Commit graph

8 commits

Author SHA1 Message Date
Priyanka Jain
4b6067ae9d powerpc/T104xD4RDB: Add T104xD4RDB boards support
T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
    T1040D4RDB is re-designed T1040RDB board with following changes :
    - Support of DDR4 memory
    - Support of 0x66 serdes protocol which can support following interfaces
        - 2 RGMII's on DTSEC4, DTSEC5
        - 1 SGMII on DTSEC3
    - Support of QE-TDM

    Similarily T1042D4RDB is a Freescale reference board that hosts the T1040
    SoC. T1042D4RDB is re-designed T1042RDB board with following changes :
    - Support of DDR4 memory
    - Support for 0x86 serdes protocol which can support following interfaces
        - 2 RGMII's on DTSEC4, DTSEC5
        - 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
    - Support of DIU

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-28 14:40:57 -07:00
vijay rai
2372e283e5 mpc85xx/t104xrdb : remove raw timing parameter
This board uses DDR DIMM. Reading SPD provides more flexibility.
Raw timing parameter code should be removed after debugging.

Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-03-05 12:03:22 -08:00
Tang Yuantian
0023352855 mpc85xx/t104xrdb: convert deep sleep to generic board interface
A new interface is introduced to support generic board structure.
Converts it to use new interface.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-15 09:17:12 -08:00
Priyanka Jain
92f7fed4f7 powerpc/t104xrdb: Set DDR ODT to 75ohm
DDR-ODT require cfg_dram_type switch set properly as per DDR type.
T1040RDB, T1042RDB boards have DDR3L type DDR, so cfg_dram_type
should be set to OFF for DDR3L
Update t104xrdb/README for switch setting

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-09-24 13:11:32 -07:00
Prabhakar Kushwaha
18c0144542 board/t104xrdb: Add support of NAND, SD, SPI boot for T104xRDB
Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.

Initialise/create followings required for SPL framework
      - Add spl.c which defines board_init_f, board_init_r
      - update tlb and ddr accordingly

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:51 -07:00
Priyanka Jain
96ac18c9cc powerpc/t104xrdb: Update DDR initialization related settings
Update following DDR related settings for T1040RDB, T1042RDB_PI
-Correct number of chip selects to two as t1040 supports
 two Chip selects.
-Update board_specific_parameters udimm structure with settings
 derived via calibration.
-Update ddr_raw_timing sructure corresponding to DIMM.
-Set ODT to off. Typically on FSL board, ODT is set to 75 ohm,
 but on T104xRDB, on setting this , DDR instability is observed.
 Board-level debugging is in progress.

Verified the updated settings to be working fine with dual-ranked
Micron, MT18KSF51272AZ-1G6 DIMM at data rate 1600MT/s.

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
2014-03-07 14:53:48 -08:00
York Sun
5614e71b49 Driver/DDR: Moving Freescale DDR driver to a common driver
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-11-25 11:43:43 -08:00
Priyanka Jain
062ef1a662 powerpc/t104xrdb: Add T1040RDB board support
T1040RDB is Freescale Reference Design Board supporting
the T1040 QorIQ Power Architecture™ processor.

 T1040RDB board Overview
 -----------------------
 - Four e5500 cores, each with a private 256 KB L2 cache
 - 256 KB shared L3 CoreNet platform cache (CPC)
 - Interconnect CoreNet platform
 - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
   support
 - Data Path Acceleration Architecture (DPAA) incorporating acceleration
 for the following functions:
    -  Packet parsing, classification, and distribution
    -  Queue management for scheduling, packet sequencing, and congestion
       management
    -  Cryptography Acceleration
    - RegEx Pattern Matching Acceleration
    - IEEE Std 1588 support
    - Hardware buffer management for buffer allocation and deallocation
 - Ethernet interfaces
    - Integrated 8-port Gigabit Ethernet switch
    - Four 1 Gbps Ethernet controllers
 - SERDES Connections, 8 lanes supporting:
    - PCI
    - SGMII
    - QSGMII
    - SATA 2.0
 - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
   Interleaving
 -IFC/Local Bus
    - NAND flash: 1GB 8-bit NAND flash
    - NOR: 128MB 16-bit NOR Flash
 - Ethernet
    - Two on-board RGMII 10/100/1G ethernet ports.
    - PHY #0 remains powered up during deep-sleep
 - CPLD
 - Clocks
    - System and DDR clock (SYSCLK, “DDRCLK”)
    - SERDES clocks
 - Power Supplies
 - USB
    - Supports two USB 2.0 ports with integrated PHYs
    - Two type A ports with 5V@1.5A per port.
 - SDHC
    - SDHC/SDXC connector
 - SPI
    - On-board 64MB SPI flash
 - I2C
    - Devices connected: EEPROM, thermal monitor, VID controller
 - Other IO
    - Two Serial ports
    - ProfiBus port

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: fixed Makefile]
Acked-by: York Sun <yorksun@freescale.com>
2013-11-13 12:41:28 -08:00