The OMAP5 silicon has new DDR PHY design, which includes a external PHY
as well. So configuring the ext PHY parameters here. Also the EMIF timimg
registers and a couple of DDR mode registers needs to be updated based on
the testing from the actual silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
The control module provides options to set various signal
integrity parameters like the output impedance, slew rate,
load capacitance for different pad groups. Configure these
as required for the omap5430 sevm board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Aligning all the clock related settings like the dpll frequencies, their
respective clock outputs, etc to the ideal values recommended for
OMAP5430 ES1.0 silicon.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
This is rework on config files of IGEP-based boards with the aim to remove
duplicated code to be more maintainable. Basically this patch creates a
common configuration file for both boards and only sets the specific option
in the board config file.
On board files the hardcored mach type was replaced in favour of using the
CONFIG_MACH_TYPE option.
More than 200 duplicated lines have been deleted.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
OMAP4 requires that parent domains scale ahead of dependent domains.
This is due to the restrictions in timing closure. To ensure
a consistent behavior across all OMAP4 SoC, ensure that
vdd_core scale first, then vdd_mpu and finally vdd_iva.
As part of doing this refactor the logic to allow for future
addition of OMAP4470 without much ado. OMAP4470 uses different
SMPS addresses and cannot be introduced in the current code
without major rewrite.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
TPS SET0/SET1 register is selected by a GPIO pin on OMAP4460 platforms.
Currently we control this pin with a mux configuration as part of
boot sequence.
Current configuration results in the following voltage waveform:
|---------------| (SET1 default 1.4V)
| --------(programmed voltage)
| <- (This switch happens on mux7,pullup)
vdd_mpu(TPS) -----/ (OPP boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -----------------------/ (OPP boot voltage)
Problem 1) |<----- Tx ------>|
timing violation for a duration Tx close to few milliseconds.
Problem 2) voltage of MPU goes beyond spec for even the highest of MPU OPP.
By using GPIO as recommended as standard procedure by TI, the sequence
changes to:
-------- (programmed voltage)
vdd_mpu(TPS) ------------/ (Opp boot voltage)
--------- (programmed voltage)
vdd_core(TWL6030) -------------/ (OPP boot voltage)
NOTE: This does not attempt to address OMAP5 - Aneesh please confirm
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
OMAP Voltage controller is used to generically talk to
PMICs on OMAP3,4,5 over I2C_SR. Instead of replicating code
in multiple SoC code, introduce a common voltage controller
logic which can be re-used from elsewhere.
With this change, we replace setup_sri2c with omap_vc_init which
has the same functionality, and replace the voltage scale
replication in do_scale_vcore and do_scale_tps62361 with
omap_vc_bypass_send_value. omap_vc_bypass_send_value can also
now be used with any configuration of PMIC.
NOTE: Voltage controller controlling I2C_SR is a write-only data
path, so no register read operation can be implemented.
Reported-by: Isabelle Gros <i-gros@ti.com>
Reported-by: Jerome Angeloni <j-angeloni@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Add parameters to the OMAP MMC initialization function so the board can
mask host capabilities and set the maximum clock frequency. While the
OMAP supports a certain set of MMC host capabilities, individual boards
may be more restricted and the OMAP may need to be configured to match
the board. The PRG_SDMMC1_SPEEDCTRL bit in the OMAP3 is an example.
Signed-off-by: Jonathan Solnit <jsolnit@gmail.com>
This change adds a basic support for Embest/Timll DevKit3250 board,
NOR and UART are the only supported peripherals for a moment. The board
doesn't require low-level init, because the initial SDRAM and GPIO
configuration is performed during kickstart bootloader execution.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This change adds an implementation of high-speed UART found on NXP
LPC32X0 SoCs. Such UARTs are enumerated as UART1, UART2 and UART7.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This change adds initial support for NXP LPC32x0 SoC series.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
To support sdhci controller, remove the CONFIG_S5P_MMC..
Instead, use the CONFIG_S5P_SDHCI/CONFIG_SDHCI.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
In driver mmc, generic s5p_sdhci code is implemented.
s5p_mmc file is dupulicated.
we are good that use the generic sdhci.
This patch supported the sdhci for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
To support the Samsung-SoC, added the basically functions.
Samsung-SoC didn't used the SDHCI_CTRL_HISPD.
And added set_control_reg callback for s3c64xx.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
When response type is R1b, mask value is added the SDHCI_INT_DAT_END.
but in while(), didn't check that flag.
So sdhci controller didn't work fine.
CMD6 didn't always complete.
So add the quirks for broken r1b response
and add the timeout value to prevent the infinite loop.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lei Wen<leiwen@marvell.com>
Some MMC cards, like my ancient 32.0MB SanDisk RS-MMC cards had issue if b_max
was set to 0x40 and DMA was enabled. Lower this value to 0x20, which allows
these cards to work too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This patch imports parts of two patches from the Freescale U-Boot with the following
commit messages:
ENGR00156405 ESDHC: Add workaround for auto-clock gate errata ENGcm03648
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/drivers/mmc/imx_esdhc.c?h=imx_v2009.08_12.01.01&id=e436525a70fe47623d346bc7d9f08f12ff8ad787
The errata, not applicable to USDHC, causes ESDHC to shut off clock to the card
when auto-clock gating is enabled for commands with busy signalling and no data
phase. The card might require the clock to exit the busy state, so the workaround
is to disable the auto-clock gate bits in SYSCTL register for such commands. The
workaround also entails polling on DAT0 bit in the PRSSTAT register to learn when
busy state is complete. Auto-clock gating is re-enabled at the end of busy state.
ENGR00156670-1 ESDHC/USDHC: Remove delay before each cmd and some bug fixes
http://git.freescale.com/git/cgit.cgi/imx/uboot-imx.git/commit/drivers/mmc/imx_esdhc.c?h=imx_v2009.08_12.01.01&id=a77c6fec8596891be96b2cdbc742c9824844b92a
Removed delay of 10 ms before each command. There should not be a need to have this
delay after the ENGR00156405 patch that polls until card is not busy anymore before
proceeding to next cmd.
This patch imports the polling part of both patches. The auto-clock gating code
don't apply for i.MX6 as implemented in these two patches.
SYSCTL_RSTA was defined twice. Remove one definition.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
The outdated struct mmc_csd was only used by old atmel_mci driver which was
removed in c9abb4260c.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
cc: Andy Fleming <afleming@freescale.com>
According to OMAP3 TRM, when the controller reports certain errors,
driver must perform a software reset. This is done by setting a bit
in SYSCTL and waiting it to clear:
- SRC on command timeout (CTO)
- SRD on data errors (DTO, DCRC and DEB)
This fixes a problem seen on OMAP3 pandora board with some cards
that won't work with a message printed multiple times:
timedout waiting on cmd inhibit to clear
Code loosely based on Linux omap_hsmmc driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
The message didn't state that it's waiting for STAT to _clear_,
and printing the STAT value itself can help to identify problems.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tom Rini <trini@ti.com>
According to OMAP3 TRM, PBIASLITEPWRDNZ bits must be cleared while MMC
power supply is being enabled and is ramping up (those bits might be
left set by the previous bootloader). It doesn't say what happens if
this procedure is violated, but better not to risk here and do things
as required.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tom Rini <trini@ti.com>
This patch sets the MMC width according to the MMC host capabilities.
It turned out, that there are some targets (e.g. GONI), which are able
to read data from SPI only at 4 bit mode.
This patch restricts the width number according to the MMC host.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andy Fleming <afleming@gmail.com>
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
lin_gadget: use common linux/compat.h
linux/compat.h: rename from linux/mtd/compat.h
lin_gadget: use common mdelay
gunzip: rename z{alloc, free} to gz{alloc, free}
fs/fat: align disk buffers on cache line to enable DMA and cache
part_dos: align disk buffers on cache line to enable DMA and cache
Merge our duplicate definitions with the common header.
Also fix drivers/usb/gadget/s3c_udc_otg_xfer_dma.c to
use min() instead of min_t() since we remove the latter
from compat.h.
Additionally use memalign() directly as the lin_gadget
specific kmalloc() macro is removed from lin_gadget_compat.h
by this patch.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This allows us to add a proper zalloc() func (one that does a zeroing
alloc), and removes duplicate prototypes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The MAKEALL script cleverly runs make with the appropriate options
to use all of the cores on the system, but your average U-Boot build
can't make much use of more than a few cores. If you happen to have
a many-core server, your builds will leave most of the system idle.
In order to make full use of such a system, we need to build multiple
targets in parallel, and this requires directing make output into
multiple directories. We add a BUILD_NBUILDS variable, which allows
users to specify how many builds to run in parallel.
When BUILD_NBUILDS is set greater than 1, we redefine BUILD_DIR for
each build to be ${BUILD_DIR}/${target}. Also, we make "./build" the
default BUILD_DIR when BUILD_NBUILDS is greater than 1.
MAKEALL now tracks which builds are still running, and when one
finishes, it starts a new build.
Once each build finishes, we run "make tidy" on its directory, to reduce
the footprint.
As a result, we are left with a build directory with all of the built
targets still there for use, which means anyone who wanted to use
MAKEALL as part of a test harness can now do so.
Signed-off-by: Andy Fleming <afleming@freescale.com>
* 'master' of /home/wd/git/u-boot/custodians:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
* 'master' of /home/wd/git/u-boot/custodians:
i2c:designware Turn off the ctrl when setting the speed
i2c: Add support for designware i2c controller
sh: i2c: Add support I2C controller of SH7734
* 'master' of git://git.denx.de/u-boot-i2c:
i2c:designware Turn off the ctrl when setting the speed
i2c: Add support for designware i2c controller
sh: i2c: Add support I2C controller of SH7734
* 'master' of /home/wd/git/u-boot/custodians:
Blackfin: bfin_sdh: drop dos part hardcode
Blackfin: move gd/bd to bss by default
Blackfin: gd_t: relocate volatile markings
* 'master' of git://git.denx.de/u-boot-blackfin:
Blackfin: bfin_sdh: drop dos part hardcode
Blackfin: move gd/bd to bss by default
Blackfin: gd_t: relocate volatile markings
* 'master' of git://git.denx.de/u-boot-nds32:
board/adp-ag102: add configuration of adp-ag102
board/adp-ag102: add board specific files
nds32/ag102: add ag102 soc support
nds32/ag102: add header support of ag102 soc
In hardware revision 1.20 one more fan controller is added to dlvision-10g.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Print fpga info at last_stage_init on gdsys 405ep boards.
Use dtt_init() to startup fans.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In order to add boards that have different hardware for fpga reset,
any 405ep gdsys board now provides these functions:
void gd405ep_init(void);
void gd405ep_set_fpga_reset(unsigned state);
void gd405ep_setup_hw(void);
int gd405ep_get_fpga_done(unsigned fpga);
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
