Add pl310 interrupt to the Zynq devicetree.
Signed-off-by: Alex Wilson <alex.david.wilson@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove unneeded address-cells form intc node because it is already setup
in parent node.
Add missing address-cells and size-cells to eth node to be shared for
every platform DTSes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do. Also allow the compatible
cadence gem binding that won't disable half duplex but works otherwise.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The size of the GEM's register area is only 0x1000 bytes.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Zynq is using Cadence IP where binding is documented in the Linux kernel
and there is no reason to use different binding.
Synchronize it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Due to dependencies between timer and CPU frequency, only changes by
powers of two are allowed. The clocksource driver prevents other
changes, but with cpufreq and its governors it can result in being
spammed with error messages constantly. Hence, remove the 222 MHz OPP.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Zynq UART is Cadence IP and the driver has been renamed accordingly.
Migrate the DT to use the new binding for the UART driver.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
To silence the warning
cpufreq_cpu0: failed to get cpu0 regulator: -19
from the cpufreq driver regarding a missing regulator,
add a fixed regulator to the DT.
Zynq does not support voltage scaling and the CPU rail should always be
supplied with 1 V, hence it is added in the SOC-level dtsi.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now zynq spi driver platform data is controlled by devicetree,
enable the status by saying "okay" on respective board dts to use
the devicetree generated platdata.
Ex:
&spi1 {
status = "okay";
};
Signed-off-by: Jagan Teki <jteki@openedev.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Our current motivation is to use OF initialization for RAM and UART.
But adding full DTS would be helpful in future, for instance,
for OF configuration of Ethernet, MMC, USB, etc.
This commit imports arch/arm/boot/dts/zynq-7000.dtsi from Linux 3.15-rc5
and adjusts the license comment block for SPDX.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch provides a basic fdt support for zynq u-boot.
zynq-7000.dtsi-> initial arch dts file
zynq-zed.dts -> initial zed board dts file
more devices should be added in subsequent patches.
u-boot build: once configuring of a board done
for building dtb with zynq-zed.dts as an input
zynq-uboot> make DEVICE_TREE=zynq-zed
Enabled CONFIG_OF_SEPARATE for building dtb separately.
There is a new binary called u-boot-dtb.bin which is a u-boot
with devicetree supported.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
