPI NOR bootable. The
script erases the entire SPI NOR, including U-Boot environment,
to make sure the installation is clean. To retain environment
from current running U-Boot, run 'saveenv' after running the
'update_sf' script.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The USB hub on STM32MP1 DHCOM boards needs to wait a bit longer until
the USB Vbus is stable. Increase the USB power-good delay to 1 s.
This adds default-undefined STM32MP_BOARD_EXTRA_ENV variable into
stm32mp15_common.h to reduce duplication in board-specific config
files adding custom environment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The alternate function of PD20 is 4 as per the datasheet of
sama7g5 and not 5 as defined earlier.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Hari Prasath <Hari.PrasathGE@microchip.com>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
The resync of the device trees from Linux 5.16-rc3 caused aliases
to appear on the MMC devices which changed the numbering.
This changed the default boot device and caused boot failure.
Update the mmcdev variable to reflect the new aliases.
Signed-off-by: Adam Ford <aford173@gmail.com>
The resync of the device trees from Linux 5.16-rc3 caused aliases
to appear on the MMC devices which changed the numbering.
This broke the reading/writing of the environmental variables,
so update the defconfig accordingly.
Signed-off-by: Adam Ford <aford173@gmail.com>
The rzg2_beacon_defconfig creates an image for RZ/G2[MNH] and
as such creates three different device trees and each of them
have a corresponding -u-boot.dtsi file which are basically
copies of each other. Create a common include file to be
referenced by each of the respective board-u-boot.dtsi files
to reduce duplicate code and simplify support going forward.
This also restores some lost functionality from the device
tree re-sync and updates the MAINTAINER file to include all
beacon-renesom device tree files.
Signed-off-by: Adam Ford <aford173@gmail.com>
The device trees for the Beacon RZ/G2[MNH] boards have undergone
some changes over time, so resync them now.
Signed-off-by: Adam Ford <aford173@gmail.com>
The RZ/G2 series uses an external clock as a reference to the AVB.
If this clock is controlled by an external programmable clock,
it must be requested by the consumer or it will not turn on.
In order to do this, update the driver to use bulk enable and
disable functions to enable clocks for boards with multiple clocks.
Signed-off-by: Adam Ford <aford173@gmail.com>
UEFI:
* correctly handle missing TPM device
* prepare for block devices for U-Boot as EFI app
-----BEGIN PGP SIGNATURE-----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=jVT6
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-01-rc4-2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request efi-2022-01-rc4-2
UEFI:
* correctly handle missing TPM device
* prepare for block devices for U-Boot as EFI app
# gpg: Signature made Fri 10 Dec 2021 04:29:20 AM EST
# gpg: using RSA key 6DC4F9C71F29A6FA06B76D33C481DBBC2C051AC4
# gpg: Good signature from "Heinrich Schuchardt <xypron.glpk@gmx.de>" [unknown]
# gpg: aka "[jpeg image of size 1389]" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6DC4 F9C7 1F29 A6FA 06B7 6D33 C481 DBBC 2C05 1AC4
Add a block driver which handles read/write for EFI block devices. This
driver actually already exists ('efi_block') but is not really suitable
for use as a real U-Boot driver:
- The operations do not provide a udevice
- The code is designed for running as part of EFI loader, so uses
EFI_PRINT() and EFI_CALL().
- The bind method probes the device, which is not permitted
- It uses 'EFI' as its parent device
The new driver is more 'normal', just requiring its platform data be set
up in advance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
UCLASS_EFI_LOADER is used for devices created by applications and
drivers loaded by U-Boots UEFI implementation.
This patch provides a new uclass (UCLASS_EFI_MEDIA) to be used for devices
that provided by a UEFI firmware calling U-Boot as an EFI application.
If the two uclasses can be unified, is left to future redesign.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
These names are better used for access to devices provided by an EFI
layer. Use EFI_LOADER instead here, since these are only available in
U-Boot's EFI_LOADER layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When the TCG2 protocol is installed in efi_tcg2_register(),
TPM2 device must be present.
tcg2_measure_pe_image() expects that TCP2 protocol is installed
and TPM device is available. If TCG2 Protocol is installed but
TPM device is not found, tcg2_measure_pe_image() returns
EFI_SECURITY_VIOLATION and efi_load_image() ends with failure.
The same error handling is applied to
efi_tcg2_measure_efi_app_invocation().
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
There are functions that calls tcg2_agile_log_append() outside
of the TCG protocol invocation (e.g tcg2_measure_pe_image).
These functions must to check that TCG2 protocol is installed.
If not, measurement shall be skipped.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This commit modify efi_tcg2_register() to return the
appropriate error.
With this fix, sandbox will not boot because efi_tcg2_register()
fails due to some missing feature in GetCapabilities.
So disable sandbox if EFI_TCG2_PROTOCOL is enabled.
UEFI secure boot variable measurement is not directly related
to TCG2 protocol installation, tcg2_measure_secure_boot_variable()
is moved to the separate function.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Literally adhering to the docs gave this wrong output:
U-Boot> setenv fdtaddr 0x87f00000
U-Boot> fdtaddr $fdtaddr
Unknown command 'fdtaddr' - try 'help'
Fixes: d80162cfc5 ("doc: Document how to apply fdt overlays")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This fixes two regressions: eMMC operation on boards with WiFi (so using
three MMC devices), and a repeated wrong error message in USB gadget
mode (fastboot, ums).
The sunxi MUSB glue driver has some code to check for external VBUS
presence when it's going to use the MUSB host mode, and it warns if
there is VBUS provided through the cable (in sunxi_musb_enable()).
This code was apparently copied to the USB gadget detection code
(g_dnl_board_usb_cable_connected()), but here we actually *expect*
external VBUS power, so a warning is wrong and confusing.
So far this message rarely triggered, but a recent patch (6fa41cdd19)
changed this:
===========================
=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe90000
A charger is plugged into the OTG
/A charger is plugged into the OTG
\A charger is plugged into the OTG
|A charger is plugged into the OTG
-A charger is plugged into the OTG
....
===========================
Remove the message for the gadget cable detection call, and just return
the status of the VBUS detection, as this is what the callers are after.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Commit 03510bf621 ("sunxi: only include alias for eMMC when mmc2
used") protected the eMMC alias in U-Boot's DT stub the with the
associated Kconfig symbol, but was actually using the wrong name.
Fix the name of the symbol to match what's defined in Kconfig and what
the defconfig files actually use.
Fixes: 03510bf621 ("sunxi: only include alias for eMMC when mmc2 used")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: 5kft@5kft.org
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
QSPI0 has a MX66LM1G45G SPI NOR flash connected.
Enable the controller and describe the flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
sama7g5 embedds an OSPI and a QSPI controller:
1/ OSPI0 Supporting Up to 200 MHz DDR. Octal, TwinQuad, Hyperflash
and OctaFlash Protocols Supported.
2/ QSPI1 Supporting Up to 90 MHz DDR/133 MHz SDR.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
sama7g5 QSPI has:
1/ One Octal Serial Peripheral Interfaces (QSPI0) Supporting Up to
200 MHz DDR. Octal, TwinQuad, Hyperflash and OctaFlash Protocols Supported
2/ One Quad Serial Peripheral Interfaces (QSPI1) Supporting Up to
90 MHz DDR/133 MHz SDR
The QSPI controller of SAMA7G5 uses different clock domains, hence extra
synchronization operations must be performed before accessing some
registers. Differentiate between the versions of the IP using has_gclk.
Differentiate between QSPI0 and QSPI1 with has_octal.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
bloblist - allow it to be allocated
sandbox config-header cleanup
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmGtgBARHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZiRggAlOeC1qnl5uEHRwzP/0OHAisek2W2ikZI
aJeNh1CHCfu5a//W6QInoR4knfYJM1nK5RFapKO83L4E3wzHgoL3u0OgikO2gRdt
YTl9rFIp6niSntoeP2MmtT1gBPq0kOGj6tD9KIameNLIOCrWgN0/VwVdiH9eXipc
N/egjGyOkIGoxYnQQaYnujiHMEEf14koFfO+RM9UYIsnm+9jJFiQ5nssm/waTvom
a18dGjHU1P6UIjMbLyq7QkmoDwpHMiHvK6q0C9BvKRLfW6EvhHFQLjsTOm4KXEmI
NoKDTkY9RD9c68wJWT4STEMpg0lGYj9S42Db9qI1g7WacLZlCbb6DA==
=hWWY
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5dec21a' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
binman refactoring to improve section handling
bloblist - allow it to be allocated
sandbox config-header cleanup
# gpg: Signature made Sun 05 Dec 2021 10:14:24 PM EST
# gpg: using RSA key B25C0022AF86A7CC1655B6277F173A3E9008ADE6
# gpg: issuer "sjg@chromium.org"
# gpg: Good signature from "Simon Glass <sjg@chromium.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B25C 0022 AF86 A7CC 1655 B627 7F17 3A3E 9008 ADE6
This is not needed anymore. Drop it to simplify the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CONFIG_SYS_ATA_PORT_ADDR is not used in the code anymore. Drop it and use
ATA_PORT_ADDR() locally instead.
Drop CONFIG_IDE_RESET_ROUTINE and CONFIG_IDE_SWAP_IO which are also
unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used by sandbox since it uses driver model for the timer.
Drop it.
Also update the tools_only build to avoid build errors, since it does
actually build U-Boot too. Enable DM so we can use CONFIG_TIMER,
disable EFI_LOADER to avoid an error about board_quiesce_devices() and
disable NET to avoid having to define CONFIG_AVB_BUF_ADDR
Signed-off-by: Simon Glass <sjg@chromium.org>
This can go in the related header file. Drop the CONFIG option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present there are Kconfig options for tracing, but sandbox uses
plain #defines to set them. Correct this and make the tracing command
default to enabled so that this is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to have a list of related external blobs in a
single entry. An example is the DDR binaries used by meson. There are
9 files in total. Add support for this, so we don't have to have a
separate entry for each.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases entries encapsulate other data and it is useful to access
the data within. An example is the fdtmap which consists of a 16-byte
header, followed by a devicetree.
Provide an option to specify an alternative format when extracting files.
In the case of fdtmap, this is 'fdt', which produces an FDT file which can
be viewed with fdtdump.
Signed-off-by: Simon Glass <sjg@chromium.org>
If an older version of binman is used to list images created by a newer
one, it is possible that it will contain entry types that are not
supported. At present this produces an error.
Adjust binman to use a plain 'blob' entry type to cope with this, so the
image can at least be listed.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is necessary to symlink files containing external blobs into
the U-Boot tree in order for binman to find them. This is not very
convenient.
Add two new environment/Makefile variables to help with this. Add
documentation as well, fixing a related nit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Typically the bloblist is positioned at a fixed address in memory until
relocation. This is convenient when it is set up in SPL or before
relocation.
But for EFI we want to set it up only when U-Boot proper is running. Add
a way to allocate it using malloc() and update the documentation to cover
this aspect of bloblist.
Note there are no tests of this feature at present, nor any direct testing
of bloblist_init().
This can be added, e.g. by making this option controllable at runtime.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the constructor to work in the recommended way, where the node
properties are read in a separate function. This makes it more similar to
entry_Section.
Signed-off-by: Simon Glass <sjg@chromium.org>
