The '_' character is discouraged in the node name, this patch adds the
new prefix of regulator subnode, with the '-' character, in STM32MP1 driver
to support the new naming rule in Linux kernel device trees.
It is a preliminary patch before Linux device tree synchronization
for STMicroelectronics boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
PCA9451A uses similar BUCKs and LDO regulators as PCA9450B/C but
has LDO2 and LDO3 removed. So reuse pca9450 PMIC and regulator driver
and add new type for PCA9451A.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
The implementation is taken almost verbatim from Linux commit
2364a64d0673f ("regulator: pca9450: Make warm reset on WDOG_B assertion")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now that a regulator driver exists for this PMIC, hook it up to the
device tree "regulators" subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Subordinate regulator drivers can use this enumerated ID instead of
matching the compatible string again.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Ignore the disabled children node in pmic_bind_children() so the
disabled regulators in device tree are not registered.
This patch is based on the dm_scan_fdt_node() code - only the
activated nodes are bound - and it solves possible issue when a
deactivated regulator is bound, error for duplicated regulator name
for example.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_POWER_FSL
CONFIG_POWER_FSL_MC13892
CONFIG_POWER_HI6553
CONFIG_POWER_LTC3676
CONFIG_POWER_PFUZE100
CONFIG_POWER_PFUZE3000
CONFIG_POWER_SPI
CONFIG_POWER_TPS65090_EC
CONFIG_POWER_TPS65218
CONFIG_POWER_TPS65910
Signed-off-by: Tom Rini <trini@konsulko.com>
As we have more legacy PMIC drivers to move to Kconfig, guard them all
with POWER_LEGACY or SPL_POWER_LEGACY. Do the same kind of check for
building the drivers too. This also means that we need to resort the
list slightly in the Makefile.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The support added later in this series tweaks the PMIC voltages in the
SPL. Enable support for the rn5t567 in SPL builds to allow this to be done
cleanly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for the rn5t568 PMIC to the rn5t567 driver.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Jaehoon Chung <j80.chung@samsung.com>
If the bd718x7 is required, but PMIC_CHILDREN is disabled, this
driver throws a compile error. Fix this by putting the function
to bind children into an if-statement checking for PMIC_CHILDREN.
Allowing PMIC_CHILDREN to be disabled in SPL saves some space and
still permits some read/write functions to access the PMIC in
early startup.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Avoid concatenation with following message.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use the log functions instead of pr_...() so we can avoid using __func__.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
For Rockchip boards with the all rk8xx series PMICs (excluding the
rk808), it is sometimes desirable to not boot whenever the device is
plugged in. An example would be for the Odroid Go Advance.
This provides a configurable option to check the PMIC says it was
powered because of a plug-in event. If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
This patch parallels the work done in the following patch series:
https://lore.kernel.org/u-boot/20220121133732.2397273-1-andre.przywara@arm.com/
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for sysreset shutdown for this PMIC. The values were pulled
from the various datasheets, but for now it has only been tested on
the rk817 (for an Odroid Go Advance).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
LDO5 has two separate control registers. LDO5CTRL_L is used if the
input signal SD_VSEL is low and LDO5CTRL_H if it is high.
The current driver implementation only uses LDO5CTRL_H. To make this
work on boards that have SD_VSEL connected to a GPIO, we add support
for specifying an optional GPIO and setting it to high at probe time.
In the future we might also want to add support for boards that have
SD_VSEL set to a fixed low level. In this case we need to change the
driver to be able to use the LDO5CTRL_L register.
This is a port of the same change in the Linux kernel:
8c67a11bae88 ("regulator: pca9450: Add SD_VSEL GPIO for LDO5")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Fabio Estevam <festevam@denx.de>
The pca9450 driver uses dm_i2c_{read,write}, which
are (unsurprisingly) only available with DM_I2C. Make sure one can't
create an unbuildable .config by adding proper dependencies.
While here, append "in SPL" to the prompt for the SPL_ variant so it
doesn't read the same as the one for the non-SPL_ variant.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add PCA9450 regulator driver. This is complementary driver for the BUCKn
and LDOn regulators provided by the PCA9450 PMIC driver. Currently the
driver permits reading the settngs and configuring the BUCKn and LDOn
regulators.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The upstream DT regulators node subnodes are named BUCKn and LDOn,
the downstream DT regulators node subnodes are named buckn and ldon,
add the upstream match.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The TPS65219 I2S PMIC features 3 Buck converters and 4 linear regulators,
2 GPOs, 1 GPIO, and 3 multi-function-pin.
This adds the PMIC driver, loading the regulator sub-nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add DT compatible string for PCA9450C PMIC. This is a variant of the
PCA9450 PMIC with 6 A dual-phase buck regulator and 3 A buck regulator,
and is software-wise compatible with the PCA9450B. This variant of the
PCA9450 is designed for use as companion PMIC for i.MX8MP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The tps65217 PMIC driver is used with am335x SoC based designs.
It is used in the SPL (MLO) as well, so the DM conversion only is
for u-boot proper.
This driver only allows simple reading/writing/dumping of the content
of its registers and requires the DM_I2C for proper operation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Up till now the CONFIG_POWER_TPS65217 has been defined in several header
files for am335x SoC.
This patch renames it to CONFIG_PMIC_TPS65217, which better reflects the
role of this IC circuit.
Moreover, new CONFIG_PMIC_TPS65217 has been introduced in Kconfig
to be used with boards, which both support DM_PMIC and DM_I2C.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Migrate all other platforms as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since TPS659412 and TPS659413 are both software compatible,
add a compatible string for the same inside tps65941.c.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
The AXP PMICs have the ability to power off the system. The existing
code for this is duplicated for each PMIC variant, and uses the legacy
non-DM "pmic_bus" interface. When SYSRESET is enabled, this can all be
replaced with a sysreset device using the DM_PMIC interface.
Since the trigger bit is the same on all PMIC variants, use the register
definitions from the oldest supported PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
These PMICs provide some combination of battery charger, fuel gauge,
GPIOs, regulators, and VBUS routing. These functions are represented
as child nodes in the device tree. Add the minimal driver needed to
probe these child devices and provide the DM_PMIC ops.
Enable the driver by default for SoCs that normally pair with a PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that there is a separate symbol to enable DM_PMIC in SPL, update the
the SPL-specific driver symbols to depend on this new option.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Kconfig symbols for two PMIC drivers (PMIC_AS3722 and DM_PMIC_MC34708)
were missing a dependency on DM_PMIC. To fix this inconsistency, and to
keep it from happening again, wrap the driver section with "if DM_PMIC"
instead of using a "depends on DM_PMIC" clause for each driver.
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add a proper Kconfig option for SPL so we can remove the hack in some of
the board config files.
This involves adding CONFIG_SPL_DM_PMIC to some of the configs as well
as updateing the Makefile rule for PMIC_RK8XX to exclude SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Add SPL_PMIC_RK8XX, enable when needed, handle undef of
CONFIG_DM_PMIC_PFUZE100 as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
TI J7200 EVM has lp876441 pmic that is similar to tps65941. Add support
for same with existing driver with new compatible.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210714205300.17424-2-g-tammana@ti.com
All devices based on ST-Ericsson Ux500 use a PMIC similar to AB8500
(Analog Baseband). There is AB8500, AB8505, AB9540 and AB8540
although in practice only AB8500 and AB8505 are relevant since the
platforms with AB9540 and AB8540 were cancelled and never used in
production.
In general, the AB8500 PMIC uses I2C as control interface, where the
different register banks are represented as separate I2C devices.
However, in practice AB8500 is always connected to a special I2C bus
on the DB8500 SoC that is controlled by the power/reset/clock
management unit (PRCMU) firmware.
Add a simple driver that allows reading/writing registers of the
AB8500 PMIC. The driver directly accesses registers from the PRCMU
parent device (represented by syscon in U-Boot). Abstracting it
further (e.g. with the i2c uclass) would not provide any advantage
because the PRCMU I2C bus is always just connected to AB8500 and
vice-versa.
The ab8500.h header is mostly taken as-is from Linux (with some
minor adjustments) to allow using similar code in both Linux and
U-Boot.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit does the same thing as Linux commit 33def8498fdd.
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Remove pmic_max8997/8 files about no-DM.
There are already existed max8997/8 as driver-model.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds basic register access and child regulator binding
for the Monolithic MP5416 Power Management IC which integrates
four DC/DC switching converters and five LDO regulators.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
