If u-boot is installed on the internal emmc, then this will
allow to boot without failure.
Signed-off-by: Wolfgang Zarre <lxdev12@zirdeon.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdhci in SPL to support loading of FIT image from SD
and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3588-rock-5b with new defaults.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3588-evb with new defaults.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config options to include useful gpio and regulator cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Remove CONFIG_DEBUG_UART_ANNOUNCE=y to remove debug messages.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like other Rockchip SoCs, DM_RESET and DM_REGULATOR_FIXED is useful
across RK3588 platform. Select them from arch Kconfig.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 3 Model A.
Unlike prior generation SoCs the BootRom in RK3568 can read all data and
look for idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1384448 bytes read in 119 ms (11.1 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x152000
1179648 bytes written, 204800 bytes skipped in 9.901s, speed 143185 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3568-rock-3a with new defaults.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Remove the CONFIG_SPL_PMIC_RK8XX=y option, the pmic is not used in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3568-evb with new defaults.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config options to include useful gpio, i2c, pmic and regulator cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Add config options to enable support for the RK809 PMIC.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3566-radxa-cm3-io with new defaults. Also add
missing supported mmc modes to sdhci node.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph-all prop to xin24m clock node, it is referenced by cru node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the same prop as linux to control the use of fifo or dma mode. Also
add a u-boot,spl-sfc-no-dma prop to control the same in SPL.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add drivers for PCIe , phy, and command.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the PCIe 2x1l 2 device and associated combphy.
On this bus, the Rock5B has an Ethernet transceiver connected.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
[eugen.hristev@collabora.com: minor tweaks]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
[jonas@kwiboo.se: add PCIe pins]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the node for PCIe 2x1l 2 device together with the corresponding
combphy.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[eugen.hristev@collabora.com: moved to -u-boot.dtsi, minor
adaptations]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
[jonas@kwiboo.se: adapt to kernel node]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable CONFIG_ROCKCHIP_SPI_IMAGE to build u-boot-rockchip-spi.bin.
Define CONFIG_SYS_SPI_U_BOOT_OFFS to write u-boot.itb at the expected
offset. Enable CONFIG_LTO to reduce size of SPL so that the mkimage
output fit before the 0x60000 offset in u-boot-rockchip-spi.bin.
=> sf probe
SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1442304 bytes read in 27 ms (50.9 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x160200
1421824 bytes written, 20480 bytes skipped in 9.501s, speed 155432 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on ROCK Pi 4.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on RockPro64.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Loading part of TF-A into SRAM from eMMC using DMA fails on RK3399
similar to other Rockchip SoCs. Checksum validation fails with:
## Checking hash(es) for Image atf-2 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-2' image node
spl_load_simple_fit: can't load image loadables index 1 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Add a device tree property, u-boot,spl-fifo-mode, to control when the
rockchip_sdhci driver should disable the use of DMA and fallback on PIO
mode. Same device tree property is used by the rockchip_dw_mmc driver.
In commit 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") the DMA mode was disabled using a CONFIG
option on RK3588. Revert that and instead disable DMA using the device
tree property for all RK3588 boards, also apply similar workaround for
all RK3399 boards.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
The workaround to limit number of blocks to read in a single command
should only be applied to RK3568 and RK3588. Change to be more strict
when to apply the workaround.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
Add support for rk3588 phy variant.
The PHY clock is fixed at 100MHz.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
[kever.yang@rock-chips.com: update pcie pll parameters]
Co-developed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[eugen.hristev@collabora.com: squashed, tidy up]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some variants of the PHY have more than just one reset.
To cover all cases, request the rests in bulk rather than just
the reset at index 0.
Co-developed-by: Ren Jianing <jianing.ren@rock-chips.com>
Signed-off-by: Ren Jianing <jianing.ren@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for max_link_speed specified in the PCI DT binding.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
[eugen.hristev@collabora.com: port to latest API, set default correctly,
align to 80 chars]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
[jonas@kwiboo.se: switch to dev_read_u32_default]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The current DT bindings for the rk3588 clock use a different ID than the
one that is supposed to be written to the hardware registers.
Thus, we cannot use directly the id provided in the phandle, but rather
use a lookup table to correctly setup the hardware.
This approach has been implemented already in Linux, by commit :
f1c506d152ff ("clk: rockchip: add clock controller for the RK3588")
Hence, implement a similar approach using the lookup table, and adapt
the existing reset driver to work with SoCs using lookup table.
The file rst-rk3588.c has been copied as much as possible from Linux.
Adapt the clk rk3588 driver as well to bind the reset driver with the
lookup table.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Add pinctrl driver in SPL. Do not remove pinctrl properties for SPL dtb.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To be able to initialize the pinctrl correctly at SPL level and read
u-boot proper from SD-Card, the pinctrl must be initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fixes: 226fce6108 ("phy: Track power-on and init counts in uclass")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Add initial support for the rk3588 PHY variant.
The lookup for the host-port reg inside the struct now does a do {} while()
instead of a while() {} in order to allow a first check for reg == 0.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
phy-supply is now handled at uclass level. Remove it from the drivers that
implement it at the driver level.
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Some phys require a phy-supply property that is a phandle to a regulator
that needs to be enabled for phy operations.
Implement basic supply lookup, enable and disabling, if DM_REGULATOR is
available.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
[jonas@kwiboo.se:
use regulator_set_enable_if_allowed and disable if power_on ops fails]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Enable USB command, USB drivers, PHY and regulators, for USB host
operations.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Add USB 2.0 host nodes and PHYs.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
To quote the author:
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Define SPL_USB_ETH_RNDIS symbol to make it possible to select USB
gadget ethernet support in SPL and U-Boot separately in Kconfig .
Make use of the new symbols in gadget Makefile and move the rndis.o
just below the now merged USB_ETHER symbol in Makefile.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_GADGET and related symbols. Fix typo and
rename SPL_USB_GADGET to "USB Gadget Support in SPL" .
Update the gadget Makefile to match the symbol changes.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_STORAGE and matching SYS_USB_FAT_BOOT_PARTITION .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
To avoid piling up all the various Kconfig symbols in one place, i.e.
common/spl/Kconfig, move the USB Kconfig symbols into drivers/usb/ .
This commit moves SPL_USB_HOST and updates help text of both USB_HOST
and SPL_USB_HOST .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove leftover of
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
When using a list of writeable variables, the initial values come from
the built-in default environment since commit 5ab8105836
("env: Complete generic support for writable list"). Remove unnecessary
misuse of the env is nowhere driver as default environment.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
- Merge in a long-standing fix for some exynos platforms, correct a
Kconfig description, fix some env issues, fix an issue in
devfdt_get_addr_size_index_ptr and look for "panel-timings" not
"panel-timing" per upstream binding.
During refactor this seemed to have been missed.
Fixes: 65dbb128fb ("include: environment: ti: Use .env for environment variables")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
For the devfdt_get_addr_size_index_ptr() function use
map_sysmem() function as cast for the return for use in
sandbox.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
