Add EXT filesystem support to SPL.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
[trini: Fix a warning and checkpatch problems]
Signed-off-by: Tom Rini <trini@ti.com>
it is not correct to init for a specific slave in spi_setup_slave.
instead buffer the values and delay init until spi_claim_bus.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
the second reset prevents other registers to be written.
This will prevent to have the correct signal levels for
SCLK before writing to the config reg in spi_xchg_single.
Tested with GPIO based chipselect and SPI_MODE_3 on i.MX6S
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Just move the configuration options scattered all over the driver
to the top of the source file. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add short documentation-alike note on how to use the Altera SPI
driver with the EPCS/EPCQx1 FPGA IP block on SoCFPGA Cyclone V
into doc/SPI/README.altera_spi
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The variable d is used in rather questionable way. Rework the code
a bit so it's clearer what it does. Also, rename the variable from
d to data to make it's name less mysterious. Finally, change it's
data type to uint32_t , since it's accessed as a 32bit number.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The driver contained an endless loop when waiting for TX completion,
this is a bad idea since if the hardware fails, the loop might spin
forever. Add timeout and handle it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This patch just zaps most of the checkpatch cries present in the
driver. There is one more left, which will be addressed separately.
There is no functional change.
This patch also adds a bunch of newlines all around the place, this
is to make the code much more readable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Clean up the definitions of bits in the Altera SPI driver, there
is no need to put braces around numbers afterall. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Zap the offset-based register access and use the struct-based one
as this is the preferred method.
No functional change, but there are some line-over-80 problems in
the driver, which will be addressed later.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Rename some defines containing FAT in their name to be filesystem generic:
MMCSD_MODE_FAT => MMCSD_MODE_FS
CONFIG_SPL_FAT_LOAD_ARGS_NAME => CONFIG_SPL_FS_LOAD_ARGS_NAME
CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME => CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION => CONFIG_SYS_MMC_SD_FS_BOOT_PARTITION
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@ti.com>
These types are problematic because they are typically declared in a
non-standard way in U-Boot. For example, U-Boot uses 'long long' for
int64_t even on a 64-bit machine whereas stdint.h uses 'long'.
Similarly, U-Boot always uses 'long' for intptr_t whereas stdint.h mostly
uses 'int'.
This simple test script runs a few toolchains on a few archs to check for
warnings.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use inttypes.h and uint64_t to correct the code so that it will not issue
warnings on 64-bit machines where 'uint64_t' is 'unsigned long'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Unfortunately 'unsigned long long' and 'uint64_t' are not necessarily
compatible on 64-bit machines. Use the correct typedef instead of
writing the supposed type out in full.
Signed-off-by: Simon Glass <sjg@chromium.org>
On 64-bit platforms (like sandbox) 64-bit integers may be 'long' rather
than 'long long'. Use the inttypes header to avoid compiler warnings.
Signed-off-by: Simon Glass <sjg@chromium.org>
inttypes.h defines format specifiers for printf which work with data types of
particular sizes. stdlib.h is currently just a passthrough to malloc.h which
has declarations of the various *alloc functions.
Add the required #define to common.h so that these printf format specifiers
will be made available.
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Replaced with a GPL version from glibc)
There's a definition in stdint.h (provided by gcc) which will be more correct
if available.
Define CONFIG_USE_STDINT to use this feature, or USE_STDINT=1 on the 'make'
commmand.
This adjusts the settings for x86 and sandbox, with both have 64-bit options.
Signed-off-by: Gabe Black <gabeblack@google.com>
Reviewed-by: Gabe Black <gabeblack@chromium.org>
Tested-by: Gabe Black <gabeblack@chromium.org>
Reviewed-by: Bill Richardson <wfrichar@google.com>
Rewritten to be an option, since stdint.h is often available only in glibc.
Changed to preserve a clear boundary between stdint and non-stdint
Signed-off-by: Simon Glass <sjg@chromium.org>
Since i2c_init_all always sets the bus back to CONFIG_SYS_SPD_BUS_NUM
for compatibility reasons, it means that any eeprom not located on this
CONFIG_SYS_SPD_BUS_NUM is not accessible with the eeprom commands, even
if you change the bus number with an i2c dev command before.
Furthermore i2c_init_all should disappear and is currently only called
from the early board initialisation sequences, it is not suited for
other usage.
This reverts commit 01a0c64762.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Align the documentation with the include/linux/etherdevice.h ,
which is where this example comes from. The return value from
the check was inverted in the documentation.
Signed-off-by: Olaf Mandel <o.mandel@menlosystems.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
LaCie Wireless Space has no defined maintainer.
Set myself as maintainer, since I own one of these.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The run command treats each argument an an environment variable. It gets the
value of each variable and executes it as a command. If an environment
variable contains a newline and the hush cli is used, it is supposed to
execute each line one after the other.
Normally a newline signals to hush to exit - this is used in normal command
line entry - after a command is entered we want to return to allow the user
to enter the next one. But environment variables obviously need to execute
to completion.
Add a special case for the execution of environment variables which
continues when a newline is seen, and add a few tests to check this
behaviour.
Note: it's not impossible that this may cause regressions in other areas.
I can't think of a case but with any change of behaviour with limited test
coverage there is always a risk. From what I can tell this behaviour has
been around since at least U-Boot 2011.03, although this pre-dates sandbox
and I have not tested it on real hardware.
Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is old and is using CONFIG_I2C_X, which is wrong.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This is the only used of CONFIG_SPI_X macro, just zap this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Remove this board as this is the only one last user of eeprom_probe(),
which is pretty non-standard stuff.
This patch also removes all the PHP, SQL and CSS stuff from U-Boot,
which probably makes U-Boot a bit less IoT ;-)
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board uses eeprom accessors in an incorrect way. The board
is old and unsupported, just zap it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
This board is the only user of CONFIG_SYS_EEPROM_X40430 , remove
it so the EEPROM command code can be cleansed of the related code
as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
The file board/Marvell/include/mv_gen_reg.h is incompatible with
the GPL (see for example the "MARVELL RESERVES THE RIGHT AT ITS SOLE
DISCRETION TO REQUEST THAT THIS CODE BE IMMEDIATELY RETURNED TO
MARVELL" clause). As this cannot be fixed, we remove the file and all
code that depends on it. Fortunately this only affects some very old
boards that have long reached EOL:
CPCI750
DB64360
DB64460
p3m750
p3m7448
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
The config targets described in README are not present
any more, update the info to currently used targets.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Commit d6b11fd1 (powerpc: remove MBX and MBX860T boards support)
removed mbxbar field in "struct sysconf512x" by mistake and broke
booting on mpc5121 boards. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add example configuration stub for the DWC2 USB controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Pavel Machek <pavel@denx.de>
socfpgaimage utilizes htole32 and friends, unfortunately these functions are
not available on darwin. Fix it by using the cpu_to_le32 and friends defined
in compiler.h as other parts in mkimage do.
This patch fixes the following error:
---8<---
HOSTCC tools/socfpgaimage.o
tools/socfpgaimage.c:77:22: warning: implicit declaration of function 'htole32' is invalid in C99 [-Wimplicit-function-declaration]
header.validation = htole32(VALIDATION_WORD);
^
tools/socfpgaimage.c:80:22: warning: implicit declaration of function 'htole16' is invalid in C99 [-Wimplicit-function-declaration]
header.length_u32 = htole16(length_bytes/4);
^
tools/socfpgaimage.c:95:6: warning: implicit declaration of function 'le32toh' is invalid in C99 [-Wimplicit-function-declaration]
if (le32toh(header.validation) != VALIDATION_WORD)
^
tools/socfpgaimage.c:97:6: warning: implicit declaration of function 'le16toh' is invalid in C99 [-Wimplicit-function-declaration]
if (le16toh(header.checksum) != hdr_checksum(&header))
^
4 warnings generated.
...
HOSTLD tools/dumpimage
Undefined symbols for architecture x86_64:
"_htole16", referenced from:
_socfpgaimage_set_header in socfpgaimage.o
"_htole32", referenced from:
_socfpgaimage_set_header in socfpgaimage.o
"_le16toh", referenced from:
_verify_buffer in socfpgaimage.o
"_le32toh", referenced from:
_verify_buffer in socfpgaimage.o
ld: symbol(s) not found for architecture x86_64
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Pavel Machek <pavel@denx.de>
This is not used anywhere, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Pavel Machek <pavel@denx.de>
Switch to the common spl.h file and zap the arch/spl.h . Since the arch/spl.h
contained various ad-hoc symbols, zap those symbols as well and rework the
board configuration a little so it doesn't depend on them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Pavel Machek <pavel@denx.de>
