Commit c4e8862308 (mtd: spi: Switch to new SPI NOR framework)
performs switch from previous 'spi_flash' infrastructure without
proper testing/investigations which results in a regressions for
SST26 flash series.
Enable protection ops for SST26 flash series which were
previously enabled by
Commit 3d4fed87a5 (mtd: sf: Add support of sst26wf* flash ICs
protection ops)
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
mt35xu512aba and mt35xu02g suports Single I/O and OCTAL I/O
also enable use of SPI_NOR_4B_OPCODES.
These flashes are tested on LX2160ARDB and LS1028ARDB respectively
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[jagan: suffix 'ba' on part name and update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
mt25qu512a is rebranded after its spinoff from STM, so it is
different only in term of extended jedec ID, initial JEDEC id
is same as that of n25q512a.In order to avoid any confussion
with respect to name new entry is added.
This flash is tested for Single I/O mode on LS1046FRWY although
it also support QUAD I/O.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This adds support for the Gigadevice gd25lq128 ID needed on the
upcoming libretech-ac board.
SPI_NOR_QUAD_READ is not set since it has not been tested in Quad
mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add Macronix MX66U2G45F flash device description.
This is a 256 MiB part.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Vignesh R <vigneshr@ti.com>
[jagan: use 'g' instead of 'f' in flash name]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for SPANSION s25fl064l
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Add a tiny SPI flash stack that just supports reading data/images from
SPI flash. This is useful for boards that have SPL size constraints and
would need to use SPI flash framework just to read images/data from
flash. There is approximately 1.5 to 2KB savings with this.
Based on prior work of reducing spi flash id table by
Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
