When CONFIG_SYS_FSL_ERRATUM_A009801 is defined but
CONFIG_SYS_FSL_ERRATUM_A008511 not defined, there is compile error
that temp32 undeclared, this patch fixes it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
DDR controller 5.2.1 has this erratum A008511 partially fixed.
The workaround needs to be adjusted to take advantage of Vref
training. This patch enables the training and force output
enable to be off.
Erratum A009803 requires the controller to be idel before enabling
address parity. It was combined with workaround for A008511. With
new A008511 flow, this flow needs to be changed to enabling
data init (D_INIT) after the address parity is enabled.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
32 more debug registers are added for newer DDR controllers.
Signed-off-by: York Sun <york.sun@nxp.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Add condition of checking the enabled of address parity
for erratum A-009803, if parity is not enabled, the
workaround of erratum A-009803 should not be applied.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During DDR-2133 operation, the transmit data eye margins determined
during the memory controller initialization may be sub-optimal, set
DEBUG_29[12] and DEBUG_29[13:16] = 4'b0100 before MEM_EN is set.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The initial training for the DDRC may provide results that are not
optimized. The workaround provides better read timing margins.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Per the latest erratum document, update step 4 and step 8, only
DEBUG_29[21] is changed, all other bits should not be changed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During initial DDR training, false parity errors may be detected.
This patch adds workaround to fix the erratum.
Tested on LS2085QDS and LS2080RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
During the receive data training, the DDRC may complete on a
non-optimal setting that could lead to data corruption or
initialization failure.
Workaround: before setting MEM_EN, set DEBUG_29 register with
specific value for different data rates.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the errata A008336 and A008514 do not apply to all LS series SoCs
(such as LS1021A, LS1043A) we move them to an soc specific file
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The workaround requires different setting for range 1 vs 2.
Also adjust timeout value for waiting for controller to be idle.
Signed-off-by: York Sun <yorksun@freescale.com>
BIST test code has a typo, resulting the binding registers not
maintained as expected. This typo results BIST runs twice on
the covered memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Reported-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
This erratum only applies to general purpose DDR controllers in LS2.
It shouldn't be applied to DP-DDR controller. Check DDRC versoin number
before applying workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
Add built-in memory test to catch errors after DDR is initialized, before
any other transactions. To enable this test, define CONFIG_FSL_DDR_BIST.
An environmental variable "ddr_bist" is checked before starting test.
It takes a while (several seconds) depending on system memory size.
Signed-off-by: York Sun <yorksun@freescale.com>
Controller number is passed for function calls to support individual
DDR clock, depending on SoC implementation. It is backward compatible
with exising platforms. Multiple clocks have been verifyed on LS2085A
emulator.
Signed-off-by: York Sun <yorksun@freescale.com>
Internal memory controller counters can reach a bad state after
training in DDR4 mode if accumulated ECC or DBI mode is eanbled.
Signed-off-by: York Sun <yorksun@freescale.com>
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When accumulated ECC is enabled, the DQ_MAP for ECC[4:7] needs to be set
to 0, i.e. 0->0, 1->1, etc., required by controller logic, even these pins
are not actually connected.
Also fix a bug when reading from DDR register to use proper accessor for
correct endianess.
Signed-off-by: York Sun <yorksun@freescale.com>
Previously the driver was only tested on Power SoCs. Different barrier
instructions are needed for ARM SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
