The SSUSB IP's clocks come from ssusbsys module on mt7629,
so add its driver
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This adds a general board file based on MT8512 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
This commit is adding the basic boot support for the MT8512 eMMC board.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
For CMD21 tuning data, the 128/64 bytes data may coming in very
short time, before msdc_start_data(), the read data has already
come, in this case, clear MSDC_INT will cause the interrupt disappear
and lead to the thread hang.
the solution is just clear all interrupts before command was sent.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
This patch adds mmc support for MediaTek MT8512/MT8110 SoCs.
MT8512/MT8110 SoCs puts the tune register at top layer, so
need add new code to support it.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Add support for MediaTek MT8512 SoC. This include the file
that will initialize the SoC after boot and its device tree.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Sam doesn't work for Linaro anymore, so Linaro mail is not valid. Change
it to his home mail instead.
Signed-off-by: Sam Protsenko <joe.skb7@gmail.com>
When no partition table is found, users should be warned so.
Warning that no device is available in this case could be misleading,
especially as it is the same error when no device is selected.
Signed-off-by: Alexandre Besnard <alexandre.besnard@softathome.com>
SPL now automatically selects the correct U-Boot image offset for both
eMMC and SD card. No need to tweak
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR anymore.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Armada 38x ROM skips the first SD card offset when loading SPL. This
affects the location of the main U-Boot image. SPL MMC code now supports
U-Boot image offset based on run-time detection of the boot partition.
Use this feature to make the same generated image support both SD card
and eMMC boot partition.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
On Armada 38x platforms the ROM code loads SPL from offset 0 of eMMC
hardware boot partitions. When there are no boot partitions (i.e. SD
card) the ROM skips the first sector that usually contains the (logical)
partition table. Since the generated .kwb image contains the main U-Boot
image in a fixed location (0x140 sectors by default), we end up with the
main U-Boot image in offset of 1 sector. The current workaround is to
manually set CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x141 to
compensate for that.
This patch uses the run-time detected boot partition to determine the
right offset of the main U-Boot partition. The generated .kwb image is
now compatible with both eMMC boot partition, and SD card main data
partition.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
SPL needs DM GPIO to read the SD card-detect signal. This complements
the fix in commit 70bae02f71 ("arm: mvebu: clearfog: fix boot from SD
card").
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
It was observed (on ClearFog Base) that sending MMC APP_CMD returned
an error on the first attempt. The issue appears to be timing related
since even inserting a puts() short debug entry before the execution
added sufficient delay to receive success on first attempt.
Follow the existing quirks pattern to retry if initial issuance
failed so as to not introduce any delay unless needed.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
The eSDHC reference clocks should be provided by speed.c in arch/.
And we do not need CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK option to
select which clock to use. Because we can make the driver to select
the periperhal clock which is better (provides higher frequency)
automatically if its value is provided by speed.c.
This patch is to drop this option and make driver to select clock
automatically. Also fix peripheral clock calculation issue in
fsl_lsch2_speed.c/fsl_lsch3_speed.c.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The QorIQ eSDHC controller supports two reference clocks. They are
platform clock and periperhal clock. The global variable sdhc_clk
has already been used for platform clock.
This patch is to add another global variable sdhc_per_clk for
periperhal clock, which provides higher frequency and is required
to be used for SD UHS and eMMC HS200/HS400 speed modes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The below patch added eSDHC periperhal clock code initially.
2d9ca2c mmc: fsl_esdhc: Add peripheral clock support
The purpose was to fix up device tree properties "peripheral-frequency"
so that linux could get the periperhal clock by it.
However the implementation on both u-boot and linux was only
for a Freescale SDK release. The linux part implementation had never
been upstreamed. These code should not have been exist on u-boot
mainline.
Let's remove the powerpc part changes but keep the changes in
fsl_esdhc driver. The changes in fsl_esdhc driver could be utilized
to support SD UHS and eMMC HS200/HS400 speed modes for current
Layerscape ARM platforms.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fdt fixup for properties "peripheral-frequency" and "adapter-type"
was once for a Freescale SDK release. The properties haven't been existed
in linux mainline. Drop these useless code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The device tree compiler expects that a node with a unit-address has a reg
property.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some features implicitly depended on MALLOC_F and OF_LIBFDT and would
fail at link-time if these features were not enabled.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Add stub for dma_memcpy() and dma_get_device when CONFIG_DMA is
disabled. This avoids ifdefs in driver code using DMA APIs
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use
macros such as CONFIG_IS_ENABLED() that allow conditional compilation of
code for SPL and U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
UEFI programs like GRUB make change terminal colors which requires support
for ANSI escape sequences.
Let CONFIG_EFI_LOADER=y imply CONFIG_VIDEO_ANSI.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Use the correct protocol in efi_uc_stop() when detaching the driver from
the controller.
Change the block IO unit test for the block device driver to throw an error
instead of a todo if teardown fails.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
For automating testing we should be able to power off the test system.
The implementation of EFI_RESET_SHUTDOWN requires the do_poweroff()
function which is only available if CONFIG_CMD_POWEROFF=y.
Enable CONFIG_CMD_POWEROFF if PSCI reset is available.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add compatible "fsl,imxrt-usdhc" to make mmc working on i.MXRT platforms
with CONFIG_DM_MMC=y.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Not all architectures(i.e. i.MXRT) support mxc_get_clock() and use DM_CLK
instead. So building could result in failure due to missing
mxc_get_clock().
Make if(CONFIG_IS_ENABLED(CLK)) an #if statement.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Add i.MXRT compatible string and cpu type support to lpuart driver,
to use little endian 32 bits configurations.
Also according to RM, the Receive RX FIFO Enable (RXFE) field in LPUART
FIFO register is bit 3, so this definition should change to 0x08 as done
for i.MX8. It needs also to set baudrate the same way as i.MX8 does.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
This driver assumes that lpuart clock is already enabled before probing
but using DM only lpuart won't be automatically enabled so add
clk_enable() when probing if CONFIG_CLK is defined. If clock is not
found, because DM is not used, let's emit a warning and proceed, because
serial clock could also be already enabled by non DM code. If clock is
found but cna't be enabled then return with error.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
