STiH410 has 2 PHYs wired on the DWC3 IP, USB2 and USB3 PHYs.
As currently no U-boot driver is available for the USB3 PHY and to avoid
issue during DWC3 drive probe, we use DWC3 IP with only USB2 PHY
using stih410-b2260-u-boot.dtsi file.
Fixes: 2fd4242cc5 ("ubs: xhci-dwc3: Enable USB3 PHY when available")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Eliminate code duplication: the same PARTS_DEFAULT was defined in
am57xx_evm.h and in dra7xx_evm.h. Extract it to environment/boot.h and
use in all OMAP5-based boards.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Generate SoCFPGA boot header version 1 instead of version 0 for Arria10.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
Add support for the SoCFPGA header v1 , which is used on Arria 10.
Thus far the mkimage-socfpga image only supported header format v0
used on Cyclone V and Arria V, but is not supported on Arria 10.
The layout of the v0 and v1 header is similar, yet there are a few
differences, see the patch body for details.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
The structure is passed around correctly, create local instances
where necessary and zap the global struct socfpga_image instance.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
Add support for the SoCFPGA header v1, which is used on Arria 10.
The layout of the v0 and v1 header is similar, yet there are a few
differences which make it incompatible with previous v0 header, so
add a new entry.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
The Arria10 uses slightly different boot image header than the Gen5 SoCs,
in particular the header itself contains an offset from the start of the
header to which the Arria10 jumps. This offset must not be negative, yet
the header is placed at offset 0x40 of the bootable binary. Therefore, to
jump into U-Boot, add a trampoline just past the Arria10 boot header and
point to this trampoline at fixed offset from the header generated using
the mkimage -T socfpgaimage_v1 . Note that it is not needed to jump back
to offset 0x0 of the image, it is possible to jump directly at the reset
label and save processing two instructions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
This patch adds the driver for the Amlogic Meson Successive Approximation
Register (SAR) A/D Converter based on the Linux IIO driver thanks to the
great work of Martin Blumenstingl.
The driver has been adapted to U-Boot and the ADC UClass.
This patch depends on the regmap "regmap: add regmap_update_bits() helper"
patch and has been tested using the newly introducted "adc" CLI command
in the "cmd: add ADC cli commands" patch.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add calls to regmap_read/modify_bits/write even if the proper memory
read/write calls are not executed in sandbox.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the regmap_update_bits() to simply the read/modify/write of registers
in a single command. The function is taken from Linux regmap
implementation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable vrefbuf on stm32mp15, to be used by ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add VREF clock gating, that may be used by STM32 VREFBUF regulator.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable DM_REGULATOR_STPMU1 flag to activate regulator
driver for STM32MP15 SoC and CMD_REGULATOR flag to be
able to set/get regulator state int U-boot command line.
Disable PMIC_CHILDREN as this flag is not needed in SPL
for STM32MP1.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add regulator bindings to get access to regulator managed
by drivers/power/regulator/stpmu1.c regulator driver.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable support for the regulator functions of the STPMU1X PMIC. The
driver implements get/set api for the various BUCKS and LDOs supported
by the PMIC device. This driver is controlled by a device tree node
which includes voltage limits.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This driver binds and manages the following regulator of
SoC's PWR block :
- reg11
- reg18
- usb33
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since kirkwook SPI was recently converted to DM, add compatible strings
to the SPI flash devices to make them work with the new driver.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Boot android over emmc by default thru FIT image
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Suggested-by: Andrew F.Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Enable the FDT library overlay support for all TI SOC family.
Without this option, when Loading fdt from FIT image, the
following warning is seen.
"config with overlays but CONFIG_OF_LIBFDT_OVERLAY not set".
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Suggested-by: Andrew F.Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
'commit dda0bd674481 ("arm: dra762: Add support for device package identification")'
introduces ABZ and ACD package identification.
This patch is to extend usage of "fastboot getvar cpu" for
DRA76x ABZ and ACD devices.
Helps in fixing the boot warning.
Warning: fastboot.cpu: unknown CPU rev: 123863298
on
CPU : DRA762-GP ES1.0 ABZ package
Model: TI AM5748 IDK
Board: AM574x IDK REV 1.0A
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove SYS_USE_NANDFLASH, SYS_USE_MMC as they are deprecated and
unused.
The board configurations already use CONFIG_SD_BOOT and
CONFIG_NAND_BOOT respectively.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[eugen.hristev@microchip.com: rework on latest u-boot]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
According to the REVB schematic, fix the USB vbus power enable pin.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
To fix the issue of write the rootfs.ubi, adjust the smc timings
configuration of the nand controller.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
When a pin is muxed to a peripheral or as a GPIO, the only
configuration that can be set is the pullup. It is too restrictive
so this patch allows to give a full configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The drive strength has to be set to medium for the NAND data lines.
With a low drive, we can get some data corruption.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Add PCIe driver for Intel FPGA PCIe IP. This driver operates the PCIe IP in
rootport mode only, the EP mode is not supported. The driver is tested
with the Intel e1000e NIC driver.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
This patch adds smc and hvc commands, that allow issuing Secure Monitor
Calls and Hypervisor Calls conforming to the ARM SMC Calling Convention.
Add Kconfig items to allow each command can be individually enabled.
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pinctrl bindings has changed for Amlogic Meson SoCs since Linux 4.13,
update the pinctrl driver to take this in account.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Taking into account the Amlogic Family name starts with GX, including
the GXBB, GXL and GXM SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On all STM32F4 and F7 SoCs family (except STM32F429), PLLSAI
output P can be used as 48MHz clock source for USB and SDMMC.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Tested By: Bruno Herrera <bruherrera@gmail.com>
Add two more gpio-leds to sandbox test device tree with default-state
property set to "on"/"off".
Add dm_test_led_default_state() to check that these new LED's are set to
LEDST_ON and LEDST_OFF.
dm: led: add testcase for "default-state" property
Add two more gpio-leds to sandbox test device tree with default-state
property set to "on"/"off".
Add dm_test_led_default_state() to check that these new LED's are set to
LEDST_ON and LEDST_OFF.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
To avoid board specificy LED activation code, automatically
activate gpio-leds with "default-state" property during bind().
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Add support for the device tree property "default-state". This feature
might be useful for LEDs indicating "power on" or similar states.
Note: Even with this commit gpio-leds remain in reset state. That's
because the led_gpio is not probed until DM_FLAG_ACTIVATED is set.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Provide an alternate path for sparse-images to be
written to MMC. For example, via tftp on platforms
that don't support fastboot protocol. Or when an
image is to written at some offset, rather than the
start of a partition.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
[trini: Guard with CONFIG_FASTBOOT_FLASH tests, use LBAF for lbaint_t
printing]
Signed-off-by: Tom Rini <trini@konsulko.com>
On a socfpga_cyclone5 based board the SD card, was never powered up. For
other dw_mmc based SoCs dwmci_probe() is called in the platform specific
probe(). It seems this call is missing for socfpga_dw_mmc.
With this change DWMCI_PWREN is set by dmwci_init().
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add the debug message for checking the mmc clock status.
It's helpful to debug the controlling clock.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
mmc_set_clock() function has the disable argument as bool type.
When mmc_set_clock is called, it might be passed to "true" or "false".
But it's too confusion whether clock is enabled or disabled with only
"true" and "false".
To prevent the confusion, replace to MMC_CLK_ENABLE/DISABLE macro from
true/false.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
